Search Documents

By Jerald E. Harris

"Often taken for granted, drill accuracy plays a major role in the relative success or failure of a blast.Expensive technological advances in equipment capabilities, drilling tools, communications, explosives, and timing can quickly be nullified by poor drilling."

Jan 1, 1999

By Theodore A. Christensen

Besides the moral responsibility for ensuring worker safety, today's blasting contractor has a major financial incentive for establishing an effective safety program: on-the-job accidents have a direct impact on a very sensitive cost area - Workers Compensation. Within specific parameters, a good safety program can reduce WC costs by lowering the Experience Modification Rate.

Jan 1, 1993

By Gungor Tuncer, Ali Kahriman, Umit Ozer, Abdul Karadogan, Mehmet Aksoy, Ertugrul Kaya, Deniz Adiguzel

This research was performed on the quarry that will be opened to produce aggregates and rock filling material at Catalagzi region at Zonguldak providence. Excavations will be done by drilling and blasting. However, there are some structures which can be adversely affected by blasting at the quarry. These structures are a methane exploration drill hole and a house at the distances of 340 m and 390 m, respectively. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting on these structures by risk analysis based on ground vibration measurements.

Jan 1, 2009

By Rachel Bernau

Water wells, aquifers, and pipelines rarely incur damage from nearby blast vibrations. Extensive ground vibrations may cause a drop in the water table thereby changing an aquifer’s structure or drying up a well. Studies on the reactions of aquifers and water wells have been performed in Montana, North Dakota, and the Appalachia Coal Region. All of these studies reported that vibrations did not change the properties of the monitored aquifers and water wells. Rather, evidence suggests that any incurred damage was caused by block motion and downsloping.

Jan 1, 2001

By Paul Downing

A major component of an effective blasting company safety program is the self-audit. A self-audit can help reveal hazardous conditions that should be corrected and training needs that should be addressed before accidents occur, insurance claims are filed, and/or fines are levied. Such audits, when they lead to appropriate corrective action, can provide significant economic benefits for employers by reducing the costs associated with insurance claims, accidents, and injuries.

Jan 1, 2001

By Randy Wheeler

One of the more difficult topics to address concerns the effects of vibration on historic structures. Not only blast induced vibration, but also vibration from other transient and semi-continuous sources like, traffic, human activity, and environment forces. A common question might be, “What level of blast-re l a ted PPV is considered safe?” A review of some of the papers available from the ISEE Explosives Reference Database on CD ROM shows that 0.50 inch per second was often used. It was not clear on what basis this value was selected except that it represents the low frequency limit for plaster developed by the United States Bureau of Mines in RI 8507. In another case, a limit of 0.20 inch per second was mentioned, apparently simply because it was ten times less than 2.00 inches per second.

Jan 1, 2004

By S. K. Chan, C. Badeen, S. Goldthorp, H. Feng, I. Alilovic, R. Turcotte

Over the last few decades, water-based explosives and their precursors, despite their apparent insensitivity, have been involved in a number of accidents around the world. A large proportion of these accidents occurred when these emulsions were pumped either for their manufacture, transport, or handling. In Canada, this has led to the development of “Guidelines for the Pumping of Water-Based Explosive”, which state that “using pumping pressures well below the laboratory measured minimum burning pressure (MBP) of the corresponding emulsions or watergels is a good safety practice”. However, in the above document, there is no description on how the MBP should be measured. In the last few years, a research program at the Canadian Explosives Research Laboratory (CERL) in collaboration with Orica has been focused on the development of a validated measurement protocol for realistic MBP measurements.

Jan 1, 2014

By John N. Jr Edl

Geokinetics, Inc. has pioneered an in-situ oil shale retorting production process that provides the requisite void space for producing a permeable rubble bed, within the retort zone, by using the explosive energy from vertical blastholes to lift the overburden. By installing suitable instrumentation on the surface of the overburden over an appropriate blasting pattern, it is possible to obtain estimates of the average radius of gas penetration around the blasthole and the average volume, per unit length of blasthole, that is actually occupied by the explosively produced gases (which includes both the volume of the cracks that are penetrated by the gas pressure and the deformed blasthole volume). It is expected that these estimates can be used to examine, and quantify, the effects of such blast design parameters as the type of explosive, the blasthole diameter, the geometry of the explosive charge (length to diameter ratio), and the relative timing of sets of charges.

Jan 1, 1983

By Ralph Dawson

The following additions to SLP-4 “ALWAYS AND NEVERS” have been approved by the Board of Governors since the last printing 6/97 and will be included in the next printing soon. They are also included in the Second Printing of the 17th Edition of the ISEE Blasters Handbook. Review them and apply those which might be applicable into your blasting program now.

Jan 1, 2001

By Syed M. Tariq, Paul N. Worsey

Presplitting is a now a universally accepted perimeter control technique in rock excavation. The success of presplitting and the smoothness and integrity of the resulting perimeter is largely dependent on the nature of joints in any given formation. Many facets of jointing have been previously investigated. The results of the effects of joints frequency and spatial positioning were presented by the authors at the ISEE annual meeting last year. This paper includes the results of further research into the mechanism of presplit blasting being carried out at the Rock Mechanics and Explosives Research Center of the University of Missouri- Rolla.

Jan 1, 1996

By Wang Hong Qu

This paper observes the shape of throw explosion crater its ejecta locus of internal medium and the process of distance along with slope's angle developing. It was discovered that initial velocity is inversely proportional to slope's angle. The velocity of surface distribution at the lower half crater of explosion is larger than at upper one. It carries the relevant calculated formula and physical process of explosion crater forming under the inclined boundary conditions, and some important law. It proved that the gravity influence is very distinct for the blast action in the little resistance line.

Jan 1, 1991

By Robert L. Martin, Brian W. Stump, David P. Anderson, David Gross

In an attempt to better understand the impact that large mining shots will have on verifying compliance with the international, worldwide, Comprehensive Test Ban Treaty (CTBT, no nuclear explosion tests), a series of seismic and videographic experiments has been conducted during the past two years at the Black Thunder Coal Mine. Personnel from the mine and Los Alamos National Laboratory have cooperated closely to design and perform experiments to produce results with mutual benefit to both organizations. This paper will summarize our activities, highlighting the unique results of each.

Jan 1, 1997

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Rob Famlield, Gavin Yuill, William Birch

The Blasting Research Group at the University of Leeds, in the United Kingdom, continues to be highly active in the area of the environmental impact of blasting. In recent years a major part of this research has been concerned with the use of linear superposition. This technique relies upon the assumption that all the holes in a blast produce identical vibration signals. Previous work at the University has shown that this assumption is not sufficiently robust to be generally applicable. This is due to a number of factors of which the key variable appears to be dynamic confinement

Jan 1, 2002

By Paul Worsey, Delbert Da, Eric Achelpohl

The University of Missouri-Rolla is currently researching the concept of using glass microspheres in explosives as taggants as part of a 3-year technical project funded by the Bureau of Alcohol, Tobacco, and Firearms. These taggants are intended to provide two functions, first explosive detection and second post explosive event identification. The key priority is being able to detect explosives used in terrorist acts prior to detonation. The research on the use of microspheres includes the development of indicator taggants for the purpose of revealing the presence of hidden explosives, by either emitting radiation when bombarded with neutrons or emitting selective vapors, such as DMNB which may be readily “sniffed”. Of secondary importance, after an illegal explosion, the tags serve to identify the lot number, etc of the explosive. This information is to aid in the tracking, arrest, conviction and imprisonment of the perpetrators.

Jan 1, 2001

By D T. Froedge

At the 1990 Symposium of the Society of Explosives Engineering, D.T. Froedge, President of GeoSonics Inc., presented a paper entitled "Differential Topographic Vibration Isomapping", which detailed the capabilities of GeoSonics' new Iso-Seismic Service. In this paper Mr. Froedge described how one hundred or &ore free-standing miniature seismographs called Micro-Seis Units, randomly positioned around a blast, could accurately reveal the effects of sub-strata geology on surface ground vibrations. The paper went on to note the "regression analysis of scaled distance versus recorded particle velocity" as being an inadequate predictor of peak particle velocity. This is due to the fact that the calculated "regression analysis" formula for any site is predicted on the wars; case assumption because of a homogeneous and symmetrical sub-strata geology, a condition that rarely, if ever, exists.

Jan 1, 1992

By Tristan Worsey, Nathan Rouse

The Florida legislature allocated funding for the Florida State Fire Marshal (FSFM) to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains

Jan 1, 2019

By Daniel Ko, Ian Bell, Shahram Tafazoli, Bahram Sameti, Aylin Azmin

Image-based remote sensing of rock fragmentation in mining and quarry applications essentially treats each rock in the image as a data object in order to determine the rock size distribution. An obvious challenge after rock delineation in a 2D image is the scale of the delineated objects. Conventionally, either objects of known size are placed in the scene or parallel laser pointer are used, both making some assumptions, to calculate scaling factors. These assumptions are applied to the whole scene rather than sensing individual rock attributes.

Jan 1, 2015

By Shuli Teng, Vladimir Sujansky, Matthew Rawls, Ivan Junarsa

In recent years significant advances have been made in chemical processing technology. In particular, process intensification using micro-technology has had some success in changing and improving chemical processes including mixing. Process Intensification is the miniaturization of unit operations and processes whereby a smaller compact piece of equipment takes the place of a larger one at the same given capacity or mass flow rate. This paper summarizes research into the application of the technology for manufacture of high internal phase water in oil ammonium nitrate emulsions (ANE’s) at low energy cost and with very low oil/fuel blend content. The emulsions can be used as precursors for preparation of explosives. The quality of the emulsion prepared was assessed through droplet and crystal analysis and compared with that of emulsions made by conventional large scale jet mixing technology.

Jan 1, 2014

By Larry Mirabelli, David Lilly

In 1777, the French naturalist, Georges Louis Leclerc, Compte de Buffon developed a statistical technique to estimate the width between two parallel lines by randomly throwing a needle at the two lines and counting the number of times the needle intersected one of the two lines. By knowing the length of the needle, the distance between the parallel lines could be estimated. This analysis was named the “Buffon’s Needle Problem”.

Jan 1, 2008