Search Documents

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By Scott E. Winston, Spencer C. Watson

Dynamite is a generic term for a variety of high explosive formulations containing a blend of liquid and solid nitrate esters co-mixed with solid oxidizers and carbonaceous fuels. Dynamites can be divided into general classes of nongelatins, semi-gelatins, and gelatins which vary as to their detonation rates, densities, and water resistance. There are also numerous products within each classification depending on their utilization or on their permissibility in various types of underground mining operations.

Jan 1, 1985

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By Dale Preece, Steven Case, Cassidy McAllister

Simplot Phosphates produces high quality phosphate fertilizer through open pit mining. The operation near Vernal, UT began as a three-pass mining process carried out with drill and blast followed by the combined effort of shovel-truck and dozer material removal. The first two passes removed the overburden and the final pass mined the relatively hard phosphate ore for processing at the mill. Vertical blastholes were employed in all of the mining passes.

Jan 1, 2012

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By Tristan Worsey

This work was performed during the summer of 2008 during the junior year of a BS in Mining Engineering. It was observed that the mine was having a problem with back break during the blasting of development drifts. The unwanted back break was causing the mine extra costs in ventilation, ore dilution, ground support, back fill, explosives and man-hours. The blasting practices were observed for four weeks and the problems and their solutions were defined. In this paper the reasons and causes of the problem are explained with the proposed solutions to eliminate back break.

Jan 1, 2010

By Jeff Senules, Oana Meins, Catherine Aimone-Martin, Scott Lanker, Brent Meins

Global wall strains from 4 to 77 micro-strains were measured at three structures adjacent to a highly-confined Florida quarry blast when PPV amplitudes ranged up to 6.05 in/s. Increasing the peak zero-crossing frequencies with carefully control delay timing helped to lower ground displacements affecting wall strains.

Feb 1, 2020

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By Trevor Ames

Highwall instability, and sometimes referred to as ground failures, historically are a consistent contributor of mine injuries and fatalities within surface mines. To combat this several efforts, including those from NIOSH (CDC), to educate the mining community with insightful literature focused on hazard recognition and advances in ground monitoring systems have been performed. The question is can more be done or is this our last line of defense to manage potential dangers? Is there a more effective method to reduce hazards presented by ground failures including rockfalls?

Jan 1, 2015

By Lee Julian

Ground vibrations generated by mine blasting must be controlled to comply with legislation and to protect sensitive local or site infrastructure. The consequences of exceeding imposed limits can range from negative publicity to structural damage to infrastructure. It is imperative that vibrations are controlled without compromising fragmentation and delivery of blasted inventory. General practice is to reduce the charge weight and the blast size as blasting approaches the sensitive structures; however such an approach results in blasting smaller volumes more frequently which places greater pressure on production to meet their targets.

Jan 1, 2014

By Frank Sames

Ground vibration levels are generally predicted using equations such as the USBM equation implementing the scaled distance concept and describing geological and blast design parameters in a ground transmission constant.

Jan 1, 1995

By Raj K. Rajamani, Solomon A. Tucker, Michael K. McCarter

"In a study aimed at exploring possible improvements in operating performance at an Open Pit Copper (OPC) mine in the western U.S., the impact of blast energy changes on crushing performance was evaluated. OPC feeds its 3-stage crushing plant in 12-hour-day shifts with skarn ore from three domains: Pit_B (B), Pit_S Low-Grade (SLG) and Pit_S High-Grade (SHG), in the blending ratio 1:1:1 (B/SLG/SHG). Thecrushed product is fed to a 2-stage ball mill circuit. "

Jan 1, 2017

By Mike Cammack

Western South Dakota is predominately an agricultural area, with exception of the mining and timber industries in the Black Hills region. With precipitation rates averaging below fifteen inches per year, water is a precious commodity to the livestock industry. There is a constant demand for the construction of earthen water storage facilities (dugouts) to catch snow and rain runoff, or developing natural springs.

Jan 1, 1993

By John R. Schuring, Walter Konon

The 2.0 in./sec. peak particle velocity criterion traditionally used to protect structures from blast induced vibration damage is non-conservative for landmark structures. Various factors which must be considered in establishing vibration criteria for landmark structures are discussed. Existing criteria by past investigators for this class of structure are presented.

Jan 1, 1984

In the office, on the wall to the right of my desk is a large map of the world. Some people stick pins in maps like this to show where they’ve been. If I did that my map would be a mess and look like a pin cushion. I was so fortunate to have been able to see how people live and blast in other parts of this beautiful planet. We l l , maybe some parts weren’t so beautiful and maybe some parts that were beautiful were hell holes for those living t h e re . Every time I re t u rn to the good old US of A, I say a small prayer in thanks for having been born and raised in a land of freedom and plenty. So many places and people have not been so blessed.

Jan 1, 2004

By Jorge Blázquez, Pablo Ravanal, Paulo Couceiro, Juan Navarro

Blasting performance is influenced by rock mass properties and blast design parameters. From them, the rock is the only variable that cannot be modified, but it can be measured, so that, blast design variables can be adapted to optimize the results. A new methodology to assess rock mass quality from drill-monitoring data from both autonomous and manual rotary drilling modes is described to guide blasting in open pit operations. For that, a thorough normalization process has been developed to minimize external influences induced in the data by the rig system for autonomous mode and by the operator intervention for manual mode. Principal component analysis has been used to combine MWD information. Two rock description indexes are derived directly from Measurement While Drilling (MWD) data collected. The first index is a Structural factor that classifies the rock mass condition in three classes (massive, fractured and heavily fractured). The second index is a Strength factor that classifies the rock according to the strength properties. Both indexes have been combined to obtain an overall drilling rock factor along the hole. This has been named by the authors as the X-Rock model.

Feb 6, 2023

By Richard Brummer, John Hadjigeorgiou, Patrick Andrieux

Some of the major challenges associated with underground mining at depth and/or under high extraction ratios are related to the resulting high stress levels, which can lead to the failure and collapse of the rock mass surrounding the excavations. Sudden and violent failures, which can have severe consequences, represent the highest degree of difficulty in terms of underground personnel exposure, erratic and unpredictable production, ground rehabilitation requirements, possible reserve losses and overall mining costs.

Jan 1, 2012

By W. L. Saunders, Richard T. Dana

The dynamites are graded according to the percentage of nitroglycerin that they contain. Thus a “40% powder” would be one in which the sticks, weighing one-half pound each, would include one-fifth of a pound of pure nitroglycerin. Dynamite is usually packed in paper cartridges weighing about one-half pound each which will vary in diameter. When ordering, it is customary to specify a size of cartridge that will as nearly as possible fill the drill hole, the commonest size being 1 ¼” in diameter by 8” in length. It is nearly always shipped in 50-lb. boxes, which have a volumetric capacity of 3/4 cu.ft.

Jan 1, 2013