Search Documents

By A. S. Tawadrous

Fines are produced in any blasting application. Depending on the application, fines may or may not be a desirable product of the blast. In most quarry and construction applications, fines are considered an undesirable product since it does not constitute a sellable product and there are costs to the operation for disposal. On the other hand, in most open pits fines do not represent as much of a problem since the ore has to be crushed and ground after being blasted. Therefore, fines in such operations may reduce the energy consumed in the downstream operations.

Jan 1, 2012

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026

By R. Hazael, R. Alford, R. Critchley

The ability to compare explosives is fundamental. Numerous methods are used and while simple conversion factors are often used, the use of TNT Equivalency (TNTe) is not a simple subject as explosives exhibit very different equivalencies depending on whether the pressure or impulse are being considered as well as other conditions. The scaled distance has been found to have a significant effect on the TNTe but due to the difficulty of taking measurements at very close ranges, no TNTe have been quoted for charges in direct contact (Z=0). This paper describes the use of a ballistic pendulum to measure the impulse from contact charges and presents some surprising results that require a two-stage propulsion, as originally described by Backofen, to be explained.

Jan 1, 2024

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer

The environmental problems such as vibration, and air blast are often faced, and discussed on mining, quarrying, civil constructions, shaft-tunnel, pipeline, and dam operations where blasting is inevitable. It is necessary to establish national standards towards to minimize the environmental problems induced by blasting and judicial matters in our country as it is in USA, EU countries and the other developed countries. This necessity and the obligatory of accepting the European Union criteria for Turkey that has started the procedure of joining to EU emphasize the importance of this study. In other words, the establishment of a particular national standard related with this subject is inevitable for Turkey. This will be possible only by studying, applying scientific methods and techniques by the experts.

Jan 1, 2010

By BruneJurgen F., Richard C. Gilmore, Matthew Schreiner, Ray Johnson

Explosive pockets of methane-air mixtures accumulate in underground coal mines and, when ignited, produce an air-blast wave that can disturb combustible coal dust on the floor, roof, and ribs. To prevent explosions, the coal dust must be continuously diluted through application of inert rock dust, usually powdered limestone. Application of powdered dust process creates a respiratory nuisance downwind, where miners cannot work until the dust settles. Rock dust suppliers have developed wet and foam applied products to reduce the nuisance and limit the interruption to mining during dust application. To test the effectiveness of these alternative dust products, researchers at the Colorado School of Mines (Mines) have constructed a full-scale explosion test drift located at the Mines Edgar Experimental Mine (Edgar) to study the dispersibility of different rock dust applications. This paper examines the use of Pentaerythritol tetranitrate (PETN) detonating cord to produce controlled air-blasts that simulate methane-air explosions. The air blasts are generated with curtains of detonating cord that produce shockwaves with wind speeds between 30 to 70 m/s (100 to 225 fps) depending on the length of 5.3 g/m (25 grain/ft) detonating cord used. These velocities represent the minimum air speeds required to trigger propagating coal dust explosions. Researchers have conducted 40 test blasts with various lengths of detonating cord. Results show the two primary waves and two reflected waves each decaying into airblast waves with overpressures of 14 to 27 kPa (2 to 4 psi). Pressures were recorded with commercial piezoelectric transducers and custom-built, bi-directional probes to record the total and dynamic pressures of the wind generated in the explosion. Researchers were able to generate consistent and repeatable wind speeds and air-blast durations sufficiently similar to a methane-air explosion to study the dispersibility of various rock dust products and application methods

Jan 1, 2019

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Frank Sames, Brad Terhune

In many construction projects and in most quarrying operations drilling and blasting remains the only feasible method of loosening rock in the removal of rock or overburden, the development of the quarry and in the production process of crushed stone. Often, a blasting plan is required for the project or the quarry’s permit with primary concerns over safety and site security, and compliance with environmental regulations or standards. From this plan, a blasting program has to be developed considering the varying requirements of production, the advance of the mineral extraction and the environmental impact. The actual blast design requires a planning and optimization process. This optimization process is driven by the blasting technicians/engineers, project or mine management and often by community concerns. The blast design process comprises the selection of blast parameters, including the explosives, and the actual layout of the blast. Design tools and controls range from conventional methods based on established blasting practices to advanced design tools or computer models. Blast monitoring and evaluation can also range from empirical to advanced blast assessment. The data and information from each blast or a series of blasts can further be used in the optimization process. Its success depends upon recording the data, the timely transformation of the data to relevant information, and the development of process oriented knowledge. The elements of the blast design process are summarized and described with examples of state-of-the art engineering controls. The reporting and monitoring of individual blasts is discussed with respect to data management and information systems. A conceptual overview of the components and interfaces of a blasting program is given and discussed on the background of technical, management and community concerns.

Jan 1, 2004

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By M. Hagfors

When establishing an underwater testing site for the energy measurements of the explosives, the dimensions of the measuring pool have to be measured to find out what is the maximum weight for the test charge. Secondly one has to decide the distance between the pressure gauge and the shooting point. Thirdly the pool has to be calibrated because of the reflections of the explosions by measuring the bubble periods of the calibration charges. The calibration shots can also be used to estimate the minimum weight of the explosive charge for the reliable energy measurements by calculating the shock, gas heave and total energy values and their standard deviations.

Jan 1, 2007

By Nikolaos Petropoulos, Ulf Nyberg, Ulf Stenman, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature.

Feb 1, 2020

By Neal Lee, Braden T. Lusk, Brendan McCray

"Selection of a blasting agent for optimum performance is based on many variables. Often, a decision is made with regard to product cost and field testing. Defining optimum performance can be difficult, since downstream effects of fragmentation on loading, haulage, processing, and energy consumption are not immediately clear. Many operations are beginning to optimize their blasting programs “on the bench,” by utilizing information generated downstream at the loader and/or crusher. During the evaluation of a blasting agent, factors such as velocity of detonation, gas production, and sensitivity are typicallyconsidered. Alternatively, brisance (“the shattering power of an explosive material distinguished from its total work capacity”1) is not. Brisance affects the immediate area surrounding a borehole. Fractures produced here during the shock phase of detonation are believed to have an important effect on rock movement and fragmentation. "

Jan 1, 2017

By Rachel E. Gooding, George C. Emmett, David R. Bradley

The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T) is using a probabilistic risk assessment (PRA) approach to evaluate the risks from terrorist use of explosive materials against the Homeland. A similar approach is currently being used to evaluate the risk from terrorist use of chemical, biological, radiological and nuclear materials.

Jan 1, 2017

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By K. Best, D. Conn

The US Army Corps of Engineers KY Lock Project in western Kentucky presented the blasters and vibration consultants with a set of unique challenges. The blasters on this project were faced with difficult geology and joint set orientation and sequencing of blasts opposite from what the explosive engineer/blasting specialist had recommended. Combining these issues with strict vibration and air overpressure specifications, blasting as close as 7 feet (2.1 meters) from a new lock wall, site topography that influenced the air overpressure, limitations on seismograph geophone placement that led to anomalies in seismograph recordings; surprising lessons were learned by everyone involved in the project and it is the authors’ goal to share this valuable information with everyone in the blasting industry.

Jan 1, 2024

By Italo Onederra, Miguel Araos

"In order to characterize non-ideal explosives, the explosives industry rely on unconfined velocity ofdetonation tests and where possible underwater pond tests. The information obtained from such tests isquite helpful, however it cannot tell us much about the dynamics of the detonation reaction process. The detonation process has been studied for ideal explosives and the reaction zone length have been measured. However, for non-ideal explosives, that type of information is not available. Therefore, the primary aim of this work was to capture the detonation process of a non-ideal explosive using high speed video camera to determine the zone length."

Jan 1, 2017

By Jorge Cárdenas, Piero Mejía, Diego Gamarra

The present case study details the solution to a complex situation in a mining operation, involving the challenge of expanding the tailings storage facility in high-criticality areas adjacent to electrical rooms that provide continuous power to the entire mining process, including water pumping and drainage systems. For this purpose, blasting is required to prepare the construction areas for the new expansion facilities. Upon deciding to proceed with blasting, a comprehensive engineering assessment was conducted to ensure operational continuity without impacting the process, while generating sufficient fracturing in the rock mass to allow extraction with auxiliary equipment. Support from specialists through the Technical Assistance area was requested, and a detailed evaluation was carried out through advanced studies. Field vibration studies were conducted to define attenuation models and characterize the rock mass in the sector. With this information, simulations were carried out using predictive and probabilistic models with Monte Carlo methods to select delay charges and optimal timing for reducing vibration levels and increasing frequency levels. With these measures, the three blasts conducted near the Gas Insulated Substation room, which had distances ranging from 30 to 100 meters, produced the following results: • Vibrations; The three blasts conducted at distances of 100, 30, and 50 meters recorded vibration values of 5.3, 40.2, and 9.5 mm/s, all of which were below the maximum vibration level of 50 mm/s set by the projects area. According to the USBM RI8507-OSMRE standard, all values for Peak Particle Velocity (PPV) and frequency were below the permissible limits. • Flyrock; Through filming and post-blast inspection, it was confirmed that the ejections were within the safety zone. • Fragmentation; The results obtained showed a maximum overbreak size of 1.5 meters, allowing the broken material to be moved effectively.

Jan 21, 2025

By B S. Petri, N T. Rouse

Underground limestone mines generally lack air pressure monitoring procedures and instrumentation guidelines. The blasting industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground mines. This became apparent during the development of a new underground limestone mine, where overpressure levels from production blasting needed to be estimated. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting. Therefore, a study was conducted to (1) identify and review any published studies for data that may be applicable, (2) identify the appropriate equipment required to record the overpressure levels, (3) determine the proper procedures for setting up the equipment and recording overpressure, and (4) provide an understanding of the nature of the air overpressure in a developing mine.

Jan 1, 2014

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025