Search Documents

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By Guy Bridges

Site formation works requiring excavation of rock at the Queen Mary Hospital redevelopment site was restricted due to extremely low ground vibration limits. Non-Explosive excavation method called Electro Power Impactor (EPI), sometimes called Plasma Blasting, was utilised to help ensure the rock excavation rate could meet the required programme.

Feb 1, 2020

By Thomas E. Ricketts

Occidental Oil Shale, Inc. constructed two commercial-sized modified in situ (MIS) retorts, Retorts 7 and 8, at its Logan Wash Oil Shale Mine in February and April 1981, respectively. One of the primary objectives of this two-retort program was to examine large-scale blasting reproducibility for commercial-sized retorts. The blast design used 545 blastholes and 550,000 pounds of explosive in ANFO equivalent per retort. Each retort was blasted using millisecond delay blasting caps tied into a single round. The blasts resulted in rubble beds very close to one another and to predicted results obtained using newly developed limited void blasting technology. The heights of the remaining void rooms over the beds after blasting were within 0.3 feet of one another. This excellent reproducibility is brought into true perspective when compared to the scale of the rubble beds which were 230 feet high with volumes of over six million cubic feet each.

Jan 1, 1984

By Roger Holmberg, Donald Jonson

The Swedish Standard SS 460 48 66, “Vibration and shock - guidance levels for blasting induced vibration limits”, is based on more than 50 years of experience from blasting close to structures and tunnels. The Swedish Standard gives a method for calculation of guidance values for different types of buildings and ground condition under the building. This is done for every building and structure within a predetermined zone. The guidance levels are for the peak particle velocity monitored in vertical direction. The standard is valid for all kinds of blasting project (tunnelling, quarrying, mining etc.) The guidance levels neither take in to consideration discomfort for people inside the building or structure nor vibration sensitive equipment inside the structure. The paper also presents the Swedish Standard SS 02521 “Vibration and shock - Blast induced airborne shock wave - Guidance levels for buildings”.

Jan 1, 2005

By John Dean Smith

In order to discuss problem solving techniques for the future. we must first review the past. This paper will discuss the drilling and blasting problems and techniques that were used by .Imax Coal in the past few years, tn those of today.

Jan 1, 1991

By Tom Snyder, John Brulia

PART 3 – UN Identifi cation Markings for the Highway Transportation in Commerce of Bulk Explosives, Oxidizers, and Combustible Liquids

Jan 1, 2015

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.

By Clara Godoy, J. A. Sanchidrian

In this paper, Machine Learning techniques have been used to combine data monitored from the drill rig with scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure.

Feb 1, 2020

By Robert Hopler

Blasting powder is a slow-acting, black, granular explosive made of sulphur, charcoal and either potassium nitrate (saltpetre) or sodium nitrate. The blasting powder containing potassium nitrate is known as “A” blasting powder; that containing sodium nitrate, as “B” blasting powder. “A” blasting powder is a little denser, a little stronger and a little less hygroscopic than “B” blasting powder.

Jan 1, 2014

By Sri C. Sawmliana, P. Pall Roy

Damage to underground roof and pillars in blasting gallery (BG) panels has been an increasingly important area of study in recent years due to the invention of new explosives and cord systems which has led to the modification and alteration of the design aspects developed by Charbonnage de France (CdF). According to extensive mine experiments conducted by Indian and foreign experts, it has been established that the induced peak particle velocity (PPV) is predominantly related to the emanated seismic energy of a source and the distance from the source. With that concept in mind, nearly 160 experimental blasts were carried out in four BG panels in India under varying geomining conditions. Based on the results obtained thus far, the authors have established predictor equations correlating explosive energy (in Joules) and distance from the shot to that of induced peak particle velocity received at the sensor point. Good correlation was obtained between the actual and the predicted values. It is realized that this equation may be used as an efficient tool to determine the size limit of blasts in BG panels so that the induced particle velocity does not create damage in underground workings as per the established Blast Damage Index (BDI) and other available safety norms.

Jan 1, 2004

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By X. Gumede

A model is being developed to quantify the benefits for mining houses resulting from the reduction in greenhouse gas and energy consumption by the application of innovative blast designs in addition to direct financial benefits throughout the mine to mill value chain. The conversion from shock tube initiation systems to electronics and some changes to powder factor measured on an open pit mine had previously been used to show significant improvement on blast outputs. Benefits were realised on drilling, blasting, loading, hauling and beneficiation. Quantification of the relationship between powder factor and reduced greenhouse gasses is investigated in this study. The study has highlighted new data that must be recorded and hence some assumptions were made as to fuel consumption and the energy in crushing was obtained from the Bond work equation. The mine to mill projects in an open pit platinum mine and a quarry produced energy savings and reduced greenhouse gas emissions associated with the careful application of explosives and blast innovations. The less fines project showed an increased carbon footprint. The model provides a new insight into how project feasibility should be decided based on economic and environmental viability.

Jan 1, 2012

By O. Rielo, P. Katsabanis

Traditionally fine aluminum is not used in dry commercial explosives due to the hazard associated with aluminum dust explosions during mixing. An industrial process has been developed which enables the safe use of paint grade Aluminum with ANFO. The addition of fine aluminum particles resulted in increased velocity of detonation of ANFO compositions. Velocities of detonation, in 52mm (2 1/16 in.) diameter confined charges were 20% higher than velocities of detonation of straight ANFO. The detonation performance of fine grained ANFO was not benefited by Al at the diameter tested. Furthermore use of larger Al flakes resulted in decreased velocities of detonation. The results are compatible with the experience of Al addition to high explosives. Tests were also conducted using bio-diesel, finding no substantial difference in the performance of AN fuel explosive compositions which used bio-diesel.

Jan 1, 2009

By Joel Chipana, Roberto Laredo, Benjamin Cebrian

Ring blasting is a common production method in underground metal mines. As a drill and blast process, it presents particular features that do not correspond with bench blasting in open pit or underground mining.

Jan 1, 2017

By Brian Micke, Mick Gavrilovic

The problem of rock hang-ups in underground mining operations has been a continuing one since the days of the “hang-up man”. This position commanded the highest pay of any underground worker in many historical Western U.S. underground bulk-mining operations, due to the occupational hazards of the job. Although underground mining techniques and especially work practices have changed greatly since then, the hang-up problem is a continuing one in many mines which use gravity flow of coarse rock in their transport systems or in those mines where stressed ground causes rock slabs to spa11 and bridge rock passes and stopes. In addition, with mechanized underground open-stoping mining methods now being used in many different types of ore deposits worldwide, this problem has again emerged as a very significant one in many of these highly mechanized operations. This is especially so where the remote operation of loaders is used for removing blasted rock from underground open stopes.

Jan 1, 1999

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Robert Boehnke, Bernd Mueller

This contribution presents an innovative, statistically supported method to predict blast vibrations in rock mass. For modelling the processes during and after detonation, a theory is employed which is based on linear momentum (so-called momentum theory), strongly supported by new measurement methods. During the course of the investigations, the following parameters have been found to dominantly influence vibrations: ! charge WB, includes geometrical factors such as borehole length and diameter (kg) ! detonation velocity cd of the explosives used (m/s) ! distance r between the points of emission and immission (m) and the statistically determined negative exponent n ! factor RM or RS of the rock mass which is related to the specific blast momentum and the drilling and blasting technique used and is statistically determined together with the exponent m (mm/kg or mms/kgm)

Jan 1, 2004