Search Documents

By Eduardo Lozano, Vilem Petr

This study demonstrates the ability of high-order, shock-capturing methods to simulate detonation wave propagation in right circular cylinders of non-ideal explosives. 2-D axisymmetric, reactive Euler equations were solved for the detonation of the highly non-ideal explosive ammonium nitrate-fuel oil (ANFO) using a simple pressure-dependent rate law and perfect gas equation of state. The fractional step method was applied to the convection and reaction operators using a 2nd-order Strang splitting. The flow solver consisted of a finite difference scheme where the flux is reconstructed by a modified fifth-order weighted essentially non-oscillatory (WENO5-Z) with local characteristic decomposition and local Lax-Friedrichs (LLF) flux splitting. Time integration was performed by a third order total variation diminishing (TVD) Runge-Kutta time discretization method, also known as the strong stability preserving (SSP) method

Jan 1, 2019

By Nick Lewis, Paulo Pereira

The Vulcan McCook quarry has been in operation for about 100 years. It is located about 17 miles from downtown Chicago and is surrounded by both industrial and private structures. Recent issues have forced the quarry to blast very close to structures and this will be necessary years into the future. This paper discusses the implementation of electronic detonators to McCook. It also discusses the advantages and savings that the Program has achieved

Jan 1, 2003

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Cristian Rodriguez, Tom BoBo, Maria Rocha, John Kemeny

Blast fragmentation depends on many factors. First of all, it depends on the specific blast design, which includes the amount and type of explosive, the blasting pattern, the timing and sequencing, and other parameters. Secondly, it depends on the properties of the rock mass, including the uniaxial compressive strength (UCS), the rock mass elastic modulus (E), the rock discontinuity characteristics (as reflected in the GSI or RMR), and the rock density. Several fragmentation models have been proposed to predict blast fragmentation based on the blast design and the properties of the rock. These models include the Kuz-Ram model and variations of this model, as well as recent models by Kim and Kemeny (2011) and others. Fragmentation models are validated and calibrated by comparing the predicted fragmentation with actual post-blast fragmentation from image processing monitoring systems.

Jan 1, 2014

By C. Pelley, S. Kelebek, P. D. Katsabanish, M. Pollanen

A series of small scale tests have been conducted to evaluate the effect of blasting on the grinding resistance of rocks. The samples consisted of homogeneous blocks of granodiorite and limestone while blasting was performed using single and multi hole configurations. Grinding resistance was evaluated using relative ball mill tests, rod mill tests and the SAG Performance Index test (SPI) developed by Minnovex. It was shown that the grinding resistance was affected by blasting. However the effect depended on the final product size. In the case of the coarse grained granodiorite, a negligible effect was observed for grinding below the natural grain size of the rock, while the fine grained limestone exhibited more significant changes, in the range of 13-16%. Grinding of granodiorite in the coarse size range indicated a general reduction of its work indices, as evidenced by the results obtained from the ball mill, the rod mill and the SPI tests.

Jan 1, 2004

By Dale S. Preece

The computer program. DMC Qistinct Motion &de), which w&s developed for simulating the rock motion associated with blasting, has been used to study the intluence of row delay timing On rock mOtiOn. The munerical simulations correspond with field observations in that vmy short delays (< 5Oms) and vety long delays(> 3oOms) produce a lower percent-cast thao a medium delay (100 to ZOO ms). The DMC predicted relatio&lp between row delay timing and percent-cast is more complex than expected with a dip in the auve where the optimum timing might be expected. More study is required to gain a full undasranding of this phenomenoo.

Jan 1, 1994

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Gary B. Hemphill

Estimators will agree that estimating for excavation is the most difficult costing task. Equipment costs and production rates are the toughest to determine. The following illustration is a method that can be used for this determination.

Jan 1, 1976

By Alan Jorgansen, Dave Hummer, Scott Scovira

Kennecott Energy's Colowyo Coal Mine is the largest open pit coal mine in Colorado and produces 5.5 MM tons per year. Colowyo uses the terrace mining method to recover up to seven seams of rolling coal ranging in thickness from 5 to 20 feet. Draglines are used to strip overburden ranging from 60 to 120 feet thick off two coal seams. These two seams are characterized by soft and fold fractured coal and in past practice cast blasting caused excessive coal damage. As a result, to ensure minimal coal damage and high coal recoveries, the overburden was excavated in two passes. The first pass removed the upper overburden to within 10 to 20 feet of the coal seam. The second pass removed the remaining overburden above the coal. Two-pass mining was effective in controlling coal damage, but also carried significant additional costs.

Jan 1, 2003

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By Mike Cammack

Western South Dakota is predominately an agricultural area, with exception of the mining and timber industries in the Black Hills region. With precipitation rates averaging below fifteen inches per year, water is a precious commodity to the livestock industry. There is a constant demand for the construction of earthen water storage facilities (dugouts) to catch snow and rain runoff, or developing natural springs.

Jan 1, 1993

By Walter Voglauer, Elisabeth Zechmeister

Description of Project: The four photos show a chimney blasting operation in Vienna’s district of Floridsdorf on May 4 2011. The blasting was done with two types of charges. An internal charge provided a force of blast which resulted in 135 single electrical blasting caps initiated detonations on the basic ensured the straight collapse of the chimney. The preparation work was done by reserve force military engineers. The series of photos were shot by Elisabeth Zechmeister. She works in the Austrian DOD but not as a professional photographer; much more she did all activities in her spare time.

Jan 1, 2013

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Robert Boehnke, Bernd Mueller

Despite enormous efforts over the last decades there are still many unanswered questions with respect to calculation and modeling of the blast process using appropriate physical laws. Most calculations of explosive charges of a blast design are based on experience, empirical observations or blasting theories with serious shortcomings. This paper presents a new theory for the design and calculation of a rock blast that is based on the momentum. It offers a clear-cut method for the calculation of blast processes. The theoretical results will be compared with on-site measurements by means of a newly developed strain sensor and further measuring equipment. The momentum theory helps better to explain physically the processes of a blast. On the basis of long-term statistical investigations a momentum balance can be carried out with the volume-based blasting momentum and the measurable momentum associated with the muckpile and the remaining rock mass. This type of consideration requires a complex procedure which includes the blastability of the rock masses. Realis tic strain measurements open a new interpretation possibility and judgment criteria for the most probable building damage, the dynamic impact on general types of buildings and also for the blast process itself. The blast-induced stress and the momentum generated could be back-calculated using a geophone profile and the strain sensor. The strain owing to a dynamic impact can be influenced by the changing of the drill-, blast- and shotfiring technique like the until now measured vibration velocity. In this way it is possible today to make a complex preparation, calculation and evaluation of blasts. The new techniques of measuring in connection with the momentum theory bring about an increase of the safety and a clearcut method of improving the blast processes. This procedure offers new possibilities for the precise calculation, simulation and modelling of blasts and resulting vibrations and leads to an increase of the safety as well as economic adaptation of the drill-, blast- and shotfiring techniques to a pre-determined blasting result.

Jan 1, 2003

By G. R. Adhikari

Step 4: Selection of explosives and initiation system Various types of explosives are manufactured in India and a wide choice is available among them that include nitroglycerin based explosives, slurries, emulsions, ANFO (ammonium nitrate mixed with fuel oil) and heavy ANFO. The choice is also available between cartridged and bulk loading systems. In Indian mines, much importance is unduly given to the cost of explosives alone which is not conducive to optimization of blast design parameters. The concept of energy per meter of blasthole and the way in which the total explosive energy is partitioned between shock and heave is not considered in the prevailing practices. Besides, very little efforts are made to objectively evaluate the performance of explosives for a given site condition. Tailoring explosives is limited to changing the density of the bulk explosives. Cartridged explosives are still being extensively used in large operations where bulk explosives should be the preferred choice.

Jan 1, 2002

By Jeff Friedman

This paper addresses certain problems to be encountered when a blasting contractor agrees to provide indemnification. Nearly 100% of all blasting work is performed pursuant to a contractual agreement. Whether the explosives engineering firm works directly for the property owner, or for a general contractor by way of subcontract, indemnification agreements are generally required to protect owners, operators, general contractors, and other interested parties in the event there is subsequent litigation. These contractual requirements are typically referred to as indemnification and “additional insured” agreements. We will address the ramifications of contractual indemnification as well as “additional insured” agreements in this presentation. Some of the aspects of this paper will include:

Jan 1, 2004

By Dale Preece, Stephen Chung, Richard Jensen

DMCBLAST_3D is a three-dimensional extension of the proven two-dimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2001

By Pharis E. Williams

The ability of voids, microballoons, and even solids to sensitize explosives has been known and used for many years. This phenomenon has generally been studied and reported under the terminology of "hot spots" because of the increase in local pressure and temperature when a shock wave encounters such sensitizers. A method for treating this phenomenon in detonation theory or in a detonation model has been studied for almost the same length of time. Perhaps because of the complexity and non-linearity of the void, or microballoon collapse, several of these studies have used the expediency of including additional terms in the burn rate law to account for the influence of hot spots. The detonation model proposed here considers the sensitization due to discontinuities in the shock impedance to be a mechanical phenomenon to be accounted for in the mechanical equations governing the detonation and not in the burn rate law. While this is not a new contention, the method for handling this non-linear phenomenon within the proposed model is new. The model also includes a method which accounts for the manufacturing variables of emulsion matrix cell size, microballoon size and type, as well as energetic additives.

Jan 1, 1992

By H. Rossmanith

This contribution introduces the fundamental concepts of wave propagation and fracture mechanics which form the basis of electronic blasting, i.e. precise initiation timing using electronic detonators. The concept of Lagrange diagrams will be frequently used for the calculation of the delay time between blast-holes in a row and rows of blast-holes. The effect of burden and structural geology will be briefly touched. It is found that the advanced blasting technology based on the use of electronic detonators introduces a change of paradigm. It will be shown that knowledge in wave propagation and fracture mechanics is essential for the successful application of the new blasting technique in industry. In particular, the delay time, the wave speeds in the rock mass, the shape of the wave pulse and the acoustic impedance mismatch have become decisive parameters in advanced blasting. Utilizing the wave speed and wave shapes of detonations, large scale tests Utilizing the wave speed and wave shapes of detonations, large scale tests in various countries (Australia, Chile, etc.) have shown that optimal delay timing requires shorter delay times in conjunction with allowing for a wider drilling pattern and the use of a reduced amount of explosives, i.e. a lower powder factor. This seemingly contradictory arrangement is fully justified by using scientific principles in blasting, and converting blasting from an art to a scientific discipline.

Jan 1, 2003

By P Wapner, C Lo Edwards, S CO Schmidt, J N. Johnson, R Oliver

Shale oil recovery rates that can be achieved in underground in situ retorts can be strongly influenced by the shale breakage and fragment-size distribution achieved during rubblization. Since the fragmentation pattern in the retort is a direct result of the blast design used for rubblization, the characterizing blast parameters should be carefully selected. Explosives should be matched to the host material and blast geometries properly chosen so that the required fragmentation results are achieved at optimum costs. Special attention must be directed to selecting blast parameters that produce uniform bed permeability, suppression of fines, proper fragment size distribution, and minimal damage to the retort walls and ceiling. The influence of joints and natural fractures should also be known. In instances where the requisite blasting parameters are unknown, they should be determined from test blasts.

Jan 1, 1979