Search Documents

By J Edmund Hay, Harry C. Verakisl, Richard J. Mainiero, John J. Mulhern

As the first stage in the rulemaking process, MSHA prepared requirements for the approval and use of permissible explosives and blasting items in underground coal mines. These draft requirements known as "preproposals" were announced in the Federal Register in mid-1984. The draft requirements on the use of explosives were written as a revision to Title 30, Code of Federal Regulations, Part 75, Subpart N. The draft requirements for approval of permissible explosives including sheathed explosives for unconfined applications, approval of water stemming bags, approval of detonators and approval of blasting machines were prepared as Parts 15, 16, 17 and 25 respectively.

Jan 1, 1985

By Thomas L. Barkley

This paper describes an unusual design for a 12 foot diameter, 30 foot deep circular shaft shot in a close in urban environment less than 100 feet from occupied structures. It uses diagrams, video footage, and vibration results to describe a 3 deck, 17 hole burn round used to pull 17 feet in one lift.

Jan 1, 1994

By J Silva Castro, W C. Wedding, B T. Lusk, J Calnan, E G. Morris

The emergence of electronic detonators for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. This paper reports on an independent study quantifying the accuracy of two electronic and two non-electric systems in which 674 detonators were tested. This research aimed to determine the accuracy of commercially available electronic detonators as compared to non-electric shocktube systems. Each system was tested over the viable ranges of delays available. Statistical models were then applied to quantify the scatter present in each system. Suggestions for the use of electronic detonators are made from the findings of this work. This work was made possible through funding from the United States Department of the Interior Office of Surface Mining Reclamation and Enforcement.

Jan 1, 2012

By Gary B. Hemphill

Each year the demand for precision blasting increases due to the reduction in the amount of prime land. More site preparation and hone building requires blasting than they did a decade ago, Because of this increased need for blasting in more populated areas, the need for blasters and engineers knowledgeable in work involving blasting nets has increased.

Jan 1, 1978

By Bengt Niklasson

"A test stope at the Luossavaara Research Mine in Kiruna, Sweden,was divided into four different modules in which various hole patterns and explosives were tested in order to evaluate:1. The optimum combination of explosive and hole pattern2. The resulting fragmentation3. The damage to the surrounding rock4. The application techniques of the VCR mining method"

Jan 1, 1985

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines fired seven test blasts in a 22-ft bench of limestone, screening the material to investigate the influence of explosive type and between row delays on fragmentation. Four 4-hole, single-row test shots were conducted evaluating dynamite, ANFO, emulsion, and a 60-40 emulsion-ANFO mix. Three 12-hole shots, with three rows of 4-holes, evaluated delays between rows of 24, 36, and 120 ms. Accurate in-hole electronic delays were used, firing within 1.5-ms of the nominal delay. All seven shots had a 6- to 7-ft burden, 10-ft spacing, with a hole diameter of 3-1/2 in fired on a 12-ms delay between holes in the row. The tests were instrumented with strain gauges grouted in the burden region examining stress wave and gas pressure effects. Fiber optic probes were used to confirm timing and to obtain detonation velocities.

Jan 1, 1989

By Minoru Kawamura, Yukio Kato, Yoshikazu Hirosaki, Satoru Suzuki

A wireless blasting system for tunnel construction which consists of a loop antenna, oscillator and blaster, has been developed. The basic technology of this method had been studied in the 1970s to develop a wireless initiation system for undersea blasting and has been successfully used as a Remote Controlled (RCB) system in the Honshu/ Shikoku Bridge construction project in Japan.

Jan 1, 1998

By Cam B. Grundstrom

This paper will describe blast design modifications that have been made at the Island Copper Mine, near Port Hardy, British Columbia. To date, two additional designs have been implemented in an effort to reduce final wall damage and increase productivity. The typical blast patterns in use at Island Copper were monitored in an effort to build up data to which new designs could be compared.

Jan 1, 1994

By Conny Postupack, Jim Petrunyak, John Loope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four methods of reclamation now in use are reviewed, and their advantages and disadvantages are noted. Guidelines for selecting a particular method are offered in terms of applicability under varying geologic, economic, and technological conditions.

Jan 1, 1987

By Doug Johnson

This paper reviews the field implementation of R & F Coal's blasting optimization work concerning analysis, prediction, and control of overburden blasting vibrations using site specific measurements and state-of-the-art computer technology. Blasting personnel at R & F Coal had the opportunity to work jointly with Otto Crenwelge of Shell Development Company in his test studies and to later be instructed in the procedures involved in optimizing vibration frequency.

Jan 1, 1988

By Conny Postupack, Jim Petrunyak, John Hope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four xchods o f reclsnacisn now in use are reviewed, and their advantages and disadvanrages a r e nocea. Guidelines for seleccrng a particular method are offered in terms of applicability under varying geologic, economic, and technological condirions.

Jan 1, 1989

By Sally Lynn Zadra

"In May, 1994, Echo Bay Minerals - McCoy/Cove Mine petitioned for approval to recycle used oil formanufacturing ANFO. Recycling oil in this way will result in a cost savings for the minesite as well ashaving a positive environmental effect The petition has met the approval of the Bureau of LandManagement, the Nevada Department of Environmental Protection, and has received tentative approval from the Mine Safety and Health Administration."

Jan 1, 1996

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

In March of 2001 Barrick Goldstrike Mines, Inc. began evaluating the potential benefits of electronic detonators at the Betze Post open pit gold mine. The original evaluation focused on increased fragmentation, and excavator productivity. During the original evaluation there was an attempt to quantify mill throughput. Early tests indicated that there would be a benefit to mill throughput, however management was hesitant to take on the added cost of electronic detonators based on the initial evaluation. In early 2002 a decrease in mill throughput was being forecast as a result of harder ore being encountered. As a result of the initial electronic detonator evaluation a team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative. This initiative was targeted at improving mill throughput as the harder ores were encountered. Batch tests were conducted to determine if adjustments to drilling and blasting in the open pit could increase mill throughput and justify a 50% increase in drilling and blasting costs for the harder ore material.

Jan 1, 2004

By Jin Jingzhi, Wang Xuguang, Guan Li, Li Jianjin

Emulsion explosives are gaining a wider and wider commercial market and are displacing other composite slurry technologies. However, the grease-like state and essential thermodynamic instability of emulsion explosives cause inconvenience in production, transportation, storage and use and lead to gradual changes in performance. Emulsion powder explosives are designed to avoid these disadvantages. The formulation, process and properties of emulsion powder explosives made through a spin flash technology are described in this paper.

Jan 1, 1997

By William B. Lee, James J. Jurmu

The Cleveland-Cliffs Iron Company operates three open pit iron mines on the Marquette Iron Range of Michigan's Upper Peninsula. Open pit iron ore mining began in the area in the 1840's. Underground mining was predominant from 1860 through 1960. Large scale low grade-open pit iron ore mining began in the early 1950's with the establishment of the Humboldt Mine, concentrator and pelletizing plant. This pit operated until 1970, when the reserves were exhausted.

Jan 1, 1986

By J Mensah, G C. Sen

Often large boulders of rock have to be fragmented in civil or mining engineering operations. These oversize boulders are encountered after primary blasts in both surface and underground excavations of minerals. Various methods are employed to break large boulders into a manageable size for loading and crushing. These methods range from mechanical breaking (such as drop-ball and hydraulic impactor) to the use of explosives. Apart from these, static agents (such as expanding chemicals) are used in special circumstances.

Jan 1, 1989

By Tony Rorke, Tamara Wiseman

Due to the advancements in technology it becomes easier to obtain accurate measurements for mining, quarry, and construction operations even in the most remote places. The use of off-the-shelf photogrammetric imaging technology and unmanned aerial vehicles (UAVs) are becoming more common in the mining industry for blast design and surveying. Pattern optimization, face profiles, pre and post blast volumetric, stockpile measurements and mine mapping are all areas where these technologies can be used with ease.

Jan 1, 2015

By D. Bartley, R. McClure, W. Reisz

Ever since the 8ms criterion was developed in the early 60’s there has been an ongoing debate among many blasters as to its actual value in controlling ground vibration. The perpetuation of the myth surrounding the 8ms window can be partly attributed to its simplicity and convenience as a means for regulatory compliance. Unfortunately, the mindset that many blasters have adopted has hindered the development and use of more effective techniques and in many cases can actually be counter productive to vibration control.

Jan 1, 2006

By Paul V. Sterk, James Wieser

Mining in underground situations requires constant change due to changing ore bodies and economics. The Homestake Mine in its 122 years of existence has gone through numerous changes due to these factors. Recent sustained low prices in gold and ore bodies that are smaller or within mined out areas have forced the mine to reevaluate how these ore blocks will be mined. This paper will describe the design, drilling, and blasting of a complex ore block using the blind raise uphole bulk mining method.

Jan 1, 1999

By Kenichiro Yamamoto, Masaharu Murakami, Toshio Matsuzawa, Yoshiyuki Ikeda

In a series of tests, we examined the dynamic shock resistance of Emulsion Explosive in water and compared it with that of Dynamite and Slurry Explosives. Both the distance between donor and acceptor charges and the delay initiation timing of the acceptor charges were varied. The resistance to dynamic shock varied with the properties of the explosive. In the case of emulsion explosives, there seems to be a certain proportional relationship between the critical detonation distance and the delay initiation timing. Some blasting results with emulsion explosives are described.

Jan 1, 1983