Search Documents

By J. Silva, T. Worsey

The Worsey-Silva equation determines the optimal row timing for the smallest fragmentation and allows fragmentation models to be adjusted due to row timing. The equation utilizes the concept of dynamic confinement to determine when the best time to fire the next row or sequence series would be if the smallest fragmentation is desired. Full-scale testing was conducted at an aggregate quarry in Ontario to support the theory and equation. The full-scale testing comprised six (6) blasts, two (2) different contractors, and three (3) different sequences. The test parameters were kept consistent, besides changing the timing between sequential charges to explore the timing sequence’s influences on fragmentation. From this research, the theory of dynamic confinement relating to row timing was discovered, and the equation to determine the optimal timing for the smallest fragmentation was derived. An equation to adjust fragmentation based on row timing was derived from the full-scale testing and literature review. The Worsey-Silva equation can be used with other fragmentation models as it takes the fragmentation results from the other models and adjusts them based on the row timing used. The paper explains the theory behind the equation, the research supporting the findings, and the developed Worsey-Silva equation for row timing

Jan 1, 2024

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By David La Rosa, Matthew Craft, Lee Julian

Rules of thumb are ubiquitous in blasting. Typically presented as ratios, they assist with the initial assumptions of blast design and provide guidance for best practice. Examples include the blast hole diameter as a function of bench height, and stemming length as a function of hole diameter. The most common rules of thumb were developed in mid-20th century and it is important for a blaster to know if the rules of thumb are still reliable.

Feb 6, 2023

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By Tapan Goswami

The expectation from the blasting engineers and shotfirers is often that explosives will perform optimally at all times. However, in reality, non-ideal situations exist on mine sites and occurrences of poor explosives performance are common. Often the cause is difficult to identify. Having a good application technique and analysis skills will minimise the risk of poor performance. This paper will discuss the experiences gained by the author while blasting in the Hunter Valley, Australia.

Jan 1, 2003

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By Sayantan Chakraborty, Kaushik Dey, SaKaushik Dey tyabrata Behera

Drilling and blasting is a popular excavation technique in the drift of underground mine. Faster completion of drift reduces the gestation period and thus longer blast pulls are attempted with longer drill holes. This compels the blasters to initiate higher charge quantity with higher confinements and ultimately results into blast-induced cracks beyond the desired periphery line of excavation. Assessment of the extent of these crack networks is difficult and often neglected. Near-field ground vibration models are often used as damage predictors (Dey, 2007, Yang et.al 1993, Holmberg et. Al 1979) but not necessarily deals with the positions of the cracks. Qualitative measurement of actual damage extent often measured using some geophysical tools, namely, P-wave velocity (Tezuka, 1995), seismic imaging (Dey, 2011), bore hole pressure monitoring (Brent and Smith, 1996), electrical resistivity (Grady and Kipp, 1993), GPR (Adams et.al, 1993) etc. Ground Penetrating Radar (GPR) is a similar geo-physical tool, which uses Electro-magnetic (EM) pulse for characterizing the medium. Similar to other geo-physical tools, GPR also comprises of a transmitter and one/multiple receivers to generate the EM pulse and receive the same after reflection/refraction from the medium(s) respectively. After its development in 1970s, GPR gained increased popularity due to its application in many important fields, namely, identification of buried objects, geological characterization, identification of geological disturbances etc. Thus, it is felt that GPR technique can be used to detect the invisible cracks inside the rockmass from the rock surface (wall and roof) itself. Understanding the same, field experimentations are carried out in an underground manganese mine in Central India, which operates on the ‘cut and fill’ method of mining at a depth of around 300m from the surface. Wedge cut blasting is carried out in the horizontal drifts of the mine using suitable blast design. A 1.6 GHz antenna was used for the GPR scanning, in which GPR transmitter transmits signals predominantly of the said frequencies. The signals get reflected back from any type of interfaces between materials in the target area, with different dielectric properties and is received by the receiver part of the ‘trans-receiver’ antenna and memorized in the Data Acquisition Unit (DAU). The data acquired is processed using a software. Ground vibration monitoring of the blasts are also carried out to develop a vibration predictor. The numerical analysis of near-field vibration predictor model results into the estimated vibration levels at the point of identified cracks. Introduction

Jan 1, 2019

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008

By David N/A Doucet, Colter N/A Angell, William N/A Joa, Kyle N/A Wagner, Catherine N/A Johnson, Marty N/A Langenderfer

The Kingery-Bulmash (K-B) equations are a widely accepted means of predicting air-blast parameters from surface explosive detonations. The parameters predicted from these calculations include incident and reflected pressure, time of arrival, shock front velocity, incident impulse, reflected impulse, and positive phase duration. K-B calculations are based on curve fitting of experimental data and can be used to predict air-blast parameters for explosive weights from less than 1 kg (2.2 pounds) up to 400,000 kg (440.9 US Tons), and ranges of 0.05 to 40 meters (1.9 inches to 131.2 feet). The K-B equations can also determine the parameters for multiple explosive types using scaled distances and relative equivalency to TNT. An experiment was designed to demonstrate if the measured results for incident pressure, time of arrival, shock front velocity, incident impulse, and positive phase duration equal the expected results reported for the detonation of a small quantity of explosive determined by the K-B Calculator. Three surface-detonated 300-gram (0.66 pound) hemispherical charges of Composition C-4 were observed via high-speed imaging and hydrostatic pressure monitoring. The hydrostatic pressure generated from each charge was measured via piezoelectric pressure transducers at a scaled distance of 10 from the charge epicenter, and at elevations of 0.30, 0.61, and 1.22 meters (1, 2, and 4 feet) above ground level. Variances in experimental values from the K-B predicted values were recorded for each measured blast parameter. Time of arrival, which was redundantly confirmed through high-speed imaging analysis and hydrostatic pressure monitoring, showed the highest deviation from the predicted values at more than double the K-B predicted value. This report compares the observed blast parameters from the test series with the expected blast parameters from the Kingery-Bulmash Blast Parameter Calculator. Differences between the experimental and predicted values are reconciled through analysis and discussion of testing conditions, instrumentation setup, and scaling methods.

Jan 1, 2019

By Adam T. Young

This paper will describe the process of using low density bulk emulsion as a means to maximize the production of an oversize or “rip rap” aggregate size range (8 inch to 72 inch) that the quarry customer has a market demand for. It will also discuss the pre-blast and post-blast metrics used during the product trials and evaluation.

Jan 1, 2017

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By Robert Hopler

Of the common causes of the larger mine accidents, such as falls of roof and coal, gas and dust explosions, mine fires, and the misuse of explosives, all of which are often closely related, each must be studied and fought in a manner peculiar to itself. The last mentioned, the misuse of black powder and other explosives, is sometimes considered the least important of these causes of mine accidents; but its importance is much greater than the statistics indicate, for the reason that the misuse of explosives is the true cause of many of the fatal mine fires, gas or dust explosions, and falls of roof that are credited to other causes.

Jan 1, 2012

By Sven-Erik Johansson, Gosta Rundqvist, Donald Jonson

In Stockholm a new road traffic system called Södra Länken (Southern Link) will be in operation in late 2004. The total length of the road system is 6 kilometres of which 4,5 kilometres run through tunnels under suburbs immediately south of Stockholm inner City. The new traffic tunnels together with existing Metro tunnels, which mostly are in rock, will be the determining factor for blast design for many projects in the future. To set reasonable and safe permitted vibration levels the Swedish National Road Administration, Stockholm Region and Stockholm Transport Rail System have together financed a project to determine guide levels for blast-induced vibrations in traffic tunnels in rock. The purpose of the project has been to establish guide levels that are appropriate for different types of rock tunnels.

Jan 1, 2004

By Steve Dillingham

Here in the United States, as well as around the world, pose a daily dilemma - to wash or not to wash. Let’s face it, all trucks, especially our industry work horses - bulk trucks - get dirty. We all know that these units can be very expensive and washing them keeps your business investment looking new, improves public relations, fuels company pride, and facilitates equipment safety and preventative maintenance inspections.

Jan 1, 2001

By Keith Maki

This paper details a simple substitution of precise electronic timing in the holes for standard pyrotechnic delays. In addition, we wanted to use two electronics in bottom and top to test the colliding shock wave theory. It also discusses the difficult loading conditions on the Iron Range of Northern Minnesota. No preliminary analysis (Signature Hole waveform analysis) was done to determine the most favorable blast timing for fragmentation increase or vibration reduction.

Jan 1, 2007

By Ian Bell

This paper investigates fragmentation in an aggregate quarry using the fragmentation-energy fan concept. Six blasts were monitored, located one behind the other in the same quarry area. The rock structure was blocky, the water level and the usage of explosives were variable within and between the blasts. The powder factor above grade was between 0.28 and 0.44 kg/m3 (0.47 and 0.74 lb/yd3). Fragmentation of the plant feed was measured using an online digital image analysis system and three belt scales. The oversize material that was not directly fed to the plant after the blast corresponds to 3‒9.3 % of the total. Data from image analysis was used to build the size distribution in the coarse range (fragments above 120 mm), and the passing fractions at 120 and 25 mm (4.72 and 0.98 in) obtained from belt scales data were used in the range 120‒25 mm (4.72 ‒ 0.98 in) . The non-dimensional percentile sizes between 10 and 90 % for each blast are described through power functions of the powder factor above grade; the model coefficients are statistically significant. From them, using the principles of the fragmentation-energy fan and the Swebrec distribution properties, the fragmentation can be expressed in terms of the powder factor by means of five parameters: the fan focus coordinates and the three parameters of a function of the exponents vs. the percentage passing. The model shows a good capability to describe fragmentation.

Jan 1, 2019

By Norman Paley, Finn Ouchterlony

Detailed fragmentation data for different blast delay timing tests at the Red Dog mine in Alaska are analyzed. This work is a continuation of previous work in which the crusher output was found to be better described by the three-parameter Swebrec function than by the Rosin-Rammler function. For a crusher model, the x50 variable sufficed to describe changing crusher input while b and xmax could be considered fixed. For the crusher output from aggregated stockpile rock, as measured by digital image analysis using Split-Online, the constancy of b was not as apparent. In this paper detailed stockpile data, single Split data series, and sieved belt cuts of crusher product are analyzed using the Swebrec and truncated Rosin-Rammler functions. The variability of b is confirmed. By using specific fraction passing sizes a shortcut is presented that removes the need to do curve fitting to determine the three Swebrec function parameters.

Jan 1, 2013