Search Documents

By Robert Hopler

The 1800’s were a time of tremendous advancements in science and experimentation, and earthquakes were a subject of great interest. The meetings of the British Association for the Advancement of Science in 1853 and 1854 are good examples of this. The proceedings of the Association for the 1854 meeting includes a table entitled “Catalogue of Recorded Earthquakes from 1784 to 1850” which takes up 326 pages, and lists available information on approximately 3000 earthquakes. The 1853 proceedings have a similar table for earthquakes recorded from 1606 B.C. to 1783. In the 1854 volume there is a “Report of the Committee on Earthquakes,” which provides us with a view of the general state of the science. Excerpts from that report follow:

Jan 1, 2006

By James Keenan

Mesabi Range blasting has evolved in over a century of mining. The obstacles including: hard and heavily jointed rock, bitter winters and frequent wet holes; combine to create a unique challenge for blasters. This paper documents current pattern designs, powder selection and loading practices for these seven mines that consumes as much as 130 million lbs of explosives each year. Blasting is characterized by wide burdens and spacings, large diameter holes (up to 16-inch) and bulk loading of augered and pumped emulsion/prill products.

Jan 1, 1996

By Stanley L. Lippincott

A number of Federal and State agencies require formal training for blasters. Federal agencies often specify the need for initial training involving all job responsibilities as well as periodic refresher training to assure adherence to current operating procedures. failure to provide and document such training can result in substantial penalties.

Jan 1, 1995

By Robert Hopler

RBH Note: At the time of this price list the handwriting was already on the wall regarding the ultimate breakup of the company under the Sherman Anti-Trust Act. The brand names Atlas and Hercules, noted on page 3 of this pricelist, would become the names of the new companies created from du Pont.

Jan 1, 2012

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Ruilin Yang

Based on large amounts of field data, this paper evaluates the validity of the above equations. During the evaluation, the different selections of the frequency in the equations were examined with field data. It is found that when they are used to estimate the vector sum values the above equations could result in large deviations from the values obtained directly from the field measurements or the waveform integration. The simple equations may be used to make rough estimations for single components of blast vibration provided that appropriate safety factors are taken into account. For single component vibration, the principal frequency (from ‘zero-crossing’) seems more effective to describe the blast vibration than the dominant frequency (fron FFT) for vibration peak value estimation using the simple equations.

Jan 1, 2012

By TA Louw, Dr CM Lownds

In an era where profits are constantly being eroded, mines are looking towards technology developments to assist them in solving mining problems and reducing mining costs. An emerging technology that could assist mines in becoming more cost effective is electronic detonators. Electronic detonators have been under development for several years. Over the past three years, the spotlight has fallen on commercial use of electronic detonators and the extent to which the promise of precise and programmable timing can assist mines with their environmental and productivity problems. This paper uses case studies to demonstrate both surface and underground applications where electronic detonators and blasting systems were used to solve typical mining problems such as vibration and fragmentation. Safety aspects such as hanging wall conditions and high wall stability also benefited from the use of electronic detonators. The paper also demonstrates how the use of accurate electronic detonators and blasting systems has resulted in improved/more even fragmentation with further downstream efficiencies. These efficiencies may include increased cast percentages, reduced oversized rocks, quicker cleaning times and increased production rates.

Jan 1, 2004

By Trevor Garbutt, Peter Bellairs, Jason Sander, Glenn Shaw

The Yarrie Iron Ore mine is located in the Pilbara region of Western Australia some 200km eastsoutheast of Port Hedland, the closest large regional centre. The mine is owned by BHPIO who has contracted a large Australian mining contractor Roche Bros to be responsible for the total mining, crushing and trainloading functions. This paper describes a drill and blast optimisation program, resulting from the introduction of a new emulsion matrix called Titan@ Red used to manufacture both HANFO and pumped emulsion ANFO blends.

Jan 1, 1999

By Alastair Torrance, Braden T. Lusk, MinGi Seo, Gary Cavanough

Velocity of Detonation (VOD) is the most commonly used method to determine explosive performance as VOD is a function of the confinement (ground conditions) density and composition of the explosive. Techniques used to measure VOD include resistance wire, time domain reflectometry, simple start stop and fibre optic methods. All these approaches require a cable of some sort to be inserted into each blast hole being monitored and the holes to be fired in a specific sequence. It is time consuming and fairly technical to position the cables correctly to gather the data from each hole. It slows down the hole loading process and increases the number of people on a bench at that time. The equipment and cable limits the measurements to a few holes, typically 5 or less, that are in close proximity. These measurements can generate useful information about the monitored holes but does not provide a full picture of how the explosive is performing across the whole blast and whether any change in performance is noted with changing ground conditions or confinement.

Jan 1, 2019

By Rolf R. Schillinger

It is established to an increased extent that the basic questions about raw material extractions deal with water, dust, noise and vibrations. If it has not been definitely proven that these points won?t lead to excessive environmental strains, attempts at any explanations will meet with disapproval in advance. In order to answer the basic questions about dust, noise and vibrations quality management becomes most important, particularly with respect partly unavoidable emissions of production processes. The specific questions have to be answered within the context of good blasting practices, latest discoveries of the explosives industry, and by use of a Blasting Works Quality- Management, which includes both production quality and Risk-Management. The paper shows a practical way to work out a Quality-Management Program for companies involved in blasting activities.

Jan 1, 2002

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Roger E. Scholl

Data on off-site low-rise building damage from underground nuclear testing at the Nevada Test Site (NTS) of the United States Atomic Energy Commission (AEC) [The AEC has been called the United States Energy Research ant Development Administration (ERDA) since 1975, but because the data presented here were gathered between 1966 and 1970, the AEC rather than ERDA is referred to in this paper.] are available for seven large tests in the period from 1966 to 1970. The data, while sparse, provide an adequate sample for the investigation of motion-damage relationships. Damage in the study is statistically described in terms of the incidence of damage complaints, the incidence of buildings damaged, and damage cost. Using 5%damped response spectrum acceleration amplitude to characterize ground motion, the plotted data fit reasonably well with previous motion-damage relationships established from extensive data available from the 1969 RULISON underground nuclear explosion (UNE) experiment conducted in western Colorado.

Jan 1, 1976

By Kevin Tallent

The use of military-type energetic materials in commercial explosive products is not a new concept. In the United States, the techniques for utilizing significant quantities of surplus military explosive materials by commercial explosive manufacturers dates back to the 1950’s. At times, explosive companies have found surplus military high explosives and propellant materials to be suitable ingredients for their commercial explosive products. The availability of these military-type energetic materials has varied over the past 50 years, as a function of the military’s strategic defense needs and the advances in modern weapon technology. For the most part, the commercial explosives industry has been able to implement methods for safely incorporating military-type high explosives and propellant materials, whenever these surplus materials become available. During the past 5-6 year period, a large amount of military-type energetic materials have once again become available for recycling into commercial explosives. This situation can be attributed to a number of factors, such as the political changes in Europe, the development of more sophisticated weapons systems, and the increased EPA pressures on the U.S. Department of Defense for disposing of surplus energetic materials. As in the past, U.S. commercial explosive manufacturers have made efforts to recycle these surplus materials into their explosive products. This paper describes some of the commercial explosive products that are currently on the U.S. market, which contain rocket and gun propellants as energetic ingredients. Some U.S. explosive companies, such as DYNO NOBEL, ORICA and Slurry Explosive Corporation, have been able to recycle significant quantities of surplus smokeless powder and composite propellants as energetic ingredients into their commercial Blasting Agents. The successes enjoyed by these companies have once again shown recycling into commercial explosive products to be an economically and environmentally sound method for disposing of surplus military-type energetic materials.

Jan 1, 2000

By (Journal for the Fields of Gunpowder and Explosives) Germany (1914 Issues)

RBH Note: The following items are a deviation from the usual content of these articles, but I thought they were kind of interesting from an historical point of view (other than just explosives-history historical.) The interesting things to me are the military-related products, keeping in mind that World War I didn’t start until August, 1914, and then it was kind of an accident of political alliances gone awry. Obviously companies in Germany saw it coming. Of course, all the ads also included dynamite and safety explosives for mining and tunneling as well as the military items.

Jan 1, 2015

By Bill Romanchuk, Real Doucet

Suncor Inc. has been operating the first commercial tarsand open pit mine in the world since 1967. Drilling and blasting operations are required to facilitate overburden removal and tarsand mining by bucketwheel excavators.

Jan 1, 1985

By Klaus G. Hinzen

Seismic observations offer the only possibility for remote sensing of physical processes like shock-front spreading, material crushing and ground movement. A better understanding of these processes will help to increase the economy of blasting. We developed a digital seismic monitoring system for research purposes. The system can simultaneously record up to 64 channels with a maximum sampling rate of 31 kHz per channel. A software package for rigorous analysis of blast induced seismic waves has been developed.

Jan 1, 1989

By H. Bilgin, Sedat Esen

In this paper, the ground vibrations induced by blasting for stripping work at Sekkoy Open Cast Coal Mine belonging to TKI Yenikoy Lignite Mine (YLI) are investigated and the procedures for monitoring and control of ground vibrations are presented. Ground vibration measurements are conducted in the direction of Turkish Electricity Authorities’ Yenikoy Establishment and social facilities because of the complaints and annoyance arising from this site. Forty ground vibration records are taken in this direction and the vibrations are measured in transverse, vertical, longitudinal components together with peak vector sum. After then the scaled distance relationship is determined at 95% confidence value. Further, Fast Fourier Transform analyses are carried out to determine dominant frequencies for both ground and the structures and amplification factors. When the records taken at four different structures together with the ground are evaluated, it is observed that one of the apartment buildings is amplified the amplitude of longitudinal component 4.3 times. The maximum allowable amount of explosive that can be fired safely at this mine is calculated and recommended on. In the determination of safe amount, 95% confidence line, USBM RI8507 and OSMRE criteria, the dominant frequencies of both ground and the structure, amplification factor and the human response are taken into account.

Jan 1, 2001

By Jim Daley

SEE is a dynamic organization composed of people from all facets of the explosives industry who are truly interested in the advancement of that industry. I had been a miner at the Homestake Gold Mine in Lead, SD for 12 years when I decided to obtain a mining engineering degree. The mental and economic consequences of that decision were more severe than we had imagined. The joint scholarship program of the Northern Plains and Black Hills Chapters of SEE provides assistance to several college students each year. I was fortunate enough to receive scholarships from this program twice and this assistance helped me and my family with both monetary and psychological support during times of need so that we could stay focused on the goal of obtaining a degree.

Jan 1, 1995

By D T. Froedge

The state of Kentucky is making some changes in it's blasting program namely instituting a training program for blasters and instituting a new classification of blaster titled "Class A Kentucky Blaster". These changes will take place within the next year and are felt to be of great interest and benefit to those in the blasting industry.

Jan 1, 1978

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lie Company’s new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996