Search Documents

By W. J. Birch, R. Farnfield, L. Bermingham

Whilst a significant body of research has been carried into air overpressure levels that arise as a result of the use of explosives, few published studies have actually tried to relate the movement of a quarry face to the resulting air overpressure produced. The aim of this preliminary investigation was to monitor a number of quarry blasts at two different limestone quarries. The first using multiple separately initiated deck charges in a multi borehole blast, the second using single column charges in a multi borehole blast.

Jan 1, 2008

By Cam Thomas

"Reflectorless laser survey equipment has made it much easier to take accurate measurements toinaccessible locations in quarries, open pit mines and rock slopes. Prior to the introduction of thereflectorless laser as a working tool, it was not possible to directly measure to inaccessible locations on rock faces. If a person could not occupy the point, only indirect measurements could be made. For blasting work, measuring the burden in front of the first row of holes could only be done approximately, using such techniques as holding a plumb line in over the crest, triangulating in on a few points or “eyeballing” the burden. This led to direct and significant problems with blasting, including flyrock and airblast (caused by insufficient front row burden), excessive vibrations, problems with oversize and tight digging (all of which may be caused by excessive front row burdens)."

Jan 1, 1999

By P. Couceiro, J. Navarro

A new methodology to perform selective blast designs by adapting the explosive energy, hole by hole (or in the hole), to the rock properties as a combination of their strength properties through the X-Rock model has been developed based on drill-monitoring data from both autonomous and manual rotary drilling modes. For that, a thorough normalization process has been developed to minimize external influences in the data induced by the different rig system and the operator interventions during manual drilling operation. Principal component analysis has been used to combine drill monitoring information. Data from 48,385 blastholes, comprised in 102 production blasts at 7 different levels in one expansion of the mine have been used for the analysis. The methodology, called X-Energy, combines the X-Rock model outputs with actual blast design parameters (drill pattern, stemming and borehole length, explosive mass/density and others) and a constant variable obtained from a machine learning algorithm, to estimate size distribution and percentage of fines and coarse material, hole by hole, by combining and recalibrating the Kuznetsov (Cunningham, 1987) based equation. From it, a new shovel-independent diggability model has been developed as combination of the P80 size, the rock properties (from the X-Rock) and a constant variable obtained from a machine learning algorithm. The X-Energy application presented in this study have been implemented in Minera Escondida Limitada (MEL), to design and operate production blasts with the goal of varying the explosive density to the rock properties to obtain a more uniform size distribution and digging rates, hole by hole, based on a target size and rate, and improving slope care, preventing active faults to fail. The methodology has been applied and validated in 17 production blast (8,277 blasthole), unlocking an average of 12.8% reduction in explosives costs (explosive consumption), by combining a pattern expansion strategy and a better distribution of the explosive density within the blast. The results demonstrate how a better distribution of the explosive energy by varying its density in the hole according to the rock and blast geometry variables can reduce powder factor (explosive consumption) while improving or maintaining blasting and digging results.

Jan 1, 2024

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

Reducing costs while maintaining productivity and achieving good results is a constant challenge in mining operations, especially in the drilling and blasting stage, since a bad blast can affect production plans, increase costs, affect safety and jeopardizing the pit stability. Examples of undesirable blasting effects are: flyrocks, boulders, loading equipment damages, lower production rates, etc. In some of the biggest open pit mines using conventional blasting patterns visited by the authors, the pattern does not adjust properly to the rock mass, in most cases blasting polygons are large and the rock mass condition is variable within the designed blasting pattern. On the other hand, conventional blasting patterns with stemming columns use 40-50% of the blast hole with inert material (the stemming). Moreover, blasting engineers spend efforts to improve fragmentation results by increasing explosive charge in spite of having the negative effect of ground vibrations, with little or no success. The classic approach is "the more explosive in, the better the fragmentation is", furthermore it is assumed this relation is direct and infinite, but it is definitely wrong. This work challenges the notion of a limitless direct relationship between explosive charge and fragmentation, this means this is partially true but just up to a certain limit. In other words, there is still room to improve energy distribution among the classical blasting techniques without increasing the explosive energy by using air decks. In the work to be presented air decks are built using conical shaped stemming plugs called Paraplug®. The results obtained suggests a wedge effect acts in the bottom of the stemming column that cushions the shock wave and the air deck to reduce the detonation pressure (this is due to the decoupling factor resulted from the air deck). The demonstration shows improvements in fragmentation results, reduced vibration records accompanied with lower dust column and costs savings in explosive charge.

Jan 21, 2025

By Tom Hale

Developers and blasters are faced with increasing public demand and regulatory restrictions to maintain the lowest possible levels of noise and vibration from blasting operations in populated urban areas. Pyrotechnic products have proven to be a low noise, low vibration alternative to conventional blasting for close-in rock excavation and concrete demolition applications. Pyrotechnic breaking charges often yield 1/10th the vibration and noise compared to traditional explosives, and have been demonstrated to increase public confidence and decreased damage potential where they have replaced explosives, thus allowing new opportunities for work and greater job profitability. This paper presents a practical approach to utilizing pyrotechnic products in various applications including trenching, mass excavation, demolition, and dimension stone production, providing methodology for pattern design, vibration probability and loading calculations. Field research data is reviewed and compared to conventional explosives.

Jan 1, 2008

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Daniel B. Conn, John L. Floyd

PhotoSeis™ is a blast analysis method that combines the advanced technologies of high speed motion picture photography and digital seismology. When fracturing rock with the use of explosive energy, the human eye cannot detect the details of the process due to its short duration. An extended time base is required to accurately quantify the response of the rock mass to the detonation process. This time base is provided by the use of high speed motion picture cameras. The control of ground vibrations and airblast is an important consideration when developing efficient blast designs. High vibration and airblast levels can be an indication of improper design, inaccurate detonators, or adverse geology. Since many factors can elevate airblast and ground vibration, a greater understanding of the site specific response to the blast design is needed that is beyond the scope of simple seismographic recordings. By synchronizing the photographic record provided by the high speed motion picture cameras with the airblast and vibration information from digital seismological monitoring, the Photoseis™ technique can be of great assistance in controlling airblast and vibration and optimizing the use of explosive energy for rock fragmentation.

Jan 1, 1990

By Kyle Wagner, William Joa, Colter Angell, Catherine Johnson, Marty Langenderfer, David Doucet

The goal of any business is to seek the maximum profitability for the organization through optimization the use of resources, processes and the application of new technologies. An analysis of various case studies demonstrate that blasting can have positive impacts on the crushing and milling processes resulting in increased profitability for the mining industry (Grundstrom, Kanchibotla, Jankovich & Thornton, 2001). This paper describes the case study of two copper mines in Peru producing Cu-Mo and Cu-Au concentrates, which together with their strategic partner, have implemented a project focused on the improvement of rock fragmentation. The project was based on techniques of pattern size reduction, the use of high energy explosives and the technology of electronic initiation. Combined, these techniques were shown to have significantly impacted the efficiency of downstream processes.

Jan 1, 2019

By P A. Lang

Canada is constructing an Underground Research Laboratory as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in stable rock formations. Careful blasting methods have been designed and quality control procedures have been used for the excavation of the access headings in the underground facilities. This paper describes the work done between 1984 December and 1986 December at the second level, 240 metres below surface.

Jan 1, 1987

By Kenichiro Yamamoto, Masaharu Murakami, Toshio Matsuzawa, Yoshiyuki Ikeda

In a series of tests, we examined the dynamic shock resistance of Emulsion Explosive in water and compared it with that of Dynamite and Slurry Explosives. Both the distance between donor and acceptor charges and the delay initiation timing of the acceptor charges were varied. The resistance to dynamic shock varied with the properties of the explosive. In the case of emulsion explosives, there seems to be a certain proportional relationship between the critical detonation distance and the delay initiation timing. Some blasting results with emulsion explosives are described.

Jan 1, 1983

By Anatoliy Yegupov, Vladimir I. Samoylov, Alexandr V. Startshinov

Access difficulties and unique climatic and geotechnical conditions of mineral deposits in permafrost in the Russian Northeast require specific approaches in the selection and use of explosives.

Jan 1, 1992

By Jennifer Ward

The primary objective of this paper is to establish how a low cost, high definition (HD) camera can allow for easy sustainable recordings of blasting operations. The subsequent analysis of each video can be utilized to monitor what type of performance was achieved and aids in improving blasting performance.

Jan 1, 2015

By Dale Preece, Mike Stern, Steve Piercey, Ayman Tawadrous, GC Zhao

The McArthur River uranium mine in Saskatchewan, Canada is the world’s largest high-grade uranium mine. It has employed a freeze-wall system consisting of multiple freeze pipes to control the large quantities of water encountered during mining.

Jan 1, 2011

By Baron Fidler, Dave Lilly, Matt Budin

Cumulative sum (CUSUM) statistical process control methods have been used in many industries to monitor quality control results. CUSUM charts are a method to determine when small changes in data indicate a major change in results. E.S. Page at AT&T developed the method in 1954. In many blasting situations, vibration and air blast readings vary slightly from blast to blast. Whether the change is significant or not can be hard to interpret from the raw data. CUSUM charts can assist in determining whether a major change is taking place and when the change began.

Jan 1, 2009

By Frank Sames

Where applicable, high production benches can improve efficiency in quarrying. Quality control, geological, cost or other considerations might result in the development of quarry benches higher than 30 m (»100 ft) and sometimes up to 60 m (»200 ft).

Jan 1, 1996

By J Lyall Workman, Peter N. Calder

"Presplitting is a technique mines and quarries may use to produce high quality final pitwalls. Damage from backbreak can be minimized, thereby insuring the final pit walls standat the designed angle. Thus costly excess waste removal is avoided. Safety in the pit isenhanced. Control blasting is an essential component of procedures to maintain the stabilityof final pit walls prone to failure."

Jan 1, 1993

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By W. J. Birch, R. Farnfield

All shock-tube based initiation systems have a time lag relating to the propagation velocity of the shock-tube itself. This paper examines the exploitation of this inherent time lag to achieve delay blasting with accuracies approaching that achievable with electronic systems albeit over a much shorter delay range. The system employed consists of a combination of standard shock-tube, plain detonators and various shock-tube branching components. The accuracy of the complete system depends on the scatter in delay time induced by each component. In order to quantify this scatter a series of trials were undertaken to determine the variability for each component. These trials are described along with a detail statistical summary of the data recorded.

Jan 1, 2009