Search Documents

By Andrew Palangio, Blessing Taiwo

Understanding rock mass structural features is essential for optimizing blast design, highwall control, and evaluating post-blast performance in both surface and underground mining operations. This paper presents a comprehensive methodology utilizing image-based structural mapping to accurately characterize geological discontinuities including joints, faults, and lineations captured from both terrestrial and aerial imagery at varying scales. Key structural parameters such as joint orientation, spacing, and apparent in-situ block size are extracted to understand rock mass classification and enhance blast design inputs with greater geotechnical precision. The study introduces a significant enhancement to the existing discontinuity assessment algorithm by integrating a deep learning-assisted detection process. This improvement enables more accurate, quantitative and consistent identification of pre-existing cracks and surface features across complex bench free faces. The enhanced system facilitates better evaluation of how structural features influence blast fragmentation, energy distribution, and slope stability. A case study from a limestone quarry illustrates the use of a derived comminution factor based on the relationship between joint-controlled pre-blast block sizes and post-blast fragmentation to evaluate blast performance and optimize future design strategies. The results highlight the value of structural analysis in reducing overbreak, minimizing underbreak, and improving fragmentation predictability. This paper emphasizes the importance of integrating structural assessments into the blasting workflow to enable a more data-driven, geotechnically informed, and performance-optimized approach to modern blast design and evaluation.

Jan 26, 2026

By Alastair Torrance, Gary Cavanough

Approximately 1.5 million tonnes of ammonium nitrate are transported annually across Queensland, Australia—equivalent to nearly 100 truckloads per day. This is in the form of both AN prill and ammonium nitrate based emulsions (ANE). In a recent incident, a collision involving an ANE tanker resulted in a detonation that caused extensive blast-related damage and led to the closure of a major highway. Had this event occurred within a populated area, the consequences would have been catastrophic. For over a century, investigations into the causes of such spontaneous detonations have been inconclusive. A recently completed industry supported research project has made a pivotal discovery: a surface reaction mechanism leading to hydrogen generation has been identified as a precursor to detonation. If sufficient hydrogen accumulates and subsequently ignites, it can release enough energy to initiate the detonation of bulk ammonium nitrate and ANE. Controlled experiments conducted during the project successfully demonstrated hydrogen-driven detonation events. Previous work by Proulx and Scovira, presented at the 2000 ISEE Conference, described spontaneous detonations in hot, reactive ground and the mitigating effects of buffered emulsions and ANFO. Building upon their observations, this study reproduces similar incidents under laboratory conditions, confirming that hydrogen generation also results from reactive ground interactions. Importantly, the findings challenge traditional assumptions, demonstrating that ammonium nitrate and ANE detonation in reactive environments does not require an ignition temperature threshold, confinement, or a classical chemical decomposition pathway.

Jan 26, 2026

By Rolf R. Schillinger

It is established to an increased extent that the basic questions about raw material extractions deal with water, dust, noise and vibrations. If it has not been definitely proven that these points won?t lead to excessive environmental strains, attempts at any explanations will meet with disapproval in advance. In order to answer the basic questions about dust, noise and vibrations quality management becomes most important, particularly with respect partly unavoidable emissions of production processes. The specific questions have to be answered within the context of good blasting practices, latest discoveries of the explosives industry, and by use of a Blasting Works Quality- Management, which includes both production quality and Risk-Management. The paper shows a practical way to work out a Quality-Management Program for companies involved in blasting activities.

Jan 1, 2002

By Edward J. Walter

A vibration record is a complex of motions resulting from a combination of direct, reflected and refracted seismic energy that originated at a blast source. Multiple hole blasting using delays further complicates the motion in that overlapping of seismic wave trains may occur when delays do not fire in the programed sequence. This can result in variations in amplitude, frequency and wave-1ength of the vibration. Amplitude may be doubled, frequency may oscillate between the highest and lowest frequencies present and wave-length may approach doubling of the longest wave-length present. These effects can present serious problems to conducting a safe blasting program since increased amplitudes and lower frequencies present higher damage potentials for structures. The development of these effects is described and illustrated graphically to show how these effects can occur.

Jan 1, 1989

By John W. Kopp, David E. Siskind

Over 4 billion pounds of commercial explosives are used by the U.S. mining industry every year with an excellent and improving safety record. However, accidents involving explosives are seldom minor. They produce a disproportionate amount of fatalities compared to other mining activities, as reflected in the relatively high severity rates. The U.S. Bureau of Mines (USBM) has been analyzing blasting accident data obtained from the Mine Safety and Health Administration (MSHA) to determine the most frequent causes of mine blasting accidents, examining trends in these accidents, and identifying areas of needed research. This paper is an update of three previous blasting accident studies conducted on 4-year intervals by the USBM and published in 1983, 1987, and 1991, and is based on a total of 869 blasting accidents.

Jan 1, 1995

By W C. Burkle

A rather common observation over the last several decades at least has been that rock or ore properties influence blasting results more than does the explosive type that has been used in the blast. It we accept that premise than it is held here that the material to be blasted should receive even closer attention as to its properties. Several years ago, Dr. Richard Ash published papers that pointed out the rock properties that mostly influence blasting. These principles are given attention in this paper. We have gone somewhat further - or lets say expanded this subject in regard to the role of rock structure in open pit blasting. Though open pit work is given some prominence, we believe that much can be observed and applied to underground mining.

Jan 1, 1979

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

Jan 1, 2002

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

By G G. Paine, C V. B Cunningham, G Harries

The companies of the ICI Explosives Group have successfully used a wide variety of internal computer codes including BOBCAT, KUZ-RAM, ICRAX, XPLODE, BLEND, 3CRACK, MICBLAST, DETON, etc. In recent years the extensive experiences across ICI have been combined into a single compatible model engineered to worldwide technical service and customer needs for the prediction and assessment of blast results.

Jan 1, 1987

By James R. Houston, Wendel Clay Chaffin, John Loviza

During the spring and summer of 1993 the largest pipeline in Tennessee was installed as part of the upgrading of Nashville's sewage needs through the year 2035. This new 3.3 million dollar outfall project is able to carry 330 million gallons of treated sewage water daily. Special projects required special equipment as this project was safely and quickly installed.

Jan 1, 1995

By Charles Clark, Mark Mukhija, Jaime Klein

Comminution – the reduction in size of solid materials – is the most energy intensive component of the mining process (Bauer, 2015). It is estimated that comminution consumes around three percent of all electricity generated in the world (Ceecthefuture.org, 2017). On an energy equivalent basis, downstream processing consumes six times more energy than drilling and blasting (Kanchibotla, Sarma et al., 2014).

Jan 1, 2018

By K. Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics (hereafter “the company”) developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits

Jan 1, 2024

By Jonathan Peck, Doug Pollitt, Malcolm Scoble

Over the past 5 years the Department of Mining and Metallurgical Engineering, McGill University, has been involved in the performance monitoring of both percussive and rotary drills. Studies conducted in open pit coal and iron ore mines using microprocessor-based research and commercially available instrumentation resulted in the monitoring of at least 6 performance parameters while drilling vertical production blastholes.

Jan 1, 1991

By Jackson R. Pressley, Bruce Vandenberg

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1992

By Syed Haq, Kyle Optt, David Campo, Doug Anderson

Limitations on allowable levels of vibration from construction activities generally consider either annoyance or damage. While activities such as drilling and roller compaction primarily create annoyance, the major concern for blasting is usually damage. Many years of research have developed correlations between peak particle velocity and either threshold or structural damage. We emphasize the term “correlation” for two reasons. First, peak particle velocity is only a single-valued representation of a vibration waveform, and does not characterize it completely. Second, a given peak particle velocity by itself, even a particle velocity waveform, will not damage anything – strain does. Why not measure strain all the time? Strain is very localized, and can vary substantially over short distances, so choosing the appropriate strain measurement can be difficult. Measurement of strain is appropriate when either the behavior of a specific structural element is needed, or the overall response of a structure can be adequately represented by a well-selected strain measurement. We will discuss the appropriateness of both particle velocity and strain as deformation and damage descriptors, in general. We will also describe a specific case history, from a tunnel project in New Jersey, correlating strain with peak particle velocity. Finally, we will make recommendations for the choice of measurement type for some common situations.

Jan 1, 2004

By Brian Lewis, Reinhold Daykin Schnell

Blasting specifications and guidelines are very important aspects of detailed project specifications covering any scope of work (SOW) that involves explosives and blasting procedures. A lot of larger construction or tunneling projects require some degree of project specifications for the entire scope of work on such project, including blasting specifications. It is important that all blasting specifications effectively and accurately address all explosives and blasting concerns associated with the SOW for such project. This includes safety and security, required personnel and their associated responsibilities, procedures and applications involving explosives, blast design and planning, blast monitoring and reporting, quality assurance and quality control, and local, state, and federal regulations and limitations. With the of wide range of information required in blasting and overall project specifications along with the risks associated with work involving explosives, it is also important to ensure qualified personnel are involved in interpreting or compiling and approving any blasting specifications and guidelines. The purpose of the following paper is to explore and present the basic information, as summarized above, that should be included and considered in the creation of detailed blasting specifications and guidelines. Detailed information is presented in specific relation to a potential bid package that would be compiled for a construction or tunneling project requiring protective or high-profile blasting.

Feb 6, 2023

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By Rowland Jones

This type of quarrying is very much different from that of established quarries in developed countries, demanding somewhat unorthodox techniques to produce the variety of materials required. The demands on the resourcefulness of-the quarrymaster can be very testing, and produces quite a different breed of individual than what is normally met in managerial status in quarries of developed nations.

Jan 1, 1977

By Dave I. McGregor

The Multiple Raise Round Blasting Technique (MRRBT) is a safe, efficient, cost effective method of blasting thee will use existing mine personnel. The MRRBT, developed from the conventional 'drop raise method' style of blasting, can be used for most raise mining applications. Current results using MRRBT indicate no upper limit for the maximum length that a raise can be blasted.

Jan 1, 1994

By Shad M. Sargand, Manseok Chang, Glenn A. Hazen

Customarily, peak particle velocity of surface wave vibrations has been the recommended criterion for the prediction of blast damage to structures. Currently blast spectrum and natural frequencies of a structure have been also recognized as important for predicting damage potential. While others have considered the importance of structural frequencies, they have not analyzed the structural response spectrum when establishing damage criteria.

Jan 1, 1992