Search Documents

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By Carl R. Peterson, Robert G. Lundquist

The development of a remotely-controlled drill and blast excavation system is desirable both because it is potentially more economical than mechanical tunneling in hard rock and for safety. A serious impediment to such development is the problem of relocating and reentering previously drilled blast holes to place the explosives.

Jan 1, 1983

By Brian Warner, Siavash Mahvelati, Douglas Rudenko, Mohamad Sharif

Predicting and optimizing production shot vibrations using time-shifting and superposition of signature hole waveforms (seed waves) has been widely used for many years. In this method, a single borehole is detonated and recorded with seismographs at the locations of concern. Since a single hole waveform is a reproducible event, it is reasonable that the seismic signature from a multi-hole production shot can be predicted by summing a series of single hole waveforms that have been time‐lagged at intervals corresponding to delay times from the production shot. However, there are instances where seed waveforms are collected at locations other than the exact location of concern, which raises questions regarding the applicability of such recordings. The present study adopts the well-known concept of dispersion of surface waves to predict seed waves at a location of interest based on seismograms recorded at a closer offset. Surface waves, as their name suggests, are seismic waves that propagate along the Earth's surface. They are the dominant wave type within one wavelength from the ground surface. Surface waves are dispersive in nature meaning that in a layered medium, wave components with different frequencies travel at different velocities causing an input signal to disperse as it propagates. The proposed technique takes seed waves recorded at one location as the input and passes it through a frequency-dependent function developed using site dispersion characteristics. The site’s dispersion characteristics are either measured directly with surface wave methods or retrieved using shear wave velocity information. The output of the function is the seed wave prediction at the farther location of concern. The theoretical background, including the underlying assumptions and limitations, is discussed in detail, and the application of the technique is illustrated through field data from two sites.

Jan 26, 2026

By Duane A. Houkom

Explosive demolition of concrete has been accepted as a safe and economical means of concrete removal for many years. I imagine that the early concrete blasters were experienced rock blasters who applied their knowledge to just another formation. Since a concrete foundation is generally located in a congested area, the owner is willing to accept the higher costs of mechanical removal,rather than promote "a new idea" to his management. This attitude is rapidly changing,making it possible to use the advantages of explosives in more congested locations.

Jan 1, 1982

By Zoltan Susanszky

Technical development in blasting requires improvement of industrial explosion techniques in two fields. One is to apply increasingly exact and economical solutions with more effective explosives, the other is to restrict as much as possible the environmental effect of explosions.

Jan 1, 1978

By Y Nagendra, A. Ravi Kumar

A breakwater is a construction for protecting the marine structures like port, harbor, or anchorage-basin and berthed marine vessels from the destructive influence of the sea waves. The breakwater is constructed by using geologically competent, heavy, massive rock like granite, basalt etc having physical and mechanical properties within the limits specified by the designers. The construction requires boulders in varying sizes ranging from 0.5 kg to 20,000 kg. The stones from 0.5 to 1000 kg are called as core fill and boulders greater than 1000 kg are termed as armor blocks. These armor blocks cover and protect the core fill and prevent it from escaping. The requirement of armor blocks ranges between 25 to 35 %. The rest is core fill. However, the actual requirement depends on the breakwater design. In this context, the task of the mining engineer is to economically produce armor blocks and core from the designated quarry in right proportion with minimal losses. The whole bunch of engineering ingenuities should be put forth for obtaining the required armor blocks. The armor block production from any blast depends chiefly on geological conditions, bench dimensions and blast design. This paper is an attempt to bring out the various parameters affecting the performance of the blasting for armor block production using a case study.

Jan 1, 2005

By GF Brent, Armstrong L. W

It is recognised that presplitting is a special case in blasting which requires the reduction of conventional explosive pressures in order to avoid excessive rock damage. Two routes to achieving this are the use of reduced density explosives or the practice of decoupling the explosive from the blasthole walls. Applications of two such systems in large diameter, deep blastholes are described. Both systems were tested in presplits alongside sections charged with decks of conventional explosives.

Jan 1, 1998

By Zheng Shuangying

The vibration effect of the buried oil pipeline caused by tunneling blasting affects the pipeline safe transportation, tunnel construction schedule and its construction cost. The dynamic response characteristic of the buried pipeline under blast loads is the foundation of designing blasting scheme as well as the prerequisite to pipeline safety. Taking the blasting engineering of Xiannvyan tunnel passing through a buried oil pipeline of the high-speed railway from Xi’an to Chengdu as the background, according to the space relation between tunnel and pipeline as well as the charge structure of V-cut blasthole, the 3D non-linear dynamic finite element model of tunnel-pipeline was established in the light of the equivalent explosive. The vibration response of the ground surface over pipeline resulting from V-cut blasting was simulated by LS-DYNA finite element program. Comparing with the measured vibration velocity waveforms in site, the accuracy and reliability of the numerical model are well verified. On the base of the simulation method, the coupling dynamic response characteristic between buried oil pipelines and soil was further studied and the Von-Mises stress distribution of pipeline wall was obtained. The safety of buried oil pipeline was quantitatively analyzed through the inside stress data of pipeline given by the simulation calculation above. The analytic results show that the maximum vertical vibration velocity of pipeline on the interface between pipeline and soil is 1.62~5.07 times as large as that of soil. When the buried pipeline is located over the tunnel and 13 m (42.6 ft) away from tunnel, the maximum vertical vibration velocity of ground surface caused by V-cut blasting with charge weight 17 kg (28.6 lb) is 3.17cm/s (1.25 in/s) and the vertical peak vibration velocity of pipeline top is about four times as the ground location directly above the pipeline. Meanwhile, the peak dynamic stress of the buried pipeline caused by blasting vibration is only 2.35% of the allowable stress of steel pipeline. The maximum superimposed stress of the blasting dynamic stress and the hoop stress produced by the pipeline internal pressure is 242.56 MPa (35 180.36), which implies that the buried oil pipeline is completely safe under the conditions of the given tunnel blasting scheme.

Jan 1, 2015

By Stanley J. Vitton

An important factor to consider during blast damage investigations is whether the structure was constructed on collapsible soils. Traditionally, these soils have been considered to be soils such as loess deposits, which occur along the Mississippi River in locations such as Vicksburg, MS. However, recent research into collapsible soils has indicated that a number of soils may also fall into this category. A collapsible soil is any soil that is susceptible to large decreases in bulk volume upon saturation.

Jan 1, 1997

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By Marilena Cardu, Mauricio Dompiri, Jacopo Seccatore

Blasting in geological bodies is an industrial process acting in an environment characterized by high uncertainties (natural joints, faults, voids, abrupt structural changes), which are transposed into the process parameters (e.g. energetic transfer to rock mass, hole deviations, misfires, vibrations, fly-rock...). The approach to this problem searching for the “optimum” result can be ineffective. The geological environment is marked out by too many uncertainties, to have an “optimum” suitable to different applications. Researching for “Robustness” in a blast design gives rise to much more efficiency. Robustness is the capability of the system to behave constantly under varying conditions, without leading to unexpected results. Since the geology varies from site to site, and often from bench to bench on each site, setting a robust method can grant better results in varying environments, lowering the costs and increasing benefits and safety.

Jan 1, 2011

By Rodney D. Lamond

The need for blast vibration monitoring can be attributed to a combination of three factors: Structural damage, Blast design and Human annoyance. Traditionally, vibration damage criteria are prescribed in terms of peak particle velocity (PPV), as measured or predicted in the ground surrounding a blast. The PPV in the vicinity of a blasthole is strongly influenced by the quantity of the explosive per delay. In general, the existing prediction models give reliable results but fall short of addressing the change in PPV when the charge is decoupled and/or distributed.

Jan 1, 1995

By Zach Ellis, Dusty Fisher

Lightning is a major concern in the explosives industry. The enormous amount of energy delivered to the Earth from a single bolt of lightning is more than capable of detonating explosives. Although explosives incidents caused by lightning strikes are rare, lightning is of great concern to blasting professionals who spend many hours working on or near loaded blast patterns.

Jan 1, 2015

By Mike Cammack

Western South Dakota is predominately an agricultural area, with exception of the mining and timber industries in the Black Hills region. With precipitation rates averaging below fifteen inches per year, water is a precious commodity to the livestock industry. There is a constant demand for the construction of earthen water storage facilities (dugouts) to catch snow and rain runoff, or developing natural springs.

Jan 1, 1993

By Douglas Bartley, Kevin Hachmeister, Rich Barry

The use of explosive energy as a tool in mining and construction is the most effective way to move large amounts of rock that is otherwise unable to be efficiently excavated. Since the early days of explosive engineering utilizing black powder initiated by cap and fuse to the present day diversity of specialty products and technologies the goal has always been to "Break and Move" as much rock for the least expense possible. It has primarily been the competitive nature of our economy that has driven the advancement of technological innovations and practice. However, the concept of removing rock is not specific to the mining and construction industry. Since the dawn of creation, man has used rock as a medium to express his creativity in the form of sculpture. Even though the process of sculpture requires the removal of rock, the final work is defined by the rock that remains intact. This typically necessitates the extreme care of the sculptor to painstakingly chip away the rock allowing the image to emerge from the original mass of stone. The famous sculptor Michelangelo once said, "I saw an angel in the marble and carved until I set him free."

Jan 1, 2004

By Douglas A. Anderson

It is quite common for people exposed to blast vibrations to ask questions such as "How big was that blast on the Richter Scale?" Although it is tempting to dismiss such questions out of hand, for the lay person it is understandable that something which shakes their house should have some sort of measure attached to it. Since a layman doesn't usually know about particle velocity, frequency or the other terms used in describing and regulating blast vibration, the Richter Scale is usually the only measure they can relate to.

Jan 1, 1994

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By G. R. Adhikari

A major part of mineral production comes from surface mining and there has been a rapid growth in this sector with the deployment of high capacity equipment. The importance of blast design combining appropriately both theoretical methods and practical approach has been well recognized in the field of surface mining. It is known that blast design has a direct consequence on productivity, safety and economic viability of these mines. Blasting is the most common method of breaking rocks in mining, but it has to be cost-effective. In coal production, for instance, drilling and blasting account for 25 percent of the total procution cost. In hard rock mining, the cost of drilling and blasting is about 40 percent. Due to ever increasing concern for cost-effectiveness together with environmental consciousness, designing blasts for each application has now become a stringent requirement and indeed a challenging task as well.

Jan 1, 2002

By Satish Kate

Mining of Iron Ore in India is done by Surface Mining methods and most of the deposits are massive and are occurring in Hills, surrounded by green forest cover. While majority of iron ore produced are from mechanized mining systems, some quantities are also produced from semimechanised mines. In mechanized mines, apart from state-of-the-art level of mechanization, the Run-off-Mine ore is subjected to multi-stage crushing, screening and washing/beneficiation, for improving the grade and ensure segregating of different size range. The steel plants within the country have been operating their own captive mines, where both lumps and fines are used in their furnaces. In case of mines, which exclusively supply ores to export market, the lumps produced yield very high price and thus efforts are being made to maximize lumps recovery. The mine, where the author had been associated, is an export-oriented mine which supplies iron-ore to Japanese steel plants.

Jan 1, 2004

By Claude Cunningham

Simple bulk energy rating of explosives obscures the realities of how these deliver their energy, and diverts attention from the key question of controlling blasting results. Explosive performance is directly related to the pressure pulse impacting on the blasthole wall. This is helpfully visualised by comparing the adiabatic expansion plots for explosives of interest on the right scales and axes. The simple comparison of a pure emulsion with pure ANFO illustrates the practical significance of the intrinsic behaviour of these opposed formulations, showing that the emulsion can be expected to work more by softening rock, while ANFO will tend more to crack it. The explanation for these differences lies in the high shock, low sustained pressure of the former relative to the latter. The technique is readily applied, if a good detonation code is available and able to swap data into a spreadsheet. Any differences between codes will emerge most strongly in comparing the gamma plots.

Jan 1, 2002