Search Documents

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By Qian (Ken) Liu, Remi Proulx

A large scale blast damage project was carried out over the past two years at INCO Ltd Manitoba Division co-funded by the Canada/Manitoba Mineral Development Agreement. The experiment was conducted at the T-3 Mine in two mining stopes with an experimental drift developed in the hanging-wall for the installation of monitoring instrumentation. The objective was to observe and subsequently to reduce ore dilution by monitoring the performance of blasts, the hanging wall movement, as well as the cavity of the open stopes.

Jan 1, 1995

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By Zuhair Ibrahim, Dan Tillema, Ali Reza

This paper details the investigation of a fatal explosion that occurred on April 8, 2011 at a magazine used to store fireworks in Waikele, HI. The fireworks had been confiscated by the Bureau of Immigrations and Customs Enforcement after they were informed that a container shipped to the United States contained illegal fireworks. Four groups of cardboard cartons that were marked as 1.4G (consumer fireworks) were determined to be consistent with the more explosive 1.3G type, commercial display fireworks. The subcontractor retained to destroy these fireworks stored the shipment in the subject magazine and was in the process of disassembling them on the day the explosion occurred.

Jan 1, 2014

Vibrations are of concern not only for the safety of surface structures but also for the stability of underground openings. A number of parameters affect the intensity of vibration in underground openings due to blasting in adjacent opencast mine viz. total explosive weight detonated in a round, maximum explosive weight per delay, propagating media, depth of cover, RMR of the roof rock, age of the underground openings etc. Although a few researchers have tried to study the impact of parameters stated above, the impact of initiation sequences on generation of vibration in underground openings due to opencast blasting has yet remained untouched. A study was planned to evaluate the impact of initiation sequences on the magnitude of vibration in underground openings due to blasting in opencast mine. Nine production blasts with top and bottom initiations were performed at Samleshwari opencast project in India and eighteen vibration data were monitored in the roof of Hingir Rampur underground colliery in both the initiation sequences. The result indicated that the vibration produced in the underground openings from bottom initiation was lower than that of top initiation.

Jan 1, 2003

By Robert Martin, Brian W. Stump, David P. Anderson, W Scott Philips

Since 1994, various mines in the US have cooperated with research scientists at the Los Alamos and Lawrence Livermore National Laboratories to address issues related to verification of the Comprehensive Test Ban Treaty (CTBT). The .CTBT requires that no country may conduct any nuclear explosion in the future. While the CTBT is a significant step toward reducing the global nuclear danger, verifying compliance with the treaty requires that the monitoring system be able to detect, locate and identify much larger numbers of smaller amplitude seismic events than had been required previously. Large mining blasts conducted world-wide will be of sufficient amplitude to trigger the monitoring system at the lower threshold. It is therefore imperative that research into the range various blasting practices employed, the relationship of yield to seismic magnitude, and identification of anomalous blasting results be performed. This paper will describe a suite of experiments funded by the Department of Energy and conducted by the Los Alamos and Lawrence Livermore National Laboratories in cooperation with the US mining industry. Observations of cast blasting, underground long wall generated coal bumps, stoping, and explosively induced collapse of room and pillar panels will be presented. Results of these dual use experiments which are of interest to the mining community will be discussed. These include 1) variation of amplitude of seismic energy at various azimuths from cast blasts, 2) identification of the extent of back failure following explosive removal of pillars, and 3) the use of single fired shots for calibration of the monitoring system. The wealth of information and discovery described in this paper is a direct result of mutual cooperation between the US Government and the US Mining Industry.

Jan 1, 1997

This paper will review some of the work conducted in the past at the Dynamic Effects Laboratory to examine the use of stress waves and fracture mechanics in understanding dynamic fracture and fragmentation in blasting applications. Along the way, we will use photoelasticity and high speed photography to better understand the mechanisms of fracture and fragmentation.

Jan 1, 2015

By Tony A. Rorke, Joe R. Brinkmann

The application of instrumentation to better understand and improve production blasting is one of the most fruitful areas of explosives and blasting research. The majority of instrumented studies of production blasting have relied on the extrapolation of far field measurements to postulate blast performance in regions of interest closer to the charge where rock breaking takes place. However, the nonlinear and dissipative nature of the quantities being measured raises serious questions as to the accuracy and validity of such extrapolations.

Jan 1, 1991

By Stephen Chung, Graham Mustoe, Joe Haid

In an open cast coal mining operation, a 305 m (1000 ft) long by 49 m (160 ft) thick overburden cast blast can produce more than a million cubic yards of broken muck that needs to be removed before the coal recovery process can start. In the Powder River Basin of Wyoming, it is common to see 30 to 40 percent of the overburden cast to a spoil that does not require rehandling with heavy equipment. Therefore, the higher the percent cast, the better the cast blast is rated. However, depending on the shape of the muck profile, there is often 20 to 30 percent of the muck standing in front of the high-wall. This portion of muck would require a number of dozers to push down to the dragline pad level. From the mine operator point of view, it is believed that for a given muck profile, there should be an efficient dozer pushing method such that a dragline pad can be developed in the shortest time. As a tool for analyzing this dynamic problem, a 2-D discrete element model, i-PushTM, has been developed to simulate a dozer pushing operation. This mechanistic model takes into account the dozer blade geometry, the dozer operating procedure (e.g. cut-depth, blade fill distance, forward and reverse speeds at specific slope angles), material density and cohesion. To demonstrate how i-PushTM can be used to help determine the most productive push routine, this paper presents three dozer push methods to compare the effectiveness of pushing at 3:1, 4:1 and 5:1 push angles.

Jan 1, 2006

By Jim Hall, Denis Rickman, Jon Windham, John Ehrgott, Stephen Akers, Byron Armstrong

With the growing concerns about terrorism world-wide, numerous agencies conduct experiments to investigate the effects of terrorist vehicle bombs. In many cases, the vehicle bomb of interest utilizes some form of ammonium nitrate/fuel oil (ANFO) as the explosive source. Due to the high cost of fullscale testing, it is advantageous to conduct at least some vehicle bomb experiments at reduced scale. Extensive testing has shown that ANFO is a non-ideal explosive, and its explosive output does not scale reliably at explosive masses below approximately 400 lb (182 kg). Most scale-model testing requires explosive masses 1 to 5 orders of magnitude smaller. Thus, scale-model testing is typically conducted with “ideal” explosives, such as composition C-4, which perform in a scalable manner at virtually any charge mass. The utilization of an ideal explosive to model ANFO requires the existence of an accurate means of equating the performance of the two explosives. The airblast equivalence of C-4 and ANFO has been well established. However, the cratering equivalence of these explosives is not thoroughly quantified. This is especially true for the case of an above-ground detonation, which is precisely the scenario of interest in vehicle bomb studies. A study has been conducted to better define the cratering equivalence of C-4 and ANFO for above-ground detonations. This paper presents a discussion of results from this research.

Jan 1, 2008

"Recently, an effort was made to calibrate the Riedel-Hiermaier-Thoma (RHT) material model to reproducethe behavior of granite under impact and explosive loading conditions. The study concluded that the materialmodel captured the phenomenon of compressional damage in granite due to such loading conditionsfairly well. The present work uses hydrodynamic modeling with the calibrated RHT model to estimate thefines generated around a blasthole. This can improve the calibration of different size-distribution empiricalmodels and enhance the prediction of fines."

Jan 1, 2012

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Bruce Vandenberg, Andy Battfay, Don Lake, Steve Conway, Jeff Yorsz

"High-speed motion pictures are an invaluable resource for blasting analysis. Whether processed by the human eye or a computer, this imagery can provide important insight into a blast and its effects.While certainly popular, traditional high-speed film cameras hamper this process. Instant feedback is not available since film requires developing and, relevant in the case of automated analysis, film isnot immediately compatible with a computer. With these facts in mind, a new high-speed video camera system, the SVCSOO, has been developed. The SVC500 combines the capabilities of a high-speed film camera, the convenience of a solid-state digital video camcorder, and the computing power of a ‘486 PC to provide a complete, standalone platform for high-speed image acquisition and analysis. This paper will describe the design, features, and use of the SVCSOO andcompare these with the analogous aspects of film cameras."

Jan 1, 1994

By Charles R. Barnhart

The Nitrogen Dioxide Cloud: After one year of testing it can be stated that we do know and understand a great deal about why the nitrogen dioxide formation is exacerbated in cast blasting. Picture 1 is an example of how concentrated the NOx can be from a cast blast. It has long been felt that 300 or more milliseconds of timing needs to be put between each row of detonations to allow the rock a maximum time of flight so the cast percentage is high. Our experiments have found that higher cast percentages can make with timing between 150 to 200 milliseconds between rows. Picture 2 show a definite improvement in nitrogen dioxide concentration and most of that was the result of shooting a previously shot end of the cast pattern that had not been dug, thus no confinement of the powder columns.

Jan 1, 2004

By Roger Keller, Jason Ryan

A number of studies have evaluated excavation methods for the construction of subsurface facilities for a potential deep geologic repository for the disposal of nuclear waste at Yucca Mountain, NV. Many of these studies suggest that where TBM (tunnel boring machine) methods are not applicable and alternative mechanical excavation methods can not efficiently excavate harder rock drill and blast methods may be the most efficient means of excavation. However, a number of concerns regarding drill and blast applications have been raised in these evaluations, most notably the affects of blasting on the surrounding perimeter, as isolation of the waste by the natural barrier of the surrounding rock is a key element in the concept of a deep geologic repository.

Jan 1, 2001

By Türker Hüdaverdi, Özge Akyildiz

"Efficiency of blast operations depends on fragmentation, overbreak, muckpile profile anddisplacement, vibration, airblast, flyrock and damage to wall or slope stability. To provide all these conditions at the optimal level, determination of rock mass properties (in-situ block size, joint spacing and orientation) is the very first step during design stage of rock blasting. Image analysis software is used not only to determine the fragmentation level of muckpile but also to characterize the bench face. In this study, an image analysis software was used to determine apparent block size of bench face and to measure blast fragmentation of muckpile. The source of errors and the vital points to be taken into consideration were explained for bench face characterization andfragmentation measurement. Since it provides much better results than previous techniques and it is not intrusive to production process, image analysis technique is considered as one of the most efficient and preferred way for fragmentation analysis. Besides these advantages, there are some weak points of image analysis software. Lighting is one of the most important factors for photographs captured for in-situ block size analysis and fragmentation analysis. Lighting determines shadow formation. In an ideal image, particles are clearly delineated by soft shadows. If shadows are too strong (dark), analysis suffers. Appropriate scale should be replaced onto blast muckpile during site measurements. The location of the scale in image affects the results of analysis. Also, the densityand orientation of discontinuities should be considered during application of image analysis technique to characterize bench faces. In this study, image analysis software was applied in thesandstone, limestone quarries of Istanbul region and an open pit boron mine. All image analysis, evaluations and results were made based on the site measurements."

Jan 1, 2017

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Randall M. Wheeler

The purpose of this workshop is to illustrate how computer software can be used to evaluate blast design timing and simulate probable vibration characteristics. The workshop will be presented in two parts. Part I will cover the COMPU-BLAST Blast Design and Timing Analysis Program. Part II will focus on the ALPHA-BUST Vibration Analysis and Waveform Simulation Program. The information presented in the workshop will show how these two programs can be used together to help plan blast designs and aid in the control of vibration effects.

Jan 1, 1991

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

By William E. Hill

The blasting program at the Valdez Creek Placer Mine must deal with challenging situations throughout the year. During the short summer, extreme water conditions must be confronted, while the winter months present problems of a different nature, where the overburden freezes to a depth of up to 18 feet. These obstacles require techniques borrowed from hardrock blasting combined with creative experimentation to overcome.

Jan 1, 1994