Search Documents

By Jim Davis, Calvin J. Konya

The methods used to confine the gases within a borehole can influence the amount of useful energy obtained from the explosive charge. Improper confinement not only wastes energy and raises cost but also can result in airblast, excessive ground vibration, flyrock and boulders. The type of stemming material and amount of stemming used will definitely influence the degree of confinement and the efficiency of the blast. In order to extract the maximum energy from the expanding gases, the stemming plug should never blow out and allow the gases to escape prematurely.

Jan 1, 1978

By Steven D. Knudsen, Dale S. Preece

The spherical element computer code DMC (Distinct Motion Code) used to model rock motion resulting from blasting has been enhanced to allow routine computer simulations of bench blasting. The enhancements required for bench blast simulation include: 1) modifying the gas flow portion of DMC, 2) adding a new explosive gas equation of state capability, 3) modifying the porosity calculation, and 4) accounting for blastwell spacing parallel to the face.

Jan 1, 1992

By D Schneider, H Elliott

The advantages and disadvantages of using inclined boreholes in blasting has been under discussion for a long time. Some recognized disadvantages are that drilling costs, both operating and capital costs, are higher for inclined holes than for vertical ones, and that drilling accuracy is more difficult to maintain. People who have used angled holes in practice, on the other hand, have claimed that the quality of blast results was improved. In fact, their popularity has increased, especially in Australia.

Jan 1, 1988

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By James T. Ludwiczak

The state of Kentucky uses more explosives than any other state in the country. The majority of these explosives are used in underground and strip mines in the well-known coal fields of eastern and western Kentucky.

Jan 1, 1978

By Alan Bauer

During the past several years, the trend to large-diameter blastholes in both open pits and underground mines along with the continuing developments in slurried explosives and delay systems has kept things exciting for the drilling and blasting engineer. This has been particularly so in underground mining, where new mining systems having lower cost and higher productivity have emerged. Crater technology has produced new large-scale methods for resisting front penetration in tar sand mining and also new underground retreat mining methods and methods of raising.

Jan 1, 1978

By Andre Pinsonnault, Francois Lefebvre, Yves Newman

In 1989, Les Entreprises Kiewit Ltee signed a C$32 million contract with the Societe d'energie de la Baie James, on behalf of HydroQuebec, to excavate the intake and tailrace channels for a second powerhouse at the LO-2A James Bay hydroelectric project. The multistage contract included removing three marine rock plugs. The first plug was blasted in April 1990. It was a 43 yards wide, triangular shaped wedge that projected into 18 yards of water. Located at the mouth of the intake channel, it contained over 72,000 yd3 of rock, more than twice the 30,000 yd3 found in most rock plugs.

Jan 1, 1991

By H. Frank Murati, D. S. "Sax" Saxena

The presence of a mobile home park with drinking water wells created a unique geoenvironmental deterrent to the developer’s plans for effective rock blasting, excavation, and development of water management areas (lakes) in connection with the construction of Crown Colony Resort, a residential cum golf course community in southwest Fort Myers, Lee County, Florida, USA.

Jan 1, 2002

By Ron J. Elliott, David G. Otto

This project involved deep blast densification of recent volcanic avalanche debris deposits consisting of a 43 meter thickness of loose clean to slightly silty sand, gravel, cobbles and boulders deposited as a result of the 1980 eruption of Mt. St. Helens, Washington, U.S.A. This project was carried out to enhance the resistance to liquefaction or dynamic settlement of soil deposits under the bridge abutments for construction of the 59.4 meter long South Coldwater Creek Bridge. As this bridge is located close to the Mt. St. Helens fault, it will in all likelihood be subject to earthquakes in the order of 6.5 with expected accelerations of 0.55g. Without soil densification, the bridge would suffer severe structural damage in the event of a significant earthquake.

Jan 1, 1994

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995

By Brian Stump, Chris Hayward

Blasting operations at one copper mine are studied in detail to examine the relation between blast design parameters and near-shot, in-mine, and regional seismic and acoustic observations. Five observational experiments, namely collection of blast design data, near source recordings, GPS synchronized video, near mine recordings and distant regional observations were performed during one week in August. A variety of seismic and infrasound instruments were installed near the shot, on the perimeter of the open pit mine, and at several locations up to 500 km distant. Time tagged video recordings were taken of several shots. Three shots were used in the preliminary analysis, a 350,000 lb pattern with long delays, a 60,000 lb pattern with short delays, and a 256,000 lb pattern with short delays. Maximum peak-to-peak amplitudes of the seismic signals in the mine are not a simple function of the total size of the shot, but are related to the pattern timing. Peak pressures have a less clear relation to peak pressure but match the relative amplitudes of spectra modeled from the pattern design. The predicted spectrum based upon a simple impulse model fits the observed spectrum for ground acceleration measured near the pattern and explains why in this case a pattern of 60,000 lb results in the same seismic disturbance as the 350,000 lb pattern.

Jan 1, 2002

By Mike Koehler

An underground mine that produces aggregate limestone was in operation for approximately eight years when geological changes resulted in dangerous rock falls. The roof in the mine was not bolted; therefore, the drilling and blasting program was called upon to maintain roof integrity. Drilling and blasting were analyzed and modifications were adopted to stabilize the roof. Initial changes were made in the drilling equipment, drill pattern, explosive type, and timing. Any amendments made, after the initial phase, were made individually so it would be easy to discern which changes worked.

Jan 1, 2002

By Bjorn Engsbraten

Explosive charges have been fired under defined conditions in a closed tunnel. The explosives have either been detonated in a steel tube or a single borehole. In the latter case dimensions, -loading density and confinement have been chosen to correspond to common practice.

Jan 1, 1980

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

Test blasting was carried out to study the flying characteristics of rock mass caused in bench blasting. The quantity of explosives was increased from 7.6kg to 9.1kg and the Minimum burden was changed from 131mm to 451mm. The effect of condition for the characteristics of fly rock were considered. The fly rock was observed using the high-speed camera and video to study the flying characteristics of the rock mass caused in the bench blasting. Numerical simulation of fly rock was carried out using DDA (Discontinuous Deformation Analysis) method. It was clear that the DDA method can be applied in the simulation of fly rock caused in bench blasting.

Jan 1, 1997

This paper describes experience in designing and implementing casting blasts over the past fifteen years. Important design parameters such as powder factor, burden and spacing, blast pattern geometry, front row burden and toe distance, pit width versus height, blast length, explosive selection, millisecond delay timing and tie-in types are discussed.

Jan 1, 1995

By Ginn Huh

The blasting work to construct a subway in Seoul, Korea have often caused increased neighbor’s complaints because of ground vibration. In order to prevent the damage to the structure, it was necessary to predict the level of blasting induced vibration and to determine the maximum charge weight per delay within an allowable vibration level. The effect of blasting pattern, rock strength and different explosives on the blast-induced ground vibration was studied to determine the maximum charge weight per delay within a given vibration level. The blasting vibration was measured from 10 sites along the subway line in Seoul and an empirical particle velocity equation from over 100 test data was obtained, V=K(D/W1’3 )-” , where the values for n and K are estimated to be 1.7 to 1 S and 48 to 138 respectively.

Jan 1, 2000

By Brent Blanchard

An emergency demolition project related to a bizarre plane crash has reportedly set a new world record for the tallest structure ever explosively demolished. On Sunday, April 22, 2001, 38-year old Gilbert Paquette was killed when his singleengine Cessna 150 struck a 1,217-foot tall communications transmission tower while flying in heavy fog over a remote region of upper Quebec Province.

Jan 1, 2002

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By J R. "Dick" Daniel

Over the past several years, the Hercules Technical Service Group for the Explosives Department has produced a series of programs for the TI59 programmable calculator dealing with explosive application problems. These programs have been made available to both our internal staff and to the Hercules explosives distributor organization. Several of these programs have found good acceptance and wide usage.

Jan 1, 1984

By Gregg R. Gitschlag

There are more than 4,000 oil and gas structures present in the U. S. Gulf of Mexico. Approximately 100 structure removals occur each year and 66% of these are removed with explosives. From 1993-1995 an intensive study was conducted on the fish kill resulting from the explosive removal of 6 platforms off the Louisiana coast in water depths from 14-28 m (45-92 ft). After explosives were detonated, all floating fish and a sample of the dead fish which sank to the sea floor were collected.

Jan 1, 1997