Search Documents

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By G. F. Revey

When rock blasting occurs near new concrete of varying age, engineers representing project owners often express concern that vibration from the blasting will crack nearby concrete. Regulations and/or specifications for civil construction projects usually include particle velocity vibration limits intended to protect concrete. In some cases specified limits are unreasonably low and needlessly restrict and increase the cost of excavation work. This paper discusses how methods of predicting resulting flexural strains caused by blast-motion can be used to develop safe and reasonable PPV limits to protect new concrete. Three case histories demonstrating how these evaluation techniques were used to establish higher PPV limits designed to protect concrete of various structural condition are also presented.

Jan 1, 2006

By Kfw Eick

The paper describes the use of the Nonel millisecond delay blasting system in narrow, deep, tabular ore bodies and briefly describes the standard stoping method as used on Harmony Gold Mine and compares this with the new Nonel short panel system.

Jan 1, 1990

By D Vrkljan, Z Ester

There was no use of emulsion explosive at Croatia till 1997. Several attempts have been done to bear out the economical and technological affordability of applying the emulsion explosive for open pits and to make the contractor familiar with characteristics of emulsion explosive exepiting experimental blasts series at more open pits on different kinds of rocks. Testing the efficiencies of emulsion explosive there has been applied the original method for linear enlargement of burden of Sc.D. Josip Krsnik’s from Mining, Geology & Oil Faculty, University at Zagreb. The method of linear burden’s enlargement, in distinction from other methods concerning these problems, has been carried out in situ, under real exploitation conditions whereas the physical-mechanical rock’s features, geological conditions, bed relations and rocks’ structure influence the blast efficiencies. On such way, by mean of method the precise boring and blast sizes will be reached for each kind of rock and geological structural bed’s conditions referring to specific explosive type. The technical-economical analysis indicates the most favorable explosive type for specific bed.

Jan 1, 1999

By Tom Donnelly, Roger C. Ilsley

Remote telecommunications seismographs were used to monitor blast vibrations at two historic structures in Cedarburg, Wisconsin during adjacent sewer line construction. The purpose of the vibration monitoring program at the historic structures was to maintain blast vibrations below limiting tolerances established by the Wisconsin State Historic Society.

Jan 1, 1991

By David E. Siskind

In the early 1980's, the Bureau of Mines published four reports of structural response and damage from surface mine blasting, vibration monitoring, and analysis methods. These findings replaced simpler and less restrictive Bureau criteria dating back to 1962 for ground vibration and 1943 for airblast.

Jan 1, 1991

By John Watson

Overview: Intro and Product Use Trends ?? Packaged Explosives ?? Bulk Explosives ?? Initiation Systems – Conventional Initiation Systems – Electronic Detonators ??Q&A

Jan 1, 2006

By C H. Dowding, P W. Linehan

Many of the technical and non-technical or human problems associated with blasting can be minimized through a proper preconstruction test-blast program.

Jan 1, 1986

By Robert F. Dexter

This paper discusses the Federal requirements of this regulation for the importation, manufacture, distribution and storage of explosive materials. The interstate or foreign commerce in explosive materials, licensing of manufacturers, importers and dealers, issuance of permits, the conduct of business by licensees and operations of permit tees and the storage of explosive materials.

Jan 1, 1975

By Jerry R. Wallace

A systematic, team approach to pre-blast and on-going problem solving contributed to the successful completion of this indoor industrial construction blasting project.

Jan 1, 1995

By Brett Pielstick, E Emery Gray

"Construction of the new Acosta Bridge in downtown Jacksonville, FL required the removalof an historical center lift span bridge once one_half of the new bridge had been opened totraffic. This paper discusses the potential problems faced with the demolition phase of the projectas observed by the CEI (Construction Engineering Inspection) and the blasting consultants"

Jan 1, 1993

By C Robert Scott

Yes - We have figures on Explosives Manufacturers ! But, on the 500 or 600 explosives contractors, unless you happen to specialize in shooting oil wells, we have no numbers. As you know, the Insurance Industry lives on numbers, the larger the better. They collect the amount of premiums and losses on each line of insurance they write.

Jan 1, 1980

By E Emery Jr Gray

A need for more delay periods other than those normally manufactured throughout the explosives industry rarely occurs. This paper will discuss one such incident from an analytical view through practical application.

Jan 1, 1976

By W. Reisz

Dealing with misfires can be one of the most difficult and serious issues that blasters must confront. Most of us will - at some point, have to deal with a misfire situation.

Jan 1, 2009

By Hu Wenjun

This paper changes the section of copper of copper to aluminum adapter bar into aluminum plate covered one face or double face with copper coat, and changes the conductor material of knife switch, fuse box, plug and socket into steel plate covered one face or double face with copper plate, and manufactures the composite (two layers or three layers) metal plates by means of explosion welding with the plates installed horizontally. Introduced in this paper are the blasting designing technique, manufacturing process and the electrical performances of the explosion bonded products. Besides, this paper presents the designing and manufacturing technique of cumulative charges and their time detonating units for cutting off the retired nuclear submarine pipes. Experiments on cutting off the stainless steel pipes by cumulative flow and on the time detonation are made. Keywords: explosive welding, electric, explosion bonded products, retired nuclear installation; pipe; blasting cutting; cumulative charge; time detonation

Jan 1, 2000

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By Eric R. Achelpohl

The paper follows the introduction of a college student into the explosives industry. The opportunity of experiences from classes and work at the University of Missouri-Rolla, along with summer internship experiences are highlighted.

Jan 1, 1998

By J MacPhail, H Gardner

This paper discusses reasons why users of rotary air blast hole bits encounter premature bit failure due to bearing failure. It also discusses a lubrication system designed for rotary rock bits to combat bearing failure.

Jan 1, 1996

By R R. Vendebeek

The continuing evolution of explosives has most recently introduced emulsion explosives and heavy ANFO's to the market place. An explosives engineer has a multiplicity of explosives to choose from: dynamites, slurries, water gels, emulsions, ANFO's, and mixtures of some of these products.

Jan 1, 1987

By James L. Wilcox, Douglass P. Bacon

As the U.S. Environmental Protection Agency (USEPA) and state regulators increase the stringency and enforcement of regulations concerning emissions produced by open-air detonation of energetic materials, research must provide the means of obtaining emissions data. The BangBox emissions testing program established the technical foundations for emissions characterization which have been accepted by the USEPA and other regulatory agencies; the technical issues remaining are nettlesome and require new approaches in test procedures.

Jan 1, 1996