Search Documents

By Roger E. Scholl

Data on off-site low-rise building damage from underground nuclear testing at the Nevada Test Site (NTS) of the United States Atomic Energy Commission (AEC) [The AEC has been called the United States Energy Research ant Development Administration (ERDA) since 1975, but because the data presented here were gathered between 1966 and 1970, the AEC rather than ERDA is referred to in this paper.] are available for seven large tests in the period from 1966 to 1970. The data, while sparse, provide an adequate sample for the investigation of motion-damage relationships. Damage in the study is statistically described in terms of the incidence of damage complaints, the incidence of buildings damaged, and damage cost. Using 5%damped response spectrum acceleration amplitude to characterize ground motion, the plotted data fit reasonably well with previous motion-damage relationships established from extensive data available from the 1969 RULISON underground nuclear explosion (UNE) experiment conducted in western Colorado.

Jan 1, 1976

By RR Vandebeek, A W. Bauer

The Canadian Explosives Research Laboratory regularly evaluates the properties of commercial explosives for authorization under the Canada Explosives Act. Propagation sensitivity is normally measured using small scale tests. Relating the results in actual mining practice is difficult. In the mining industry, the propagation sensitivity is a measure of the ability of one cartridge to propagate to an adjacent cartridge in a borehole. They may be separated by a gap of in-filling material. As well the propagation sensitivity will be affected by the explosive type, temperature, degree of coupling, cartridge diameter and other factors.

Jan 1, 1987

By Joe Dannenberg

One must be cautious in talking about blasting safety, because the very act of making a blast involves the creation of an infernal machine. You are setting up for the instant release of tremendous energy. Inherently this is a hazardous act. It has always been hazardous. It will stay hazardous.

Jan 1, 1975

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By Thomas A. Gelormino, Ulrich La Fosse

"Deep blasting was used to densify foundation soils for a large manufacturing facility inChicopee,Massachusetts. A 360,000 square foot building, whose construction began inthe summer of 1990, is founded on alluvial deposits up to 90 feet in depth. These deposits are comprised of saturated very loose to loose fine to medium grained sands with traces of silt and gravel. During the building foundation design it was found that to withstand earthquake forces without soil liquefaction, it would be necessary to improve portions of the alluvial deposits by densification. The zone in need of densification extended from approximate depths of 20 to 50 feet. Several conventional densification methods, including vibrocompaction and deep dynamic compaction, were evaluated along with deep blasting. Detonation of 1-3/4 inch diameter charges of 65 percent gelatin dynamite (Atlas Power Primer) installed inside 2-inch diameter PVC casings to a depth of up to 40 feet, was used to achieve the desired densification. This method was selected over others due to its lower cost and decreased construction time. Although used in New England once in1940 for a dam and once in 1960 for a transmission line tower to improve foundation soils, there is no precedent found in the literature for densification by blasting to improve liquefiable soils below a proposed building. Details of a test program and the production blasting, including vibration data are presented. Pre-and post-blasting data conclusely shows an increase in the density of the sand deposit after blasting."

Jan 1, 1991

By Unknown

ATF has provided a Guide to Recording Suspicious Persons Description in the Safety & Security Brochure. This guide may be useful for recording descriptive information on any suspicious individual. Suspicious activities can be reported to ATF’s 24-hour hotline listed in the front of the Guide or to your local law enforcement authority.

Jan 1, 2009

By Lewis L. Oriard

Ground vibrations associated with blasting are generally in a higher frequency range and of shorter duration than those generated by earthquakes, and the intensity scales for earthquakes cannot be applied directly to blasting vibrations without modification. Further, the profession does not need an intensity scale merely to estimate vibration intensity. If the blasting in question was not monitored instrumentally, it is a simple matter to estimate the range of intensities based on published prediction formulae or data from various sources such as Oriard (1), Nicholls et al (2), Hendron and Oriard (3), Siskind et al (4), and others. However, the profession has a serious need, for purposes of evaluating damage claims, to understand the relationships between vibration intensities and the levels of observed effects. The criteria for threshold damage do not apply to typical cases which usually involve structural damage. If the damage in question would have required ground vibration with a particle velocity of, say, 20-120 ips, damage is not verified by showing that the vibration merely approached a suggested limit to avoid threshold damage. That is not the question. This paper provides some guidelines for comparing severity of damage to intensity of vibration which would be required to cause such damage, much as is done when determining earthquake intensities. In addition, this paper includes a discussion of strain amplitudes induced by environmental forces, the predominant causes of damage to structures. Also, certain popular myths regarding blasting damage are discussed in the paper. Due to space limitations, the paper will not include a discussion of airblast effects.

Jan 1, 1989

By Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due quarry blasting. The natural limestone bedrock in occurs at or near the surface in southeastern peninsular Florida. While the shallow overburden soils is advantageous for mining purposes, vibrations from blasting has been a contentious issue in South Florida due to the proximity of the mines to several residential communities. White Rock Quarries and Krome Quarries are two active mining facilities in South Florida which generate numerous complaints, insurance claims, and lawsuits from residents in nearby communities who claim that the vibrations cause damage to their houses. Both quarries are located on the eastern edge of the Everglades, with thousands of nearby residences at the western edge of development in Broward and Miami-Dade Counties. Data obtained from over 400 publicly available blast monitoring and associated seismograph reports from White Rock Quarries were reviewed and compiled. The data was used to emperically develop a conservative estimate of the ground attenuation rate based on the scaled distance from the blast origin, which can be compared to Figure B-1 from USBM RI 8507 to determine whether it is feasible if damage could have occurred at a given property.

By Brad Johnson

Homestake Mining Corporations' open cut operation at Lead SD. experienced a highwall failure in October of 1993. The failure released a 75' section of rock wall at the 5280' level. It came to rest on the 5200' safety bench. Since work was in progress below the failure, this rock had to be removed for safety.

Jan 1, 1995

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Roger L. Keller, John Dean Smith

The Amax Coal Company's Ayrshire Mine in Southern Indiana is faced with one of the toughest blasting applications concerning vibration in the nation. As a means of maintaining regulatory compliance the operation elected to exercise the option of frequency analysis. A site-specific computer processing program which suggests ideal delay interval ranges for the lowest vibration was utilized.

Jan 1, 1987

By K. G. Holley

Blasting is usually required to produce easily-excavated broken rock, while leaving surrounding rock masses as undamaged and stable as possible. In mining applications, it is common to utilise production blasting in the centre of an open pit, and specially developed limits blast designs when blasting adjacent to the excavation perimeter. In open pit blasting, limits blast designs generally include pre-splitting, trim blasts, or buffer blasts, all of which are designed to limit, or eliminate, damage beyond the designed pit wall. This paper reports on the findings of a study of the profile of damage in rock masses surrounding blasts, determined by a combination of vibration monitoring, displacement monitoring using extensometers, and video inspection of open holes drilled at various distances behind blasts. The results obtained suggest that the profile of damage may extend for the full depth of the bench, for distances of up to 12 to 15 metres behind blasts. This suggests that entire berms may be affected by blasting, displaying loss of friction and cohesion along joint and fracture planes. The study has considered production blasts and trim blasts with small diameter blastholes and pre-splits.

Jan 1, 2004

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By Elias Poulakidas, Marco Arellano

The impact of a higher copper price on the open pit metal mining sector has derived in a faster and safer way in which the mining operation of broken and mineralised material is carried out. In this regard, a good control of bench stability allows a lesser extra removal of material and so more safety to get the planned ore. The stability is ensured through an efficient drilling and blasting, applying the current technology and available know-how. An efficient use of energy through low-density explosives which are the most adequate for the existing solid rock releasing energy in a smoother way through a deterministic detonation sequence which is the application experience presented here. This application experience has two main technological factors; the adequate type of explosive for the kind of rock, in terms of velocity of propagation (Vp) together with the use of a determined detonation sequence and the appropriate designs, which allow to reduce the level of damage to the walls and to maintain a minor backbreaking through quantification with vibration modelling carried out at the near field. The reductions achieved were 30% lower in peak particle velocity.

Jan 1, 2008

By Calvin J. Konya

For proper blast design, one must make the assumption that all blastholes release nearly ideal energy. In many types of blasting operations, blastholes release very little useful energy. These blastholes are called malfunctioning blastholes. Recent studies indicate that as many as 30 percent of all blastholes are malfunctioning. These malfunctioning blastholes are not an unusual occurrence.

Jan 1, 1988

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By L C. Taylor

Very small scale testing has been shown to be able to predict quite accurately, in many situations, the results of full scale testing. Small scale tests are more cost efficient, easily observed, and easily instrumented than full scale tests. Over the past 10 years small scale testing in the Dynamic Effects Laboratory at the University of Maryland has been used to successfully study the response of structures and soils to explosive detonation. Small scale testing has been successfully used to predict full scale results in underwater cratering and channeling, the loading (both pressures and impulse) on vehicles due to the detonation of buried charges, the positive effects of bottom shaping for military vehicles to reduce this loading, and the movement of obstacles underwater by explosive charges.

Jan 1, 2012

By Brent Blanchard

An emergency demolition project related to a bizarre plane crash has reportedly set a new world record for the tallest structure ever explosively demolished. On Sunday, April 22, 2001, 38-year old Gilbert Paquette was killed when his singleengine Cessna 150 struck a 1,217-foot tall communications transmission tower while flying in heavy fog over a remote region of upper Quebec Province.

Jan 1, 2002

By Dale S. Preece, Vanessa S. Berg

Shaped charges are being utilized in defense applications against a wider variety of targets including concrete, rock, and soil. This work was motivated by a heightened interest in characterizing the effect of shaped charge attack on brittle, non-homogenous materials, in particular, concrete damage and penetration predictions resulting from a TOW-2a conical shaped charge (CSC). This paper presents a multi-stage approach for accurately predicting the high explosive detonation and subsequent jet formation due to the collapse of shaped charge liner, the changes in jet length and diameter as a function of standoff distance, and the jet-target impact dynamics. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN to predict the shaped charge jet formation. 2-D finite difference Eulerian subgrids represent the explosive and casings components, while thin components like the liner are modeled with Shell subgrids. The Pugh, Eichelberger & Rostoker (PER) jetting theory option is invoked to obtain the jet and slug masses and associated velocities. The jetting data is post processed where the jet velocity gradient and jet mass is used to solve for the new jet length and diameter gradient at a desired standoff. The final computation involves a 2-D fully Lagrangian model in which the jet and velocity gradient is represented by a string of Lagrangian segments and the concrete target is defined as Lagrangian with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model. This model has a third invariant dependency that accounts for failure mechanisms in brittle materials.

Jan 1, 2004