Search Documents

By R Mancini, G Borla

This paper analyses the first results of a part of an EEC research project ("Blasting control for underground mining"). This research that involves three universities (Paris, Torino and Leoben) has been carried out at the Eisenerz test mine in Austria. In the experimental campaign here reviewed, parallel holes rounds have been fired "decomposed", which means with enough delay between the explosions of the successive blastholes groups to allow for a separate evaluation of their effects on the rock. The seismic effects have been recorded by geophones placed at small distance from the blast, the aim being to find out correlations between the features of the seismogram and the good or poor performance of the single blastholes, or of the groups pertaining to the same delay. Indeed, the seismogram is the only safe and cheaply obtainable description of what happens during the blast. The seismogram should be transformed in a diagnostic tool in the round 'calibration' stage, and in a routine control device during excavation.

Jan 1, 1995

By David Davison, Richard Johnson

Metal-oxidant blends are ordinarily unsuitable as diiect replacements for explosives, because the reaction occurs too slowly. Oxide coatings protect metals, preventing or delaying reaction. By contrast, the electrically-activated reactive composites described below are configured as metal fibers or foils in close proximity to oxidants, with continuous electrical paths from one end to the other. By quickly vaporizing the metal component with an electrical pulse, a reactive composite will be activated, and the reaction will occur rapidly.

Jan 1, 1999

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By John Eloranta

This paper is a case study showing the assembly of available rock property parameters for the purpose of blast design. Blast optimization now includes subsequent milling and requires a full knowledge of the rock mass. Individual blast holes should be designed using all available data. The parameters include: geologic layer from diamond drilling, shovel performance, crushing plant experience from that area, drill monitoring, magnetic susceptibility from a downhole probe, size analysis history from digital image analysis, compressive strength tests of problem areas and cross hole sonic testing. Bedding thickness observed from drill core appear to have a strong influence on fragmentation.

Jan 1, 1996

By Evan Jannoulakis, Wilfrid Comeau

Using the Scaled Distance (SD) and the vector sum Peak Particle Velocity (PPVvs) from a single delay, preferably single blasthole, in a shot, a number is derived which has shown itself to be consistently related to blasting efficiency, as experienced by one of the authors of this paper over the last thirty years. The numbers derived by this process range in value over one order of magnitude more or less. This variation, a function of distance, weight of explosive in the delay, blasthole diameter, blast design, powder factor and the geological environment, can be consistently related to two of these factors, powder factor and distance. In actual use the measured "BED" representing good blasting results should not vary by more than + 33 to + 50 percent of the estimated "BED" in non calibrated cases, and + 10 to 20 percent where previous experience is available. Relatively high "BED" values are indicative of poor blasting results while relatively low "BED" values may be precursors of poor blasting results in a shot. There are many variables in the geological environment which can affect the "BED". A case study is presented from a surface coal mining operation in eastern Canada. This case study tries to evaluate the reasons for the variability in "BED" values derived from multi-hole shots. A problem in using "Signature Vibrations" from a single-hole shot to predict blasting vibrations from multiple-hole production shots is identified.

Jan 1, 1998

By Paul Worsey, Gillian Worsey

The explosives industry is about to reach a critical turning point in human resources. The average age of employees of the largest US explosives company is over 50 and an estimated 5,000 engineers are due to retire from the mining industry over the next decade, with less than 200 mining graduates per year nationally. Not just in the USA, this is a worldwide problem. In Canada the Mining Industry Human Resources Council (MIHRC), reported that older mining engineers are retiring early – at the age of 59.5 on average. It predicts that mining companies will need to hire 370 mining engineers by 2016 and 665 by 2021. The Minerals Council of Australia has predicted the need for an additional 86,000 mining professionals and skilled mine workers by 2020, and the Indian mining industry is also facing a shortage of between 2,500 to 3,000 engineers per year.

Jan 1, 2014

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation. The authors worked with three underground metals mining operations to collect surface blast vibration data produced by heading blasts and stope blasts. The data included blast vibration amplitude values, seismograph records, blast design geometry, charge weights, and detonator delay and sequence designs. The total amount of information was used to produce a regression equation and summary dataset that could be used by the proposed underground mining operation to evaluate blast vibration amplitudes that will be generated on the surface. This work is published and presented so that operations with proposed underground mines or proposed underground mine extensions can use these equations to predict vibration amplitudes on the surface above the mine workings before any blasting occurs.

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Thierry Bernard, Philippe Dozohne

May 13th, in the back country of Nice @arice) collapsed a complete piece of mountain, cutting the RN 2085 and destroying a part of Valabfre’s viaduct. The fist inspections of the site showed that materials had broken loose from surrounding cliffs, The geologists discovered that a block of several thousands of m3 remained suspended in cliff and that it presented a risk raised of gliding. Decision to destroy it by blasting in one blast was there taken by the French department’s council of the Maritime Alps. A race against the clock engaged. Indeed, the RN on 2085 is the main axis connecting the village of Saint Etienne de Tinee and the resort station of ISOLA in the centre of Nice

Jan 1, 2001

By Michael Karmis, Syed Muhammad Tariq, Zeshan Hyder

This paper analyzes the blast design for lime stone quarries of two major cement plants in Pakistan. The production blast of these quarries was resulting in excessive boulders production. At some instances, the rate of boulders production was approximately 10%-15% of the main production blast i.e. if a round of main blast gave around 4000 tons of material; almost 400 to 500 tons of that material was in the shape of massive boulders. This gave rise to increased operating costs requiring boulders collection, drilling and secondary blast.

Jan 1, 2012

By Yu Yalun, He Jun

Wavelet Analysis is very effective for processing the high-varying signals by its good localization properties. We studied its feasibility of application in the field of blasting seismic signals processing, found the basic representation wavelet for blasting seismic signals analysis, and analyzed a concrete engineering example with analyzing wavelet.

Jan 1, 1997

By Malcolm Scoble

The estimation of digging, ripping and blasting requirements in advance of mine production is a difficult task. The characteristics of the superficials and rock mass govern the type and intensity of ground preparation required as a prelude to loading. The incentives for optimum planning of preparation are primarily economic but also relate to mining method and equipment selection, productivity and environmental impact.

Jan 1, 1985

By Erik C. Nygaard

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small bore hole diameters the formation of high amounts of toxic fumes (CO, NO and NOz) can result. In underground blasting, problems can also occur with reduced visibility caused by uncombusted ammonium nitrate.

Jan 1, 1999

By Roberto Folchi

"This article deals with the excavation of a tunnel below the town of Isola LIRI, nearFrosinone, in central Italy. The tunnel was driven into a conglomerate formation, of lacustrine_fluvial origins, consisting in carbonate clasts with a sandy_silty matrix and calcitic cement. ""Drilling andblasting"" had to be adopted in place of a tunnel boring machine which had showeduneconomical performances. Good advance speed rates were achieved notwithstanding thepresence of some above structures to safeguard. The nearest structure (an old votivechapel) was less than 10 meters (33 ft.) far from the tunnel crown; the nearest residentialstructure was at about 15 m (49 ft.)."

Jan 1, 1993

Drilling through unconsolidated material I need to drill blastholes through a mix of consolidated and unconsolidated material. This material is hung up in an underground ore pass. The total length of the holes would be approximately 200 feet. We have attempted to drill through the material with conventional ITH drilling, but were unsuccessful. Does anyone have a suggestion? I am more than willing to bring in a contractor to do the job, if they have solid experience with this type of problem.

Jan 1, 2011

By Y Wada, Y Ogata, T Nishida

"Shaped charge is used for blast demolition of steel construction in general. It is important tocontrol movement of cutting part with shaped charge for the blast demolition of steel construction.Movement of cutting part was studied in the small scale experiment with steel bar. A numericalsimulation using the Discontinuous Deformation Analysis (DDA) was carried out. The DDAmethod was applied to the full scale blast demolition of steel construction. Results of thesenumerical simulation was compared with the blasting demolition work of steel tower."

Jan 1, 1999

By Lindsay Wade, Peter Dare-Bryan

Benches in surface mines often contain known areas of ore and known areas of waste, which must be mined selectively. When rock is blasted it not only fragments but is also physically, and non-uniformly, moved. Risks therefore exist of ore being lost if treated as waste and of mill feed being diluted by waste. Both possibilities carry serious fmancial implications.

Jan 1, 2001

By D J. P Jordan, C V. B Cuningham, A J. Rorke, C G. Ladds, O L. Davey

"During the early stages of the boxcut mining at the Arthur Taylor Colliery, Open Cast Mine(ATCOM), problems were experienced with blasting results. Very large boulders andportions of completely unfragmented rock were commonly encountered. A full blastmonitoring programme was instigated by the mine and the explosive supplier to solve theproblems and to optimise future blasting operations at the mine."

Jan 1, 1993

By Dale Nies, David P. Childs

The open pit gold and silver mining operations in the State of Nevada have historically used simple row by row, echelon, or chevron delay patterns. Common practice has been to use detonating cord trunklines and either detonating cord downlines or nonelectric common in-hole delays in conjunction with surface delays. Several operations use a series of downhole nonelectric delays with an entire row loaded with the same delay to develop similar patterns.

Jan 1, 1991

By Michael Wieland

Delay blasting in underground coal generates shock waves and rifting forces that damage charges remaining in the blast pattern. Damaged charges detonate poorly, raise fume toxicity and reduce coal breakage. Such circumstances could be prevented by using explosives resistant to cross-hole interaction damage. The design of rugged explosives is fraught with contradictory requirements, but tradeoffs related to hard-particle size characteristics prove useful. Hard particles, related voids or trapped bubbles represent reaction nucleation centers which strongly influence the performance of coal mine explosives.

Jan 1, 1992