Search Documents

By Vitor Barcelos, Eduardo Elói, Gabriella Vaz, Davi Oliveira, Leandro Silveira

Following a routine production blast at Vale S.A.'s Itabira Mine in the Quadrilátero Ferrífero region of Minas Gerais, Brazil, nearby residents registered complaints about blast-induced vibrations. Analysis of the blast footage revealed that multiple blastholes were detonated simultaneously, resulting in a higher-than-expected charge per delay, ground vibration and cratering even though the electronic delay timing was configured correctly. Subsequent blasts within the mine's soft schist region confirmed the occurrence of sympathetic detonation. Mitigating or eliminating this phenomenon is critical for the mine's operation. Two dynamic pressure tests were conducted using carbon resistors together with typical VOD monitor maintaining the standard booster, electronic detonator, and a blend of 70% emulsion with 30% ammonium nitrate explosive. The tests involved increasing the distance between the central hole (detonated first) and the four surrounding holes in a five-hole sequence. Unfortunately, sympathetic detonation occurred in all these tests. To address this issue, a new explosive with a lower density and detonation velocity was tested. This approach proved promising, as no sympathetic detonation occurred. By leveraging the data obtained from this study, engineers can now identify situations at risk of sympathetic detonation and implement preventive measures, such as selecting the appropriate explosive and recommending safe minimum burden and spacing settings as well as confinement level for each blast while maintaining the desired level of rock fragmentation.

Jan 21, 2025

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By Dave Kay, Young-Suk Song

To meet the needs of South Korea's rapidly expanding economy, a large number of infrastructure projects are under way to improve transportation efficiency within the nation. These projects include high-speed rail links between major population centres and improvements to the road network. Being densely populated and geographically mountainous, infrastructure development in Korea requires a significant amount of tunnelling. Owing to the predominantly hard granitic nature of rock, drill and blast is the preferred method of tunnel advance. The Korean tunneller, however, faces the same pressures as those of his international counterpart in that both cost and production targets need to be achieved while meeting expectations of both community and regulator.

Jan 1, 2005

By A. Andrades, E. Arias, Y. Pizarro, J. Alarcón

Division Ministro Hales - Codelco (DMH) is located at 2600 meters above sea level, 10 km north of the city of Calama, Antofagasta region, Chile. In operation since 2010, it corresponds to a porphyry copper deposit that is exploited by the open pit mining method. The ore is mainly composed of sulfides, which is concentrated by comminution processes such as crushing, SAG milling and ball milling to liberate the mineral particles, and then separated from the waste (concentrate) in flotation stages, including a concentrate regrinding stage. Reports from the DMH processing plant area have identified a decrease in fine copper recovery, with the first hypothesis being the high percentage of ultrafine particles (% <45µm) in the flotation feed. Due to the above, DMH & Orica decided to carry out activities to identify the controllable variables that can impact the generation of low size particles in ore and adjust them to reduce the percentage of fine material generation, with special focus on the Drilling and Blasting processes. Based on the data provided by DMH, we evaluated what could be integrated to make an analysis. The different attributes associated with the ore and their effect on copper recovery were evaluated. In parallel, at the mine, a fragmentation measurement campaign was carried out at the loading faces and granulometric analysis of the drill cuttings. Once the correlations between the attributes and copper recovery were identified, hypotheses were established and reviewed with the Drilling & Blasting, Geotechnical, Geology and Process Plant areas. With the validations of the hypotheses and the results of the in-mine (cutting) measurements, we proceeded to review the criteria for the classification of Blastable Geotechnical Units and their associated D&B designs. Using software and the Crush Zone Model (CZM) tool, which considers rock and rock mass parameters, scenarios for various D&B design proposals were simulated with the objective of reducing the generation of ultrafine particles from the blasting process. Next steps include trial blasting with the D&B design recommendations, which will require follow-up to the flotation process to identify the impact on the reduction of ultrafine material from blasting.

Jan 1, 2024

By Jim Peterson, Ricardo Freire, Mason Biernat

Variable nature of rock and face conditions, varying execution and changing nature of blasting are making ongoing optimization challenging. Intelligent planning and on-going analytics are required to mitigate variability and convert blasting into a predictable outcome by use of technology. Blasting operations generate a huge amount of data which can be used intelligently for optimization. In this paper, details are provided of a system which is used for blasting data collection in the field – Key details around blast parameters, explosives, initiating system details, video, photographs, vibration and fragmentation are collected in a cloud-based platform. Data can also be collected through a mobility device in the field (even without internet connectivity) and synchronized with cloud-based system. Also, data from various sources can be imported in excel formats in the software including from upstream and downstream processes from blasting. App also gives indication about exceeding of vibration, air blast overpressure, fragment size etc. Thus, making it possible to perform QA-QC before charging and deciding initiation timing and sequence at the blasting site. The data can be processed and analyzed to spot trends, help predict events, and formulate strategies at the design and execution stage. Data gathering of blast parameters, explosive used processing and analysis can be used to optimize operational efficiency, improve safety and environmental controls.

Jan 1, 2019

By Sanna Mustonen, Seppo Mellanen, Mellanen, Pekka Kantia

In Finland Posiva Oy (Company) is responsible for implementing the final disposal programme for spent nuclear fuel of its owners. Company is preparing for the geological disposal in Olkiluoto crystalline bedrock. Excavation will be executed using drill and blast method. Method unavoidably causes variable excavation damaged zone (EDZ) on tunnel surfaces. The EDZ constitutes a risk for long term safety and therefore good control methodology of the blasting technique is required. The thicker the EDZ, the greater is the likelihood for detrimental transport pathways for ground water to transport radio nuclides, should those be present.

Jan 1, 2016

By Alejandro Berrios, Matheus DaSilva, Erick Siqueira

Vazante mine is an underground polymetallic mine that produces zinc, lead, and silver, which belongs to Nexa Resources in Minas Gerais, Brazil. The mine, a sublevel stope underground mine, mainly applies two subvariants: VRM – Vertical Retreat Mining and Open Stope. In a specific place of the mine, the geology allowed the design of a production stope with larger dimensions than the standard stopes, commonly called Super Stope. At this place, the plan was to apply both sublevel variants simultaneously. This mining block comprises rings in two different levels, with access by two ore drives on each level; the dimensions would be approximately 50 meters high, 50 meters long, and 35 meters wide. Opening the Free Face to mine the whole Stope was a challenge due to operational issues, such as hazard risks from loading over void space, exposure to uncontained places, and the impossibility of implementing the optimal blast sequence. Wireless blasting initiators have gained popularity recently due to their convenience, safety, and efficiency. This initiation system was applied to preload all the rings required to open the Free Face, ensuring a safe and optimal blast sequence. Wireless initiation prevented hazard risks, enhanced the blast sequence to guarantee the required void space, and optimized the equipment's operational cycle. The blast crew carried out the activity without exposure to the risk of loading over void space. The wireless detonators also avoided after-blast activities, which were required to provide secure access to the blast crew, optimizing the operational cycle.

Jan 21, 2025

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue.

Feb 1, 2020

By Cesar Guerra, Alejandro Rojas, Dr. Jhon Silva, Luis Velasquez

The ANN method is applied to predict the P_80 size in one open pit gold mine in Peru. The ANN was implemented in Matlab programming language, and the results from the ANN are compared with data obtained using photo-fragmentation analysis software.

Feb 1, 2020

By Glenn Tobin

The overarching goal in modern drill and blasting operations is that of optimising mining operations to achieve higher levels of productivity, safety, profitability and sustainability. Air decking, a technique used in drill & blasting to optimise explosive product use while achieving a target rock fragmentation1, is a technique that when executed correctly is proven to achieve consistent results independent of rock strength and the position of the holes (single, multiple, vertical, slanted), as well as being proven to reduce super-fragmentation (under-size or fines) while able to achieve optimal fragmentation, especially in the stemming zone2. The ‘shock absorber effect’ if the air deck reduces ground vibration and air blast3. Additionally, the practice of loading explosive product directly in saturated ground without dewatering or lining prior is an increasing global trend.

Jan 1, 2012

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue. In spring of 2016, the Inauen Schatti company of Switzerland started the development of a flyable RACS deployment box to complement their 2 stand alone tower systems. To go along with the new flyable deployment box, a new S-Load charge carrier was developed. The newly developed and patented S-Load explosive charge for the LM32 RACS system features a mechanism which combines the explosive and priming material just before the blast. These are stored separately during transport and storage in the LM32 RACS deployment box. The S-load is divided into two parts. The upper part contains the plastic bobbin and ignition sequence (impact pull wire igniter, safety fuse and #8 blasting cap), whereby the explosive material and detonating cord are positioned in the lower part of the explosive container. The explosive material and ignition sequence are separated by a certified housing during transport and storage. The key idea of the S-Load system was to achieve a maximum level of safety by keeping the priming components separate from the explosive material until just before detonation. Because of this the S-Load and the LM32 tower remains safe during transport by helicopter or when being stored in the deployment box on the mountain side in the avalanche start zone.

By Soseol Kim

A high-performance Emulsion-based booster explosives has been developed that can be used as a booster for bulk explosives. Currently, Pentolite booster, which is mainly used as a booster for bulk explosives, has a high risk of accidents due to the sensitivity of its raw materials PETN and TNT, and has a low melting point, making it impossible to use it in high-temperature ground. The Emulsion-based booster was developed to maximize the Velocity of Detonation (VOD) while elimination the shortcomings of the Pentolite booster. The VOD of the Emulsion-based booster is about 6,500m/s, so it can maximize the performance of the bulk explosive. In addition, it can be used in high-temperature ground and does not cause accidental detonation due to the external environment. In this article, the performance of the Emulsion booster was verifies through comparative test blasting of the developed Emulsion-based booster and Pentolite booster.

Feb 6, 2023

By Jason Rock, Rob Thompson, Lee Julian

This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

Feb 1, 2020

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By Eric Reale

The New York City Department of Environmental Protection (DEP) is currently building City Water Tunnel #3 beneath the city. The purpose of this tunnel is to improve water distribution to the city and to allow the DEP to inspect the older tunnels and make the necessary repairs. These older tunnels have been in continuous operation since the early 1900's. Construction on the Third Tunnel is planned in four stages. The Nelson Street Shaft, which is the focus of this paper, is part of the second stage.

Jan 1, 1989

By B. Corrêa, M. Cavalcante

A large open pit iron ore mine in Brazil, which has a heterogeneous lithology, faces a challenge in defining drill and blast patterns to achieve the expected results. The mine needed to obtain an automated representation of the fragmentation curves and correlate them to the respective blasts, lithologies and quality parameters, seeking the continuous optimization of the fragmentation process and its benefits to the subsequent comminution processes. Trials were carried out for 5 months to demonstrate the functionality of an autonomous fragmentation monitoring system that analyzes the granulometric curve of the material throughout the muckpile and makes the results available online and in real time. The system, which contains a binocular camera, a processing unit and an antenna, was installed in a shovel, to evaluate the following KPI's: monitoring failures, monitoring capacity, physical availability and reportability of oversized boulders. The system analyzed 33,060 samples, with an average capacity of 285 photos every 24 hours, 127 during the day and 158 at night, all measured, analyzed, stored, and made available on its online platform, reporting 223 alerts of P80 above 400mm (15.7 in) and 38 particle sizes above 900mm (35.4 in). The inactive and operational hours of the monitoring system corresponded, respectively, to the idle and worked hours of the shovel, according to dispatch data. There were no camera or processor failures, and rain, dust or poor internet conditions did not impact sampling and fragmentation analysis, indicating 100% physical availability of the system. The autonomous monitoring analyzed 139 times more samples compared to the currently used manual method. In addition to increasing sampling representativeness and automating the process, it increases the safety, quality, and productivity of granulometric analysis, eliminating the exposure of people in the mine and human bias in the analyses. Additional analyses were performed by correlating digitally centralized drill and blast data, data from autonomous drills and fragmentation results. Automated obtention of granulometric curves favors quick decision-making and optimization of blasts to achieve better results in productivity and cost reduction in the plant and mine operation. The autonomous fragmentation monitoring system met the need presented by the mine, proving to be a key tool in continuous improvement projects, including Mine to Plant.

Jan 1, 2024

By A Tawadrous, P D. Katsabanis, S Kim

A series of small scale tests, have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite, Barre, Stanstead and Laurentian, were tested. The charge consisted of detonating cord placed in five holes with water as a coupling medium, or concentrated charges of equal mass of high exolosive, fully stemmed or air decked. Powder factor was varied from 0.39 to 1.17 kg/m3. Charges were detonated simultaneously or with a small delay and in some experiments, detonation waves collided in the middle of each borehole. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different levels of impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using standard Bond mill grindability tests. The experiments generally showed increased softening of the rock with powder factor, manifested by the increasing initial slope of the relationship between t10 and impact energy. The rate of change of the initial slope decreased with increasing powder factor. Changes in the work index were small and consistent in trend with the results of the single fragment impact characterization tests. Charge configuration, timing as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2009

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"This document investigates a newly developed technique with the objective of improving terrain triangulation models (horizontal/sub-horizontal and vertical/sub-vertical terrains), mainly blast free faces. The algorithm uses multi-linear regressions to generate the best point cloud projection plane by applying the residues modulus minimization so as to create the finest 3D triangulation model. A change of base is required to create a new set of coordinate axis and generate completely new projection planes. The projection plane residue analysis is inferred in order to avoid or reduce the outlier points. The dataset is composed of 12 terrain models obtained from photogrammetry and a 3D Laser equipment thatgenerates georeferenced cloud points. This new technique is validated by the analysis of the obtainedcritical burden by the improvement of the general aspect view of the terrains and the capacity of outlier’s detection. The result and the quality of the algorithm demonstrates the improvement in the triangulation mesh, reducing errors in the calculation of over/under burden, free face volumes, cavities and, therefore, in the estimations of clearance/safety distances."

Jan 1, 2017

By Ran Tamir

"This document introduces the use of drone generated aerial photography to collect and analyze fragmentation data for both muck piles and post crusher stockpiles in order to support the continuousimprovement process. In tandem with photo analyses software, drone imaging gives mines and aggregate sites a fast, accurate and economical method of benchmarking and optimizing the process of size reduction to spec."

Jan 1, 2017

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015