Search Documents

By Jennifer Ward

The primary objective of this paper is to establish how a low cost, high definition (HD) camera can allow for easy sustainable recordings of blasting operations. The subsequent analysis of each video can be utilized to monitor what type of performance was achieved and aids in improving blasting performance.

Jan 1, 2015

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By Eric Dussell

Commercial or industrial explosives are mechanically-mixed, fuel-oxidizer composites which exhibit varying degrees of non-ideal behavior. Non-ideality results from a relatively slow and state-insensitive reaction rate (Lee, 1990) and is characterized by C-J pressures, velocities or expansion isentropes significantly lower than those expected from equilibrium, steady-state calculations such as Tiger or BKW (Mader, 1979). This departure results from significant amounts of explosive material which remain unreacted at the sonic point. Energy released by continued combustion within the emergent supersonic region downstream of the sonic point, constrained by local sound speed, cannot flow to the shock front and do work on it. The significant amount of this ‘late energy” and its slow time rate of release must be considered in any blast performance model.

Jan 1, 1997

By R Tom Watts

The blasting industry has changed more in the last five years than in any period to date. The equipment utilized to load boreholes has changed in response to more precise blasting products and programs, and the need to maintain tighter control over product formulations produced by bulk loading equipment. Tread Corporation has built over 1,300 heavy ANFO type bulk loading units currently operating in over 40 countries worldwide. These units have been designed to meet almost every possible loading scenario but there are always new situations that require special designs and configurations to meet the challenge. The focus of this presentation is to make you aware of the process that should be used to determine the equipment best suited for your application. We will discuss loading cycle times, delivery rates, multiple product mixing capability, capacities, manpower utilization, regulatory compliance, and where and when to use automation in the loading process. We will also discuss the suitability of chassis with regard to ground pressure, turning radius, terrain, weather conditions as well as highway suitability. The US Bridge Law as well as laws that cover the concept of axle loading and spacing will be covered. Through new computer aided design and modular design capabilities, you can now have almost any configuration required to meet your bulk loading objectives. We will also review the range of equipment currently available in the market place and discuss tradeoffs between price, capacity, and complexity.

Jan 1, 2000

By Lifeng Li, Jhon Silva-Castro

In a previous work, the authors analyzed the overlapping probability of two adjacent charges in a single hole for pyrotechnic and electronic detonators. This document extends such work to a complete mine blast where more than two holes are detonated. In a mine blast, all the blast holes are connected as a network by detonators to follow a given initiation sequence. Such initiation sequence’s performance is based on the adequate timing between charges in the mine blast. The analysis of the reliability of a mine blast based on the timing between charges and the initiation type is presented in this document. For a long-run time and under proposed operating conditions, the reliability of the mine blast can be analyzed based on the network which is treated as a system. The failure of the system is defined as no success between any two delays charges either in a single hole or in between two holes.

Jan 1, 2016

By James Ludwiczak

We are coming to an end of an era in Midwest surface coal mining. For many years, large tracts of coal lands were readily available for sale or lease to surface mine operators.

Jan 1, 1980

By Steve Collinsworth, Nils Heinke

In 1989, I realized the definite need for change in the Blast Hole Drilling Industry. With over 25 years of experience in dealing with the industry, I am well inGormed and educated concerning the problems that occur in Blast Hole Drilling. After continues interaction with the Drill & Blast Superintendents, Drillers, Purchasing Agents, Mechanics, and others in the field, a basic understanding was developed as to the origins of the main problems that the industry f&s with their drillings programs.

Jan 1, 1997

By C. Feliciano, M. Cavalcante

A large iron ore open pit mine in Brazil operates with reduced blast sizes, due to the imminence of red alerts in the rainy season and the proximity of plant and dam structures that demand control of the maximum load of fired explosives. Blasts are currently not allowed to remain loaded with explosives due to the risk of red alerts, limiting mine operations close to them. There is a need to increase the blast sizes, reducing the number of events required to obtain the planned mass and, consequently, the unproductive operating hours lost with mine evacuations. The WebGen™ wireless electronic initiation system is a technology for firing detonators via lowfrequency magnetic induction that propagates through the medium, without physical connection. A blast was carried out with 406 holes divided into 4 panels, aiming to validate the preloading technique with wireless detonators and its performance in safety and productivity. The absence of lead wires in the system eliminates the risk of interaction between vehicles and detonator cables in stemming and loading operations, which can result in unplanned detonation or misfire. By eliminating the need for a spotter, it reduces people's exposure to dust and the risk of human-machine interaction. Furthermore, it eliminates the risk of unplanned detonation caused by lightning strikes. The pre-loading technique with wireless detonators enables flexibility and efficiency in planning through temporary accesses over loaded areas. In the demonstration, driving over the loaded area was essential to avoid jams and excessive wear on equipment due to the narrow berm and very friable material. Another gain in productivity was optimizing operational stages, since detonators were programmed in parallel with loading, anticipating process stages, in addition to eliminating the need to connect detonators. Considering the average handling and savings in downtime due to the reduction of blasting events, a potential increase in movement of 49,000t (54,013 short tons) in 3 months was estimated, keeping the vibration results within the required limit. The trial with wireless detonators demonstrated the feasibility of carrying out blasts with preloaded panels, without restrictions on the number of panels or detonators, enabling vibration control, innovating mine planning and increasing safety and productivity

Jan 1, 2024

By K. Hausmann, P. A. Sashin, G. J. Prejean

Misfires caused by unreliable shock tube constructions can have significant cost implications and place field workers at serious risk during remediation. Ionomer materials, used as a subtube in shock tube constructions, provide superior hot tack strength, oil resistance, impact resistance at cold temperatures and excellent thermoformability properties. These are important features for resisting blast-throughs and ensuring blasting reliability in demanding environments, such as open pit mining in harsh environments. Superior hot tack strength, strain hardening, and excellent thermoformability properties of the ionomer materials ensure uniform powder distribution along the shock tube during construction and avoid undesired powder accumulation due to deformation or vibration during use. Oil or chemical resistance is another feature of Ionomers. This allows improved property retention in contact with oils and hence longer sleep times of the shock tube. Another feature of these highly engineered ionomers is superior impact strength at low temperatures. This plays an important role considering the resistance to fly rock impact in open pit mining operations in particular in cold climates.

Jan 1, 2011

By Barend Botha, Trevor Davids

The presence of an extensive soft siltstone layer in the middle of the inter-burden sequence of rocks at Syferfontein Colliery in the Republic of South Africa prompted tests to determine the effect of different mid-column decks of inert material in the siltstone layer. The objective was to achieve significant cost savings in explosives use whilst not degrading dragline productivity. An important factor that had to be considered was that the initiation systems available in South Africa are not accurate enough to ensure simultaneous initiation of explosives decks in a blasthole. A number of inert materials were tested including ash, drill cuttings, river sand and crushed stone. It was found that the ash, drill cuttings and river sand did not effectively attenuate the shock wave and that the risks of sympathetic detonation or partial disruption of one or the other explosives deck in a blasthole was high. This became much worse when the inert material was saturated with water. Crushed rock was the most effective in attenuating the shock wave, but this material was very expensive to use because it had to be imported onto the mine.

Jan 1, 2000

By M. Roy

Safety and stability of underground coal mine workings are always in danger when opencast mines are operating in close proximity. A study was conducted to investigate the level of vibration generated from opencast blasting at similar distances on the surface as well as in the nearby operating underground coal mine openings. Eight blasts were performed and nineteen vibration data were recorded on the surface behind the opencast blasting face and also in underground openings at similar distances. It was observed that magnitude of vibration recorded on the surface were more than those recorded in underground.

Jan 1, 2007

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By Virgil J. Stachura, Calvin L. Cumerlato

The Bureau of Mines conducted a series of tests to develop a blasting method that would reduce overbreak and rockfall hazards at a limestone quarry in northeastern Wisconsin. Reductions in overbreak were achieved by shortening the main explosive column and reducing the explosive load in shortened stemming zones in shotholes which were to form the highwalls. Two blasthole diameters, 3 and 4 inches, were used with 7 by 7 foot and 9 by 12 foot burdens and spacings respectively. ANFO, Comsol 300, or PowerAN were used in the body of the shots and Gelmax or 40 pct extra dynamite cartridges were used in the reduced load zones. Smoother highwalls were visually apparent, however further analysis by seismic refraction techniques were performed as an aid to studying overbreak within the rock mass.

Jan 1, 1989

By L D. Santis, L Wardrip

This paper begins with a summary of the development of the sheathed explosive charge from it's conception by the Bureau of Mines in 1981 through the evaluation of its safety, culminating in revisions to the Code of Federal Regulations (CFR), Title 30, Parts 15 and 75 which provide for its approval as a permissible explosive and safe use in underground coal mines. In 1989, Austin Powder Company decided to market a sheathed charge and proceeded to develop a commercial version which they call the Rock*Buster. The Rock*Buster was tested by the Bureau of Mines and subsequently approved as a permissible sheathed explosive unit by the Mine Safety and Health Administration (MSHA). Marketing of the Rock*Buster began in the Spring of 1990. In May 1990, the Rock*Buster was first used in an underground coal mine, Jim Walter Resources' (JWR) No. 4 Mine in Brookwood, AL. Trials with Austin's units were impressive. Representatives from MSHA, the State of Alabama, JWR, the United Mine Workers, and other local mining companies observed the charge break large boulders on the surface. Later, the charges were used underground to break large rocks from a roof fall that were obstructing ventilation. During its first week on the job, the Rock*Buster reduced the downtime experienced on JWR's longwall sections by quickly taking care of problem roof falls which halt operations.

Jan 1, 1991

By Romel Villanueva, Juan Vasquez

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process. For gassed explosives the density varies gradually according to the depth in the hole, due to the pressure on the bubbles by its own weight. The density at the bottom of the hole can reach critical values, which directly affects the start of the detonation in the booster zone with a high probability of nitrous fumes formation. On the other hand, density translates into the amount of explosive and energy available. Therefore, for the optimum performance of the explosive, the minimum and maximum values of the in-hole density must be determined. For the cases studied, the maximum in-hole density and the maximum charge length have been determined. When the charge length is greater than 7.0 m [ 23 ft.] special care must be taken with the cup density, which as a general rule should not exceed the value of 1.15 g/cm3 [71.8 lb/ft3] at the risk of losing the sensitivity at the bottom, also increasing the probability of nitrous fumes, bad fragmentation and finding intact explosive after blasting. In the large holes in Toquepala and Antamina mines, where the charge length can be greater than 9.0 m [29.53 ft]. If the cup density is greater than 1.15 g/cm3 [71.8 lb/ft3] the in-hole density can easily reach a high value of 1.30 g/cm3 [81.16 lb/ft3].

By Tom Short, Paul Kunze

In this paper, the authors describe major changes in drilling and blasting methods instituted at the Zortman And Landusky Mining Company Properties to maintain the viability of these north central Montana surface mines in the present period of depressed precious metal prices. The authors explain how improved drilling procedures minimized problems due to uneven benches and floors. They also describe changes in explosives loading and delay blasting techniques which improved fragmentation, thus increasing metal recovery from heap leaching. Quantities were increased substantially and a new bulk explosives loading system was placed in service with a special down-the-hole bulk loading truck and storage facilities for bulk ANFO and bulk emulsion. At the same time, drill patterns were expanded by nearly 40%. The authors also describe a new technique of using explosives to selectively cast waste and ore in different directions so as to reduce the cost of separating the ore.

Jan 1, 1986

By Enrique Munaretti, Cathy Aimone-Martin, Vitor Rosenhaim, Jair Koppe

Production blasts at one of Copelmi’s coal mine operations will be carried out 100 m (330 ft) from a neighborhood located in the town of Butiá, southern Brazil. Mine management is concerned about the possibility of damages and complaints due to blasting operations at close distances to structures of substandard construction. Blasting in the area is characterized by the use of very low powder factor resulting in confined shots in which movement is restricted to a point of almost undershooting the rock. Over the past year, tests were conducted mainly in the overburden area to determine the best approach to be implemented when blasts move closer to the town. Mine management wants vibration levels to be reduced lower than the damage limits proposed by Brazilian regulations to ensure a safety margin and mitigate perception by the community hoping to reduce the number of complaints.

Jan 1, 2013

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By Manish Uttarwar, Rajendra Yerpude

India is the third largest producer of coal and the fourth largest in terms of coal reserves in the world. However, new research quite ironically projects that despite the continuing growth in domestic coal production, the country’s exploding economic growth will position it to be the biggest coal importer by 2020. India’s inability to meet the domestic coal demand is mainly attributed to low rate of production, increasing stripping ratio, non use of appropriate technology etc. of coal mining operations here. Presently Indian surface mines which have to shoulder the onerous responsibility of augmenting the coal extraction rate at an even brisker pace are mulling bigger, better and more efficient operations ensuring commensurate rise in stripping work as well. This mammoth task can be accomplished only by deploying smart technologies. In this perspective, cast blasting of overburden emerges on the horizon as a promising alternative for enhancement of the production and productivity of Indian open-pit coal mines.

Jan 1, 2009

By John R. Jr Tripi, Paul N. Worsey

Split round blasting is commonly practiced in underground uranium mining in the Big Indian ore belt located in Southeast Utah. The technique is used to prevent ore dilution by separately blasting the ore from the face.

Jan 1, 1985