Search Documents

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

By John P. Ashby

Production blasting is a process of destruction of rock masses in order that ore may be extracted. Many open pit operations are faced with the apparently conflicting requirements of providing large quantities of fragmented rock for the processing plant and of minimizing the amount of damage inflicted upon the surrounding pit slopes. A reasonable compromise between these two conflicting demands may often be found by means of simple engineering of production blasts.

Jan 1, 1980

By Dale Preece

In the late 1970’s and early 1980’s substantial resources were devoted to research focused on producing oil from the vast oil shale reserves in the western United States. Since the oil is solidified in the pore space of the shale, extracting it in production level quantities presented monumental technical challenges. Major advances were made in the methods used to extract oil from the shale in large quantities. Extraction methods evolved to culminate in the underground in-situ retorting process. In-situ retorting relied on explosive blasting of the shale to fragment the rock and induce sufficient porosity and permeability for a burn front to propagate through the oil shale. That burn front consumes some of the oil and liberates a substantial portion of it (~30%) for collection and further processing. Oil shale retorting is a blasting intensive process where the entire retort is rubblized in one very large, delay timed blast. Retort 7 in Western Colorado consumed 540,857 lb of slurry explosive to rubblized 348,940 tons of oil shale. Current rock blasting fragmentation predictive capabilities have evolved substantially since these retorts were designed and tested. It is the purpose of this study to simulate the explosively induced fragmentation of oil shale using state-of-the-art computer codes and material models and to infer retort design implications for future development.

Jan 1, 2007

Vibrations are of concern not only for the safety of surface structures but also for the stability of underground openings. A number of parameters affect the intensity of vibration in underground openings due to blasting in adjacent opencast mine viz. total explosive weight detonated in a round, maximum explosive weight per delay, propagating media, depth of cover, RMR of the roof rock, age of the underground openings etc. Although a few researchers have tried to study the impact of parameters stated above, the impact of initiation sequences on generation of vibration in underground openings due to opencast blasting has yet remained untouched. A study was planned to evaluate the impact of initiation sequences on the magnitude of vibration in underground openings due to blasting in opencast mine. Nine production blasts with top and bottom initiations were performed at Samleshwari opencast project in India and eighteen vibration data were monitored in the roof of Hingir Rampur underground colliery in both the initiation sequences. The result indicated that the vibration produced in the underground openings from bottom initiation was lower than that of top initiation.

Jan 1, 2003

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By James H. Redyke

In August, 1980, while finishing construction of the new stack, one of the flues mysteriously collapsed, killing three people and injuring several others. Several months later a British international steeple-jack company was hired to demolish the remaining portion and make a detailed inspection of the balance of the chimney. During this contract almost one hundred core samples were taken from all parts of the structure including the 32-inch thick base. As the result of these tests and the investigation, the Power Company decided to demolish the complete structure. Because of the critical time element, the decision was made to use explosives in the removal of the structure. To give you some perspective as to the size and dimension of the stack, it was 900 feet tall, 80 feet in diameter at the base, and 70 feet in diameter at the top. The two remaining flues were 25 feet in diameter and extended 30 feet beyond the top slab of the chimney. The outside of the structure was referred to as a wind shield. The lower 120 feet were 32 inches thick and the remaining 780 feet were 12 inches thick. The decision was made to prepare and shoot the chimney at the 120-foot elevation because the debris from the collapsed flue was confined in the base section and could not be easily removed. After extensive and costly engineering, we determined it was necessary to construct steel columns to bear on the lower 120-foot section, which would act as a hinge and guide during the dropping of the structure.

Jan 1, 1982

By Eugene Baker

President George Bush signed the Safe Explosives Act (SEA), which amended the Organized Crime Control Act (OCCA) of 1970, into Law on November 24, 2002. As a result of this legislation, new restrictions on who could legally receive or possess explosives in the United States went into effect, resulting in a profound impact on the commercial explosives industry. The law went into effect in two key phases. The first phase, which went into effect on January 24, 2003, resulted in additions to the categories of persons who are prohibited from receiving or possessing explosive materials in the U.S.

Jan 1, 2004

By Yoshihiro Moriyama, Toshihiro Okitsu, Ryouichi Banno

The fracturing composition using the gas pressure generated by the thermit decomposition reaction gives the following performances.

Jan 1, 1995

Previous approaches to pre-split blasting theory have tended to concentrate on the mathematics of dynamic stress wave interaction, whilst only recognizing some interaction with quasi-static stresses induced by expanding gases in the boreholes. However the decoupling used in pre-splitting is specifically designed to reduce dynamic effects to a level that a small degree of radial fracturing is created around the borehole which is emphasized and extended by quasi-static gas effects. It can thus be argued that the process has more in common with hydrofracture than with more conventional use of explosives.

Jan 1, 1984

By Rick W. Bellenie, Ronald L. Woolf

The Gregg River mine is located 40 kilometres (25 miles) south of Hinton, Alberta, approximately 330 kilometres (205 miles) west of Edmonton and lies against the Front Range of the Rocky Mountains.

Jan 1, 1994

By Robert Hivick, Frank Sames

The control of environmental effects, especially blast vibration and airblast, has become a dominating planning criterion for most surface blasting operations. Compliance with existing regulations is generally achieved through constraints in the blast design, or monitoring programs. Commonly, blast vibration and airblast signals are rated and compared by their maximum amplitude and the associated principal frequency. However, this data reduction limits the interpretation of the influence of varying blast design parameters on the vibration and airblast.

Jan 1, 1999

By Calvin L. Cumerlato, David E. Siskind

The Bureau of Mines has monitored structural responses to airblast overpressure produced by munitions disposal at the McAlester Army Ammunition Plant. The Purpose of this study was to determine if the blasting caused vibrations, airblasts or structural responses that could possibly be responsible for cracking or other damage observed in nearby residences. Monitoring took place during a 3-month period at 10 selected residences surrounding the plant. By the end of the monitoring period, nearly 2300 blast-related events had been recorded.

Jan 1, 1994

By Larry Schneider

"0 ne of the incentives that led to the development of non-electric shock tube initiation systems was the desire within the industry to improve detonator safety. And to the extent that nonelectric initiators are immune to the hazards of stray current and radio frequency energy found on normal blast sites, an advancement in safety has been accomplished. However, as a cautionary note, it is important to realize that there are still many hazards associated with any initiation system. While some of these hazards may differ from those associated with electric detonators, others are identical to those associated with any type of initiation system. For instance, contrary to what some uninformedblasters may believe, lightning remains a hazard when using nonelectric initiation as well as electric initiation."

Jan 1, 1995

By Tianrui Xu, Chaohong Liu, Bangqing Ding

The authors were responsible for a series of large scale multiple chamber charge blasts conducted in the granite mountain area for making construction space on the southeast sea coast in China during 1993-1996. This paper describes the blast design and damage control of one mountain blast 320m in length and 280m in width in the vicinity of two wharfs and a dam. In order to obtain better rock fragmentation and muckpile, the explosive charge should be well-distributed in the mountain. The charge pattern, therefore, was designed with mainly 5 rows of tunnel charge in regular terrain in combination with a chamber charge in irregular topography area and the maximum burden was limited to be less than 38m. In order to protect the dam and wharfs the firing sequence was carefully arranged in 29 intervals and the distance between different charges of the same delay to the dam or wharf was taken into account as an additional delay interval based on the difference of p-wave propagating times. The maximum charge fired in an interval was also limited to less than 34t explosives through dividing the larger charge by a stemming deck.

Jan 1, 1998

By Robert B. Hopler

The Hercudet™ non-electric delay blasting cap system has exhibited outstanding performance and economic results in surface work. The versatility inherent in the system, which allows the combining of the built-in cap delays with the tubing delay (i.e.: the travel time of the gas reaction through the tubing), has resulted in outstanding blast results. Examples of blast patterns used, details of the blast design process, and recently-developed methods of use of Hercudet for surface initiation of detonating cord downlines are given in the paper.

Jan 1, 1978

In the office, on the wall to the right of my desk is a large map of the world. Some people stick pins in maps like this to show where they’ve been. If I did that my map would be a mess and look like a pin cushion. I was so fortunate to have been able to see how people live and blast in other parts of this beautiful planet. We l l , maybe some parts weren’t so beautiful and maybe some parts that were beautiful were hell holes for those living t h e re . Every time I re t u rn to the good old US of A, I say a small prayer in thanks for having been born and raised in a land of freedom and plenty. So many places and people have not been so blessed.

Jan 1, 2004

By Roger L. Keller

This paper covers the design and test blast procedures for several drop shafts and edits leading to the completion of a recent Rochester Pure Waters Expansion Project . Due to the projects "in-town" presence, and its close proximity to many sensitive vibration sites, very stringent ground vibration limitations and guidelines for blasting were places on each site.

Jan 1, 1991

By Gordon Revey

The challenge of managing blasting risk, types of risk, public perception, and a system for managing risk were covered in the first part of this article in the May/June 2000 issue of the Journal of Explosives Engineering. This final part of this two-part series provides a method for identifying specific blasting risks and reviews the importance of community relations.

Jan 1, 2001

By Jhon Silva-Castro, Russell Lamont

Understanding the behavior of materials subjected to high strain rate conditions is of fundamental importance to the mining industry. Several stages of the mining process involve high speed loading rates including blasting, scraping, comminution, etc. Technical comprehension of how rocks deform, fracture, and fail under these loads is a fundamental first step required prior to any serious attempts at optimization of the energy utilized for pertinent activities in the mining process. A Split-Hopkinson Pressure Bar (SHPB) was designed and constructed at the University of Kentucky to study the dynamic properties of various types of rocks.

Jan 1, 2017

By Denard A. II Brandt

Today I would like to share with you some blasting practices used in the thick coal seam mines of Northeastern Wyoming. I will begin by giving you a general overview of a thick seam coal operation at The Carter Mining Company's Rawhide Mine. I will then discuss the blasting procedures used at this operation. The Rawhide Mine is one of 13 mines operating in the Eastern Powder River Basin of Northeastern Wyoming. Approximately 23 billion tons of recoverable coal lies in the Powder River Basin. The Rawhide Mine is currently producing approximately 8 million tons per year. Rawhide is the 9th largest coal mine in the United States according to 1982 production. We also received the 1982 Sentinels of Safety Award for being the safest surface coal mine in the United States. Rawhide's permitted capacity is 24 million tons.

Jan 1, 1984