Search Documents

By Kunihisa Katsuyama, Yuji Ogata, Takuya Taguchi, Toshinori Arikiri, Yuji Wada, Kiyoshi Hashizume

The impact sensitivity of hot emulsion matrices was examined to investigate the safety assessment in the emulsifying equipment which forms the emulsion matrix in a water-in-oil type emulsion explosive. The sensitivity could not be evaluated by the small fallhammer test device commonly used in Japan. Therefore, a large fallhammer test device was used. It was confirmed that an explosion, a decomposition, or a no-reaction took place according to the degree of the impact. When a decomposition took place in the hot emulsion matrix, the behavior of it was investigated further by a DDT test. It was found that a decomposition, or a no-reaction occurred according to the degree of confinement.

Jan 1, 1997

By Shih Wen Wang, Ronald R. Rollins

A blast casting model is proposed to predict the burden velocity in bench blasting. This blast casting model is the first theoretical model that 1) explains the throwing procedures and mechanisms, 2) uses the explosion pressure as the primary source in throwing rock fragments, 3) applies them to field conditions successfully. Also the predicted burden velocities are based on the rock properties, the explosive properties, and the drilling and initiation patterns. This blast casting model is programmed into a computer software "ROCKFRAG". The comparisons between "ROCKFRAG" predicted values and two field test data are in good agreement.

Jan 1, 1992

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By M J. Ball, R Watt

ICI has developed a new electrical shotfiring system which has markedly improved safety features and operational advantages over existing initiating systems. The development of the 'Magnadet' Electric Detonator and the related product 'Magna' Primer were described in a paper presented at the 1981 S.E.E. Annual Conference. Since then the system has been adopted in many different applications and conditions around the world. The present paper describes these applications, the experience gained and the more recent developments which have taken place.

Jan 1, 1982

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By Ronald Joseph

Windows-based automated blast loading systems have long being conceptualised and never really taken off in the surface mining sector. However, with the introduction a windows-based automated blast loading and reporting system onto the Mobile Manufacturing Units (MMU’s) at Debswana Diamond Company operations in Botswana in August 2004, a project to automate blast loading (charging) and reporting ensued. This work was pioneered over three phases at Debswana’s Jwaneng Diamond Mine by African Explosives (Botswana) (Pty) Limited as part of the African Explosives Limited’s (AEL) integrated-mining (i-mining) concept. The first phase of the project involved the blast reporting system, at which time an average amount of explosives were loaded into all blastholes and all blast loading information was saved to a Microsoft Access 2000 database on the MMU computer. The second phase of the project, which ran until the end of the second quarter of 2008, involved manual blast plan loading and reporting system using flash disks, and the third phase which was installed and commissioned in the third quarter of 2008 and is currently operational at Debswana’s Jwaneng Mine, involves the automated blast loading and reporting system via Wireless Local Area Network (WLAN). This system is now routinely used to achieve operational and mining efficiency goals at the mine with respect to blasthole charging and blasting, and this paper briefly summarizes the status of this project at Jwaneng Diamond Mine where this technology is currently being monitored and also illustrates the positive mining impact that this innovation brings to the mining operation, both from an economic and efficiency perspective.

Jan 1, 2009

By D T. Froedge

In 1972 the Kentucky State Legislature enacted House Bill 625 which was known as the Kentucky Blasting Law. This law was enacted primarily to stop problems associated with surface mining, but when it was enacted all industries using explosives were included. The bill was assigned to the Department of Mines and Minerals which created a Division of Explosives and Blasting. At that time, this division only had regulations concerning blasting. One should make a distinction between blasting regulations and other explosive regulations. Blasting is the actual use of explosives, the control of the blasting operation, how much is used, at what distances to buildings, the yardage, and other actions associated with the detonating process, explosives regulations generally including safety to the personnel and the storage of explosives.

Jan 1, 1977

By R Yang, P D. Katsabanis, W F. Bawden

Understanding the mechanisms which are taking place during the propagation of a stress wave generated by an explosive charge is of high importance in the detection, characterization and prediction of blast induced damage to the rock. Vibrations caused by the detonation of an explosive are suspected to contribute significantly to the extension of the damage zone. Vibration monitoring close to a blasthole is a relatively new field of research, the hindrance being the scarcity of transducers capable of sustaining extreme accelerations without damage. This paper focuses on the vibration monitoring aspect of a blast induced damage study; the experiment took place at Queen's test site and was meant to record near-field vibration as close as 1 m from 100 mm diameter blastholes.

Jan 1, 1993

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By C. Pelley, S. Kelebek, G. Kunzel, P. Katsabanis

Small blocks of granodiorite have been subjected to blast loads from a single borehole and from a series of boreholes detonating at various timing intervals. The damage of the blocks was assessed through P-wave velocity monitoring, measuring the change of the point load strength index of the rock after dividing the large blocks into smaller ones and measuring the work index of the material at different distances away from the blasthole. Numerical modelling with the AutodynTM code enabled visualization of damage. It was shown that damage is optimum at a small delay time between successive holes while it drops rather drastically after this point.

Jan 1, 2003

By Calvin J. Konya

The Woodville Lime and Chemical Company Limestone Quarry is located in Sandusky County, Ohio. Fifty years ago, when quarrying began, it was situated approximately two miles from the town of Woodville. Today new houses border the quarry property within 1,500 feet of one of the working faces. During the past two years, the operation has systematically changed the blasting program to achieve better fragmentation, lower costs, and to maintain good relations with the local property owners. This paper will discuss systematic changes made in the blasting program to increase productivity and reduce costs.

Jan 1, 1977

By Courtney W. Shea, Dennis Clark

Reckless blasting can have tragic consequences: The death of an innocent traveler, the financial demise of a coal company, and even criminal prosecution. In June 1993, a Tennessee coal mining company was blasting to loosen overburden at its surface mine. The mine was located immediately adjacent to the right-of-way of the northbound lane of Interstate 75. The approved permit included special precautions to be taken when blasting in the area closest to the interstate, including monitoring traffic so as to blast when the northbound lane was clear.

Jan 1, 1998

By Ingvar Hansson, Bjorn A. Jonsson, Bernt Larsson

In the Kiruna Research Mine, Sweden, four large open stopes have been mined, leaving intermediate piIlars and crown pillars. At the final stage of mining mass blasting of the crown pillars above two of the stopes was carried out. The crown pillars contained some 290,000 tons of iron ore. In the mass blast a new initiation technique was used, utilizing the new non-electric system NONEL ? UNIDET. The blasting technique including vibration control is described. The mass blast resulted in high recovery, good fragmentation and low vibration levels.

Jan 1, 1986

By James Rowland, Marcia Harris, Richard Mainiero

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NO x ). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed.

Jan 1, 2007

By Sarma S. Kanchibotla

In overburden cast blasting the explosive energy is used to move a significant percentage of overburden from the high wall to the spoil pile thus reducing the amount of material to be handled by machinery. However, the obvious trade-off between the extra explosive energy in the cast blast versus reduced dragline effort is complicated by an increased risk of damage to the underlying coal. This damage may not be obvious but inevitably leads to reduced coal recovery and may negate much of the benefit sought from cast blasting.

Jan 1, 1999

By Romel Villanueva L.

"Peru does not produce ammonium nitrate; nevertheless it is a large consumer of both, porous prill (PP) and high-density (HD) varieties. Explosives cost is an important preoccupation in Peru, due tofluctuations of the imported ANFO grade Ammonium Nitrate (AN). The use of Gasified Emulsion (GE)-manufactured with much cheaper HDAN- has become an alternative to reduce such costs. However, some problems were reported in the application of pure GE, including explosive percolation in highly fractured rock and lack of sensitivity by the effect of hydrostatic pressure in very deep holes. It was, hence, proposed to have an explosive based on GE too, but more robust and capable to keep the shape of the explosive column into the blast hole, by minimizing the leakage into the cracks. This could be achieved by adding limited amounts of lower priced HDAN, at the same time of providing gas pressure benefits. Other alternative is to add a low-density material, such as polystyrene prills, into the GE, although it reduces the explosive energy. The chemical gassing controls the density of GE, thus it can be obtained a wide range of densities."

Jan 1, 2016

By T. Bajpayee, G. Mowrey, D. Ingram, T. Rehak

Blasting operations are an essential element in the recovery of our Nation’s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining .operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining.

Jan 1, 2001

By Alastair Torrance, Braden T. Lusk, MinGi Seo, Gary Cavanough

Velocity of Detonation (VOD) is the most commonly used method to determine explosive performance as VOD is a function of the confinement (ground conditions) density and composition of the explosive. Techniques used to measure VOD include resistance wire, time domain reflectometry, simple start stop and fibre optic methods. All these approaches require a cable of some sort to be inserted into each blast hole being monitored and the holes to be fired in a specific sequence. It is time consuming and fairly technical to position the cables correctly to gather the data from each hole. It slows down the hole loading process and increases the number of people on a bench at that time. The equipment and cable limits the measurements to a few holes, typically 5 or less, that are in close proximity. These measurements can generate useful information about the monitored holes but does not provide a full picture of how the explosive is performing across the whole blast and whether any change in performance is noted with changing ground conditions or confinement.

Jan 1, 2019

By Jack Eloranta

Transmission of sound through the atmosphere is affected by local conditions. Anecdotal accounts of the sound of cannon fire traveling great distances go back to the Civil War. The Royal Society published a paper near the turn of the century concerning the reports from the cannons fired in London at the funeral of Queen Victoria. Early computers were used by the U.S. Army at Aberdeen in Maryland in the 1950’s to model airblast problems during munitions demolition. Today’s blaster has to have access to weather information beyond a simple local forecast. Surface winds, winds aloft and temperature profiles have a dominant role in neighbors reaction to blasting. Many ground vibration complaints are really airblast complaints. Blasters who maintain ground velocities under . 1 inches/ second are often perplexed by complaints from distant neighbors, even when local monitoring shows airblast to be under 110 dB. This paper will help the blaster identify warning signs of high airblast conditions.

Jan 1, 2000