Search Documents

By Sarah Guzzelli, Enrigue Munaretti, Anneliese Botelho, Jair Koppe

Drill and Blast (D & B) is one of the main operations in the mining production cycle, which aims to fragment rock according to a pre-defined plan for proper loading, haulage and processing specifications. In this sense, data from a Brazilian iron ore mine was analyzed, given emphasis on blasthole length, subdrilling and stemming. The D & B report, including mining data such as number of blastholes, length, and diameter and stemming aspects, was analyzed in order to be able to compare these results with the blast design. The study showed significant differences between the designed blasting pattern and that one obtained by the operation. As a consequence, problems such as inadequate fragmentation, incorrect size distribution and loss of energy, were identified. For example, when stemming has a different length than it should have, noise and flyrock can occur, including inadequate fragmentation and vibration in both situations. Therefore, a comparison between the usual D & B procedures and recommended D & B design based on literature reveals the most important deviations and their consequences. The study intends to identify solutions for simple problems, improving D & B operations and safety practices.

Jan 1, 2014

By Vilem Petr

Optimization blast design parameters for rounds used at surface mines, quarries or cast blast has taken on a new importance with the increased the cost of the explosives and electronic detonators. This paper addresses the fundamentals of blast design and optimization explosive energy utilized for fragmentation. This laboratory studies shows that one key variable-the strain energy set up in rock mass by blast vibration – can be used to predict the extent of damage done to the rock strata, the degree of fragmentation of the broken rock, and the velocity of the broken rock. It also shows how the dynamic strength of the rock strata is influence the fragmentation size distribution as well as the blastability.

Jan 1, 2008

By Dale Nies

In the past, cap and fuse has been the only economical and efficient initiation system capable of providing sequential timing, ease of loading and hookup, and unlimited borehole number for backstope rounds. Unfortunately, in spite of these advantages, several negative factors inherent to the system have always been noted. Due to the long, narrow nature of backstope rounds at the Sunshine Mine, the cap and fuse system results in very long, inaccurate delay times. The system was also occasionally unreliable under all the conditions encountered, which in turn could cause potential safety hazards.

Jan 1, 1989

By Rowland Jones

This type of quarrying is very much different from that of established quarries in developed countries, demanding somewhat unorthodox techniques to produce the variety of materials required. The demands on the resourcefulness of-the quarrymaster can be very testing, and produces quite a different breed of individual than what is normally met in managerial status in quarries of developed nations.

Jan 1, 1977

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000

By Charles M. Curtin

A significant advance in nonelectric delay blast initiation has been achieved by Nonel shock tube, an invention patented by Nitro Nobel AB of Gyttorp, Sweden. Ensign Bickford has been licensed by Nitro Nobel to manufacture Nonel in the United States.

Jan 1, 1976

By R. K. Wharton

A European Directive requires that an explosive which is sold or transported within Europe must meet certain essential safety requirements from 1 January 2003. The assessment and certification of such an explosive is undertaken by an Explosives Notified Body and if the explosive meets the requirements a certificate is issued that allows the affixation of a CE mark. The presence of a CE mark ensures the product free access to European markets. The paper examines the requirements of the Directive, identifies those explosives that come within its scope, considers the role of an Explosives Notified Body, and explains the process of applying for certification.

Jan 1, 2002

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By William McFerren, Pragasen Moodley

In contrast to global trends, African, especially South African, surface mining operations have shown a significant rate of adoption of Electronic Detonators (ED’s) over the last few years. Proven benefits of converting to ED’s from pyrotechnic initiation systems have aided this market conversion. These benefits are experienced throughout the mining operation. Benchmarking exercises, prior to the introduction of ED’s, form part of the conversion process and allow for quantifying improvements. Extensive work has been done on quantifying the benefits of converting to ED’s and have shown that results can be reproducible. Improvements have been experienced in many applications and include environmental impact control, improved mining efficiencies, increased cast benefit and improved size distribution. These step changes in blasting results, in conjunction with the adoption of ED technology have aided the rapid conversion of the African surface market.

Jan 1, 2004

By D Larson, M Finger

Chemical explosives may become a key element in many of the in situ energy and mineral recovery methods under development. This paper discusses the potential role of explosives in deep rock mining for resource recovery. Several energy and mineral recovery programs described are an outgrowth of the Plowshare Program and Explosives R&D conducted as part of the AEC/ERDA mission at Lawrence Livermore Laboratory. Several important aspects of the use of explosives in deep rock mining are reviewed. First, the status of knowledge of deep rock fracturing to create permeability underground is discussed. Completely contained blasting has not been a widely applied tool used in the mining industry. We conclude that data available on deep rock fracture is minimal and that the mechanisms that control the processes must be understood before technical and economic feasibility can be established. We also discuss the unusual problems in the selection of an explosive or blasting agent for deep rock applications including emphasis on the functioning at depth and safety aspects. Finally, a brief review of similar activities within the U.S. is given.

Jan 1, 1976

By D D. Garg, D A. Wasson

Open pit blasting in India uses two types of explosives. First there are bulk explosives for wet and dry holes, and there are packaged explosives. The Indian open pit coal mining is projected to use 190 thousand metric tons of explosives in 1995. This volume is projected to grow for the next ten years, whereas the underground coal mining will hold fairly constant.

Jan 1, 1995

By D K. Joyce, B Mohanty

In a previous paper, it was shown that a lack of clear understanding of the role of initiation mode on detonation characteristics often leads to under-utilization of the explosive system in blasting. This is of particular significance since the very large number of explosive initiation practices currently in use implicitly assumes that the blasting performance of an explosive is largely independent of the exact mode of initiation. This paper deals specifically with bulk-loaded and pneumatically-loaded ANFO under various initiation modes in small diameters. These include initiation by booster and detonating cords of various strengths, and combination of cords and boosters. The nature of energy release and energy partitioning between shock and gas energy have been studied in the underwater test as a function of charge diameter. The paper describes the relative merits of various initiation modes for specific charge geometries and confinement, under end- and side-initiated conditions. Guidelines have also been formulated for use in the field to match initiation practice with blasting requirements.

Jan 1, 1994

By Robert Lee, Jay Rodgers, Kirk Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000

By Bill Runner, James T. Ludwiczak

During the last few years, there has been a flood of local, state, and Federal government regulations concerning blasting. Many of the laws and regulations were written by individuals who know little about explosives, the purpose of blasting, or blasting vibration and damage. I feel that the special interest groups responsible for some of these regulations are not trying to regulate blasting, but to stop it completely by unreasonable, non-flexible, regulations. The most recent being the Office of Surface Mining regulations that are already spreading to the quarry industry and will, no doubt, spread to all blasting involving disturbance of the surface.

Jan 1, 1979

By Anders Nordqvist

LKAB operates an underground iron ore mine in Malmberget in the northern part of Sweden. Twelve different orebodies are mined today using both longitudinal and transversal sublevel caving as mining method. The town of Malmberget is located close to the mining area. The need for urban transformation, moving people and houses, is evident for many reasons. The mining methods used have inherent subsidence issues and there are also vibrations from blasting and mine induced seismic events.

Jan 1, 2018

By David Kennedy, Noel Hsu, Miguel Araos

The use of bulk explosive for mining applications started in the 50’s. Since then millions of tons of that material have been transported by road. However during that time, there have been several road incidents involving them. This type of incident has forced the explosives manufacturers as well as regulatory organizations to look for a better classification of explosives in order to regulate the industry as well as to mitigate community concerns over the classification of mixtures of substances that are regarded as precursors to explosives.

Jan 1, 2006

By Donald F. Rapp

Improvements in non-electric initiation systems have given the blasting industry more choices than ever in controlling blast results. By incorporating blasting requirements and system attributes, timing patterns are only limited by the creativity of the shot designer. This paper will discuss the basic groups of non-electric initiation systems, their attributes, and how to select the optimum system for the job.

Jan 1, 1991

By Lawrence C. K Hu

The release of load mechanism during rock breakage by explosives was founded by Dr. T. N. Hagan & published at the Sixth International Colloquium on Gasdynamics of Explosions and Reactive Systems Stockholm, Sweden, 1977.

Jan 1, 1995

By Norm Tienkamp, Normand Martineau

Through the normal course of operation, mine operators are living situations where blast results need to be measured. It becomes the supervisory group responsibility to select evaluation parameters with appropriated and available technics. In Mine Selbaie's case, we have retain the following parameters: rock fragmentation, oversize fragments, rock pile movement, grade rupture.

Jan 1, 1996

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006