Search Documents

By Piotr Mertuszka

Many years of research on more effective and safer explosives have led to the development of emulsion explosives. They are the second most commonly used group of explosives worldwide, primarily because they are good alternatives to ANFO or dynamites. Their key advantage in underground applications is the lower content of toxic fumes in the detonation products. Emulsions are also characterized by high detonation velocity, high water resistance, low critical diameter, and mechanical loading capacity. Several factors affect the behavior of emulsion explosives. These factors are related to both manufacturing and applied mining methods. The most important factors include the charge diameter, type of sensitizer, density, hydrostatic pressure, ambient and charge temperatures, as well as the time elapsed between the charging of the explosive into the blast hole and its detonation. The selection of the type of explosive is based on the analysis of a number of parameters, including the density, critical diameter, volume of the post-blast fumes, detonation pressure, velocity of detonation, and sensitivity to external energy sources. In most cases, the conditions under which explosives are used differ significantly from those defined in standards. Such conditions cover, among others, the temperature of the rock mass and surroundings, humidity, rock strength parameters and the diameter of the blast holes. Consequently, the parameters of the explosives provided by the manufacturers may not correlate with those specified in-situ. Thus, within the framework of this study, the effects of the selected technological parameters on the detonation velocity of bulk emulsion explosives are presented. The analysis focused primarily on the factors directly influenced by the mine blasting services. The detonation velocity measured using the continuous wire resistance technique was used as the evaluation criterion. For this purpose, several underground in-situ tests were conducted, including the impact of the blast hole diameter, density, initiation method, sleeping time, and temperature on the detonation velocity. The results of in-situ tests have shown that the detonation velocity of bulk emulsion explosives depends strongly on the above factors, which may directly affect the effectiveness of blasting operations.

Jan 26, 2026

By Thomas E. Ricketts

Occidental Oil Shale, Inc. constructed two commercial-sized modified in situ (MIS) retorts, Retorts 7 and 8, at its Logan Wash Oil Shale Mine in February and April 1981, respectively. One of the primary objectives of this two-retort program was to examine large-scale blasting reproducibility for commercial-sized retorts. The blast design used 545 blastholes and 550,000 pounds of explosive in ANFO equivalent per retort. Each retort was blasted using millisecond delay blasting caps tied into a single round. The blasts resulted in rubble beds very close to one another and to predicted results obtained using newly developed limited void blasting technology. The heights of the remaining void rooms over the beds after blasting were within 0.3 feet of one another. This excellent reproducibility is brought into true perspective when compared to the scale of the rubble beds which were 230 feet high with volumes of over six million cubic feet each.

Jan 1, 1984

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Yong Pan, Purushotham Tukkaraja

In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

Feb 1, 2020

By Tapan Goswami, Stephen Jeric, Geoff Brent

Highwall failures in large deep open cut mines have very significant safety and commercial implications. There are many factors influencing the stability of highwalls. The major influence is the interaction of the local geology with the shape of the pit wall. This factor is in the realm of the geotechnical engineer and is beyond the control of the blasting engineer. However, a secondary influence is the blastinduced damage to the wall. In most open cut metal mines the blasting strategy to control this damage involves the use of separate production and trim blasts bounded by presplits at the final wall.

Jan 1, 2011

By Svatopluk Zeman, Zbynek Akstein, Jiri Pachman, Ahmed Elbeih, Marcela Jungova

BCHMX (cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole or Bicyclo-HMX) was studied as an energetic component of three different plastic explosives based on three matrices: C4 matrix, semtex10 matrix and silicone matrix. The original plastic explosives, Composition C4 - based on RDX (1,3,5-trinitro-1,3,5-triazinane), Semtex 10 explosive based on PETN (pentaerythritoltetranitrate) and plastic RDX-silicone, were included for comparison. Sensitivity and performance parameters were studied.

Jan 1, 2011

By Ethan Steward, Kyle Perry

To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals.

Feb 1, 2020

By John W. Brown

During the summer of 1994 the mining industry experienced numerous accidents involving blasting related incidents. The Tri-State Chapter of Explosives Engineers planned a meeting to discuss three of these accidents.

Jan 1, 1995

By M. S. Dotto

The knowledge of the explosive/ rock mass interaction process is important in predicting blast performance. It includes understanding rock properties, energy usage, and attenuation in the rock mass. The paper proposes a method to quantify blast-induced rock mass damage from the field measurements and apply it to modeling blast fragmentation.

Feb 1, 2020

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed.

Feb 1, 2020

By Andre Pienaar, Larry Wilson

Destruction of waste emulsion by blasting has been proven to be risky and disastrous incidents have been seen when using this practice. Our R&D department in conjunction with Lake International has developed an emulsion breaker system where underground waste can be destroyed safely. The methodology and logistics around the system will be demonstrated during the presentation. This process offers a safe alternative for the removal of sensitized and un-sensitized waste products from these mining environments.

Jan 1, 2010

By Milos J. Bila

I would like to discuss today several safety topics that we at Nobel feel are going to be particularly critical to all of us who are involved in the manufacturing, transportation, storage and use of commercial explosives during the '90s. My purpose is to identify these topics in order to allow those in the commercial explosives community to better understand the potential difficulties we face.

Jan 1, 1992

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By D. S. Scovira, T. Gustavsson

Exiting WW2 (mid-1940s), the potential of nitrates (ammonium nitrate, calcium nitrate, sodium nitrate) and hydrogen peroxide for application as a commercial explosives for mining, construction, and other industrial purposes both became known. The technology stream advanced the development and uptake of nitrate based explosives to the point that they are the current global standard for blasting. Today, environmental issues are shaping the strategic agenda across various industries. Most global mineral resource, construction houses, and explosive manufacturers have publicly announced ESG carbon reduction commitments in support of COP26 Net Zero 2050. The mid-2010s saw a renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the early 2020s provided additional impetus to investigate hydrogen peroxide based explosives for industrial use. Hypex Bio has recently pioneered the formulation, manufacture, and end-use delivery of a Hydrogen Peroxide Emulsion (HPE) on an industrial scale. The HPE is composed primarily of hydrogen peroxide (H2O2) plus a lesser amount of fuel and emulsifier phase. The base HPE is produced in a low energy intensity modular plant using industry proven mixing techniques. The base HPE is a white, highly viscous emulsion that is similar in consistency to base nitrate emulsions. To enable end blasting use, a mobile charging unit gases the base HPE to a detonable density. The HPE is compatible with current priming and initiation systems. Hydrogen peroxide explosives offer a significant reduction in total carbon emission as compared to nitrate based explosives. The production of ammonium nitrate (AN) emulsion is energy-intensive and not carbon neutral. Based on the EU Average and for the oxidizer phase only, 1 kg [2.2 lb] of AN emulsion emits 2.3 kg [5.1 lb] of CO2 as compared to the production of hydrogen peroxide emulsion that results in 0.23 kg [0.5 lb] of CO2. This is a difference of 90%. HPE contains no nitrates and does not generate post blast nitrous oxides (NOx). HPE generates no aqueous nitrate or ammonia pollution and is a solution to meeting increasingly regulated mine site water discharge limits. Hypex Bio recently conducted a successful underground HPE evaluation with a major mining company in Sweden. HPE blast designs were the same as those done with nitrate based emulsions. Rock breakage, advance, muck displacement, and excavator performance were equivalent. Ventilation and re-entry times were reduced. The mining company has expressed further interest in assessing HPE and is demonstrating industrial leadership by exploring this transformative explosive technology

Jan 1, 2024

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By William Hissem

The topics in the title line of this article are desirable and applicable to entire industries that exist outside the realm of the ISEE’s readership. But the issues I will discuss herein are specific to those who drill, blast, and excavate rock as part of their business. Civil and site construction projects, mines, and quarries specifically comprise the group who will benefit from this discussion.

Jan 1, 2014

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025