Search Documents

By Zhang Qi

For the most part, the flying piece is serious endangerment in the demolition blasting. To prevent the endangerment, a large number of materials are needed as the protection. Therefore, the determination and design way of the flying distance of piece in demolition blasting have been concerned extensively. Previously, the experienced or half experienced formula was adopted to calculate the distance of the flying pieces. The calculating values of the distances of flying pieces are not identical with the practice results. The problems concerning the design way of flying distance of pieces are researched in the paper.

Jan 1, 1994

By George P. Jr Schivley

Looking at the process of drilling rock from the standpoint of the power required, yields an equation that relates Force-on-the-Bit; Torque, to rotate the bit; and bit Angular Speed to the Penetration Rate of the bit; the Area of the hole being drilled and the Specific Fracture Energy of the rock. Specific Fracture Energy and the Compressive Strength of the rock are related.

Jan 1, 1994

By Ruilin Yang

This paper presents a fragmentation model for large production blasts. The model uses peak particle velocity (PPV) induced from the blast as a controlling parameter to predict the fragmentation size distribution. The PPV can be related to shock pressure or strain under a given rock condition. The fragmentation size is calculated at three-dimensional grid points within the blast volume. The grid size defines the calculation resolution of the model. The fragment size distribution is assumed to be in the same form as the crack distribution within a cube (of the size equals to the grid size) surrounding a grid point. The crack distribution in rock from impact is based on the finding from previous researchers (Seaman et al., 1976). The fines and oversized blocks are calculated explicitly. The summation of the size distribution at all calculation grid points over a specified volume of the blast yields an overall size distribution for the volume.

Jan 1, 2015

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By Karl E. Burger

Recently an experiment was completed at the Golden Sunlight Mine, a property owned by Placer Dome Inc. of Vancouver, British Columbia, to measure the Body Waves entering their highwall created by blasting. The purpose of the study was to assess the damaging effects of blasting on the highwall, in order to further slope stability. Stress and Strain experienced in the earth that is created as a result of blasting can be determined by knowing several important pieces of information. These include the compressional and shear wave particle velocities initiated by blasting, the Body Wave travel velocities in both the shear and longitudinal direction, and the densities of the rock in question. A series of equations based on wave theory can then be used to determine the stress and strain affecting the highwalls. The Blasting Engineer can then use this information to design blasts that create peak particle velocities less than levels that maintain the integrity of the highwalls. This paper first discusses the experiment used to measure the Body Wave velocities. It then traces through the subsequent calculations necessary to generate the information needed by the Blasting Engineers, the Mining Engineers, the Geological Engineers, and the Geophysicists to design blasts and develop open pit plans to alleviate unstable highwall conditions.

Jan 1, 1989

By Fumihiko Sumiya, Yukio Kato, Yoshikazu Hirosaki

Secluential blasting is one of the most popular methods in blasting. tiowever, it is well known that an emulsion explosive can be dead-pressed by dynamic pressure generated by the previous detonation. It is difficult to gain the expected blasting performance due to tb.e malfunction of explosive caused by deadpressing and shock desensitization. Such malfunction of an explosive is undesirable for safety blasting operation. Voids in the emulsion explosives will considerably affect the performance of explosives such as sensitivity, detonation velocity (DV), pressure-resistance and so on. To clarify the detonability and the performance of precompressed emulsion explosives, the DV was measured. Three types of microballoon or micro bubble ; two types of glass microballoon(GMB), resin microballoon@MB) and chemical gas bubble ; were used as sensitizers for the sample emulsion expiosives. The underwater explosion test was carried out to load dynamic pressure into the sample explosives. The dynamic pressure was generated by the detonation of a donor explosive, and the DV of the sample explosives as acceptor was measured by ionized gap terminals. The dynamic pressure level and initiation interval for the donor and the acceptor were chosen as experimental factors. The detonability was carefully investigated at short initiation intervals taking into consideration the interaction between same delays caused by the deviation of the ignition time of the electric detonators. From these experiments, the following results were obtained ; A) The DV of precompressed emulsion explosives was low compared with that of uncompressed emulsion explosives in all pressure conditions. B) The decrease of DV in the sample explosives sensitized by GMB s was larger than that of DV in the sample explosives sensitized by RMBs or chemical gas bubbles. C) The recovery of the detonability occurred rapidly in the sample explosives sensitized by RMBs and chemical gas bubbles. However, a long period was needed for the recovery of detonability in the sample explosives sensitized by GME! s. It was concluded that the type of microballoon and micro bubble significantly influenced the detonability of precompressed emulsion explosives.

Jan 1, 2002

By Catherine Johnson, Kelly Williams

The ability to measure the overpressure of a shock wave is necessary for explosives research such as shockwave focusing and field testing of blast-resistant designs for buildings and vehicles. To record the peak overpressure of the nearly instantaneous pressure rise at the shock front, pressure transducers with a fast response rate and streamline pencil design are needed. Time spent setting up sensors coupled with the expense of high-frequency data acquisition systems, and the inconvenience of low impedance cables can make the process challenging. Additionally, only small inaccuracies in sensor position can drastically change the measurement recorded. Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount. This paper investigates the accuracy of this method by setting dual transducer pencil probesat0and180 degrees perpendicular to the central axis of a285-gram(0.63-pound)cylindrical charge to record pressure versus time for comparison to the high-speed video. The axis of the camera lens is aligned with the central axis of the charge with both pencil probes in view. The pencil probes have two pressuretransducersset100millimeters (3.9 inches)apart to measure the time of arrival and are used to validate the velocities calculated from the high-speed images. This method can be used to evaluate the shock wave propagation from more complex prismatic charges with different cross-sectional shapes where precise placement of cumbersome pencil transducers in the near field is almost impossible.

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By I. Petrovsky

Presence of the ground water, especially flowing water, causes limitations in the type of the explosives, which can be used for the blasting development in the open cats and quarries. This presents really big problem in Russia, because more than 70% of the blasting holes are wet and filled by flowing water. The waterproof explosives need to be used in these conditions, which increases the cost of the blasting development. So the search of the methods to remove the water from the blasting hole and to prevent direct contact of the explosive material with the water is important. It will give possibility to use nonwaterproof explosives (such as ANFO) and decrease the cost of the blasting development.

Jan 1, 2003

By Scott Scovira, Ruilin Yang

This paper presents a non-waveform blast vibration model for the near-fi eld. The model uses the concept of a dominant charge augmented by other contributing charges estimated using a scaled time window. The model accounts for the effect of broken ground created by earlier fi ring holes, amplitude attenuation, effects of signal broadening with travel distance from frequency attenuation, as well as asynchronous propagation of different wave types due to the wave velocity difference, the delay time effect, and non-linear superposition of near-fi eld vibration. The model uses an effective distance defi ned from the broken ground screening, and determines a dominant charge contributing to the PPV at a monitoring station. Then the model uses a time window for each individual charge to determine if it contributes to the PPV. The time window has a variable width to model the effects of the signal broadening with travel distance. For modeling the signal broadening, a generalized rock quality factor Qd is proposed. The time window includes a weighting function that diminishes the contribution for charges fi ring further from the dominant charge and this accounts for contribution arising from the timing difference between a contributing charge and the dominant charge. The model uses a non-linear charge weight superposition technique that scales the charge weights within the time window to the same distance of the dominant charge and superimposes the scaled charge weight. The case study demonstrates that the model provides useful predictions for near-fi eld blast vibrations.

Jan 1, 2008

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Håkan Schunnesson, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD)data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al.(2018) and Navarro et al.(2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave-in rock and cavity. From it, an application for the geotechnical rock condition of ore bodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting. The procedure has been applied in the geotechnical block model results obtained from Navarro et al.(2019)’s work in the Luossavaara-Kiirunavaara AB’s (LKAB) Malmberget underground iron ore mine, Sweden. Navarro et al.(2019)’s model was developed based on102 fan-holes from five ore bodies and extrapolated to the full-scale in20 drifts with 5600 fan-holes from two orebodies. A multi-step transformation of the MWD parameters was carried out in order to minimize external influences other than the rock mass. The study shows the calculations of the variogram and kriging estimation in the 3D domain for six ring-blasts, from one of the ore bodies studied in Navarro et al. (2019)’s work to assess the continuity of the rock classes along the six ring-blasts in a 3D mapping model. For that, intermediate rings between the measured ones from the MWD have been estimated. The probability distribution of values in the entire domain of rings with measured samples has been plotted together with the rock classes identified by the blasthole paths. The results show high accuracy in the matching between the kriging and the values given by the MWD data, allowing to visualize smooth trends of different rock classes along the ring. The representation of the 3D mapping model for the six ring-blast shows clear fractured and cave-in zones developed along the drift that correspond to zones with geotechnical problems found, as from internal reports.

By A. Andrades, E. Arias, Y. Pizarro, J. Alarcón

Division Ministro Hales - Codelco (DMH) is located at 2600 meters above sea level, 10 km north of the city of Calama, Antofagasta region, Chile. In operation since 2010, it corresponds to a porphyry copper deposit that is exploited by the open pit mining method. The ore is mainly composed of sulfides, which is concentrated by comminution processes such as crushing, SAG milling and ball milling to liberate the mineral particles, and then separated from the waste (concentrate) in flotation stages, including a concentrate regrinding stage. Reports from the DMH processing plant area have identified a decrease in fine copper recovery, with the first hypothesis being the high percentage of ultrafine particles (% <45µm) in the flotation feed. Due to the above, DMH & Orica decided to carry out activities to identify the controllable variables that can impact the generation of low size particles in ore and adjust them to reduce the percentage of fine material generation, with special focus on the Drilling and Blasting processes. Based on the data provided by DMH, we evaluated what could be integrated to make an analysis. The different attributes associated with the ore and their effect on copper recovery were evaluated. In parallel, at the mine, a fragmentation measurement campaign was carried out at the loading faces and granulometric analysis of the drill cuttings. Once the correlations between the attributes and copper recovery were identified, hypotheses were established and reviewed with the Drilling & Blasting, Geotechnical, Geology and Process Plant areas. With the validations of the hypotheses and the results of the in-mine (cutting) measurements, we proceeded to review the criteria for the classification of Blastable Geotechnical Units and their associated D&B designs. Using software and the Crush Zone Model (CZM) tool, which considers rock and rock mass parameters, scenarios for various D&B design proposals were simulated with the objective of reducing the generation of ultrafine particles from the blasting process. Next steps include trial blasting with the D&B design recommendations, which will require follow-up to the flotation process to identify the impact on the reduction of ultrafine material from blasting.

Jan 1, 2024

By Peter Moser, Mark Ganster, Radoslava Ivanova, Florian Bauer

Blasting accurately in underground drifts and creating a smooth contour requires proper drilling, knowledge about the apparent geology, a well designed blast pattern and ideally a smooth blasting product. These products are usually cartridged explosives with less energy and are charged in the contour holes in order to reduce the energy concentration and therefore the cracking into the surrounding rock. With the development of a new contour blasting system, a device can now be delivered to the industry that that avoids the additional storage of cartridged products when bulk explosives are used. The system consists of a foldable hose that is charged with bulk emulsion, in the same way as the rest of the blast, from the base to the collar of the hole. It centers automatically in the borehole and provides a decoupled charge. The paper describes the system in detail, gives background information on smooth blasting and presents the first successful field tests using the system in the drifts of an underground mine. It shows the advantages of blast results that produce more stable contours that reduce the amount, time and cost for support but also increase safety underground.

Jan 1, 2012

By Douglas Bartley, Kevin Hachmeister, Rich Barry

The use of explosive energy as a tool in mining and construction is the most effective way to move large amounts of rock that is otherwise unable to be efficiently excavated. Since the early days of explosive engineering utilizing black powder initiated by cap and fuse to the present day diversity of specialty products and technologies the goal has always been to "Break and Move" as much rock for the least expense possible. It has primarily been the competitive nature of our economy that has driven the advancement of technological innovations and practice. However, the concept of removing rock is not specific to the mining and construction industry. Since the dawn of creation, man has used rock as a medium to express his creativity in the form of sculpture. Even though the process of sculpture requires the removal of rock, the final work is defined by the rock that remains intact. This typically necessitates the extreme care of the sculptor to painstakingly chip away the rock allowing the image to emerge from the original mass of stone. The famous sculptor Michelangelo once said, "I saw an angel in the marble and carved until I set him free."

Jan 1, 2004

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.