Search Documents

By Richard A. Dick

Few topics in the blasting industry are more controversial than the proper riming procedure for large-diameter ammonium nitrate-fuel oil (AN-FO) charges, despite the considerable amount of research that has been done both in the laboratory and in the field. The January, April, and June 1975 issues of Emphasis on Blasting contain interesting discussions on priming (5). An ideal primer is one that will surely and efficiently initiate the AN-FO column at the correct location to assure optimum blasting performance. During the 20 years of AN-FO's existence, singlepoint priming, axial priming, multiple-point priming, thermal priming, and shock riming have all been advocated as the "optimum" method. This is not surprising because blasting specialists have often differed on even the most fundamental concepts. To define the optimum primer, we must know what detonation characteristics in the AN-FO column are most desirable. Again, authorities disagree. This paper will discuss conclusions of various studies in an attempt to clear up some of the confusion.

Jan 1, 1976

By J. P. Remi Proulx, Areli Rodriguez, Ruilin Yang

Historically, presplitting has been considered effective in reducing the impact of blast vibrations on highwalls. However, it remains a debated topic: how significantly can it protect highwalls, and is it worth the cost and effort to implement presplit blasting techniques? In hard rock, presplit blasting can leave half-barrels on the highwalls, clearly demonstrating its usefulness. However, in a fractured rock mass, the half-barrels from presplit blasting may not appear in most cases, leading to questions about its role in protecting highwalls. Previous studies in the literature used geophones to measure blast vibrations at far distances and could not ascertain the significant benefit of presplit blasting in reducing the impact of blast vibrations on highwalls. Additionally, no studies in the literature address the role of presplitting in alleviating blasting-released gas pressure that could penetrate joints and open new fractures in highwalls. Yang & Proulx (2019) and Yang et al. (2022) using near-field blast vibration monitoring of signature hole blasts have revealed that the peak particle velocity (PPV) of blast vibrations at a scaled distance of 1 m/kg^0.5 can be reduced by 50% or more for presplit-filtered vibrations. These results have been confirmed for both hard rock and fractured ground. In addition to summarizing the reduction in blast vibrations due to presplitting for both hard rock and a fractured rock mass, this paper demonstrates the relief of subsequent blasting gases after the detonation of blastholes. This is shown through video recordings of gas ejections from a row of empty previously fired presplit blastholes located 6 to 9 meters away from the detonation edge or final buffer row of a blasthole pattern. The results clearly show that presplitting not only lowers blast vibration PPV’s but also reduces the entry of the gases produced by the detonation process into rock fractures and or open joints.

Jan 21, 2025

By Scott Giltner, Allan Koski

Blasting is one of the lowest cost yet most critical parts of the mining cycle. This paper discusses the findings of an audit conducted on the blasting operation at an iron ore mine. The purpose of the audit was to review current blasting practices in order to identify opportunities for production/cost improvements. The approach taken in the audit was to observe general blasting practices, their related downstream effects and to compare current procedures to established best practices.

Jan 1, 2009

By Claude Cunningham

Simple bulk energy rating of explosives obscures the realities of how these deliver their energy, and diverts attention from the key question of controlling blasting results. Explosive performance is directly related to the pressure pulse impacting on the blasthole wall. This is helpfully visualised by comparing the adiabatic expansion plots for explosives of interest on the right scales and axes. The simple comparison of a pure emulsion with pure ANFO illustrates the practical significance of the intrinsic behaviour of these opposed formulations, showing that the emulsion can be expected to work more by softening rock, while ANFO will tend more to crack it. The explanation for these differences lies in the high shock, low sustained pressure of the former relative to the latter. The technique is readily applied, if a good detonation code is available and able to swap data into a spreadsheet. Any differences between codes will emerge most strongly in comparing the gamma plots.

Jan 1, 2002

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995

By Leslie C. Taylor, Anthony L. Kee

Computational modeling of explosively loaded saturated sand on a suspended plate is an inherently complex problem. In this study a computational method is used to predict the dynamic pressure load/impulse from a buried charge. A fully coupled code modeling the explosive charge, sand and air with a Eulerian mesh and the plate structure with Lagrange elements, such as Gemini-Dyna, is an appropriate computational tool. In water-saturated sand, the loadings are soil and water-transmitted shock and bubble or blast effects depending on the depth and the charge size. The computations provide the capability to determine the total impulse load placed on a horizontal plate on or above the soil due to an explosion in the saturated sand for different burial depths in saturated sand and different plate stand off distances. The following test case will be presented: (a) 4.5 Kg (10 lbs) TNT, 10.16 cm (4 in) depth of burial to top of charge, and 20.32 cm (8 inch) stand off distance (Test 4).

Jan 1, 2005

By Larry Schneider

In the construction field and to a lesser degree in mining, flagman are often necessary to move traffic and or pedestrians through work zones. Everyone readily recognizes that they are essential for the safety of the general public and the employees on the job. What is not often considered is the safety of the flagmen themselves. Actually, let’s call these employees “flaggers” recognizing the fact that there are as many women as men doing this job. The first problem we need to overcome is the misperception that flagging is a low skill function that can be done by any untrained employee. The reality is that the flagger works in a very hazardous position with serious responsibility for the safety of his fellow employees and the public at large. And to do this job properly re q u i re s that the flagger receive sufficient training before being sent out to the highway. It is also necessary to convince the flagger of the value and importance of their job in order to motivate them to do a professional job.testing, documentation of both, and accurate re c o rdkeeping are key aspects of HM126F. Of course, training and documentation requirements will vary depending on the type of operation involved, and there may be some differences in the application of requirements depending on your jursdiction. Nonetheless, failure to train and properly document such training can result in heavy fines and/or penalties.

Jan 1, 2004

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By A T. Spathis, J J. Felice, T A. Beattie

High speed cinematography of surface blasting operations is used for diagnosing various aspects of blast performance. Several quantitative features may be derived including confirmation of the hole initiation sequence, time to first movement, evidence of stemming ejection and measurements of face velocity. Face velocity measurements using high speed cinematography have the following disadvantages: firstly, for accurate measurements placement of targets on the face and surveying of them is necessary; secondly, the analysis requires experience and time and can only be done after the film has been developed.

Jan 1, 1991

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

In March of 2001 Barrick Goldstrike Mines, Inc. began evaluating the potential benefits of electronic detonators at the Betze Post open pit gold mine. The original evaluation focused on increased fragmentation, and excavator productivity. During the original evaluation there was an attempt to quantify mill throughput. Early tests indicated that there would be a benefit to mill throughput, however management was hesitant to take on the added cost of electronic detonators based on the initial evaluation. In early 2002 a decrease in mill throughput was being forecast as a result of harder ore being encountered. As a result of the initial electronic detonator evaluation a team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative. This initiative was targeted at improving mill throughput as the harder ores were encountered. Batch tests were conducted to determine if adjustments to drilling and blasting in the open pit could increase mill throughput and justify a 50% increase in drilling and blasting costs for the harder ore material.

Jan 1, 2004

By J P. F Warkentin, A W. Bauer

Recently, significant improvements have been made in both blast design methods and blasting accessories. The introduction of extremely accurate blast delays now allows proper implementation of advanced blast designs. Thus the onus for future blasting improvements has moved from blast design to the need for ensuring that explosives quality is of the highest order. One measurement commonly used to assess explosive performance is the velocity of detonation (VOD).

Jan 1, 1991

By H. S. Venkatesh R. Balachander, G. C. Naveen

During the construction of a 1020 MW underground hydroelectric project in Bhutan a huge rock fall took place in the Downstream Surge Chamber (DSC) during March 2016. The total quantity of rock in the fall area is estimated to be about 1,50,000m3 (2.6 billion cubic feet), out of which about 25,000m3 (0.44 billion cubic feet) of muck was removed. The removal of muck was stopped apprehending that the cavity formed due to the rock fall may get further aggravated leading to widening and destabilising the adjacent transformer hall cavern or it might day light as the top cover was about 190m (623 feet). As the fall has virtually blocked the 314m (1030 feet) long cavern and divided it into two different chambers (south and north), and that the muck cannot be disturbed, it was decided to erect concrete wall on either side of the fall up to the cavern roof and then later address the filling of the cavity with appropriate fill material. As the access to the DSC was there for the southern side it was decided to extend a cable tunnel which was terminated at a distance on the north side of the cavern by D&B so that once it gets punctured into the north wall of the DSC it can be used to access the fall from this front too. This is a unique situation where in every blast approaching the DSC, the parting between them is diminishing and hence the tunnel blast will be exerting axial load on the parting wall leading to dynamic transient loading conditions and buckling may take place on the northern wall of DSC. This paper describes the various drill blast combinations adopted for successful excavation of this tunnel.

Jan 1, 2019

By Larry R. Fletcher, John W. Kopp

The safety record for explosives in U. S. mining is excellent considering that over 4 billion pounds of explosives are now being used each year. However, blasting accidents remain one of the most serious concerns based on the number of injuries, the injury severity rate and the disaster potential. The Bureau of Mines has been analyzing blasting accident data obtained from the Mine Health and Safety Administration (MSHA) to determine the most frequent causes of mine blasting accidents and to examine trends in blasting accidents. This accident analysis is an update of two previous blasting accident studies conducted by the Bureau and published in 1983 and 1987.

Jan 1, 1991

By R Holmberg, P A. Persson

Recent developments in the methods of measuring rock motion close to the contour at the moment of blasting have given an improved understanding of the extent of rock damage caused by different charge systems. The paper presents the new results and the methods of prediction of damage zones which are used in Sweden for the design of contour blasting rounds. A survey is given of the tools and the techniques for smooth blasting that are now used on a routine basis in Sweden.

Jan 1, 1978

By Chuck Kliche, Bill Clements

This project involved the removal of the top of an old water supply reservoir tank for the City of Lead, SD by explosives. The general contract called for the removal of the concrete top without damaging the sides or floor of the reservoir. The option of a rock hammer was eliminated, due to the possibility of an unpredictable collapse damaging the sides or floor of the reservoir. Different blasting options were discussed between the primary contractor and the blasting contractor, along with the pros and cons of each. The primary contractor settled on the option of drilling the structure for blasting versus using shaped charges

Jan 1, 2007

By Marlyn G. King, Robert L. Martin

Blasting activities in all four pits at Thunder Basin Coal's Black Thunder Mine are focused on cast blasting. With widths varying from 190 feet to 265 feet and bench heights varying from 90 feet to 175 feet, casting efficiencies vary with different geometry's. For example, the percent cast to final in the 200 foot pit is on the average higher than the 270 foot pit. The powder factors are somewhat higher in the narrower pits, thus increasing the cost of blasting. This leads to a very detailed look at the actual benefit of cast blasting and the associated cost of these benefits.

Jan 1, 1995

By Wiliam Reisz

As we approach the peak season for thunderstorm activity it’s important to keep in mind that lightning still poses a serious threat to drilling and blasting operations. Lightning remains the number one cause of accidental detonation of explosives.

Jan 1, 2008

By Charles H. Dowding

Public concern over blast-induced CRACKING has led to the search for a radically new approach to vibration control. The present system, while scientifically correct, is cumbersome to explain. Historically the potential for blast-induced cracking has come to be described through velocity time histories, which are correlated with observation of crack extension under controlled experimental conditions. Unfortunately time histories are simply too difficult for jurors and village or county regulatory boards to understand. Furthermore these arbiters must accept on faith that the observers were unbiased. Since these public bodies control the manner in which blasting activity is adjudicated and regulated, information must be presented in a form they can understand and that is not subject to second-guessing.

Jan 1, 1999

By Dieter Froelich, Giles Turcotte

In the near future, Bong Mining Company (BMC) will start mining a new deposit known as Zaweah II which is a narrow iron orebody requiring multiple row blasts with the bench floor as a free face. This called for the development of a new blasting technique. The article delineates the problem and its restrictions related to blasting. It also describes the approach which was taken for developing this new blasting technique which is essentially an application of the cratering theory with near spherical charges. Basic crater tests were conducted using various combinations of hole sizes, explosive strengths and delay patterns. From the results obtained, several alternatives were considered for production blasts and the most promising ones were evaluated.

Jan 1, 1980