Search Documents

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Gavin Yuill, Kameron Ray

"The impact on vibration model accuracy by input data that is inaccurate was previously unknown, butthought to introduce significant error. This paper explores the impact of accuracy of different GPSreceivers, bulk truck density fluctuations, and charge weight location convention on the accuracy of the final vibration model output. GPS accuracy is compared between a professional Differential GPS, a “prosumer” GPS unit and a standard consumer GPS chip commonly found in cell phones. Bulk truck density fluctuations are compared from the density given by the operator and the actual cup density measured in the field. Charge weight locations explored are from the bottom of the blast hole, center of the powder column, and collar of the hole. The findings show that the weakest link in vibration model creation is actually low seismograph accuracy standards. Errors introduced from such are generally greater than those introduced from other sources."

Jan 1, 2017

By P D. Kasbanis, Lyall Workman

"The energy output of an explosive is typically calculated using an equation of state and computerapplications. Results are reported as weight and bulk strength, either in absolute terms or relative toANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of “available energy” associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated."

Jan 1, 1996

By Selamawit Asfaw, Mohamad Sharif

In recent years, the use of modal analysis has increased to include many different aspects of the construction industry. Computer modal analysis can be used in determining the dynamic properties of a structure by mathematical equations and knowledge of the structure’s physical properties. This technique can now be used to predict the level of vibration induced by blasting on adjacent structures. Ground vibration induced by buried explosives is a major concern for contractors when excavating near utility pipelines such as gas and water lines. The size limitations placed on easements causes the necessity of additional utility lines to be placed in close proximity to existing lines. Through the development of computer models of the pipe, stress analysis can be performed prior to blasting. Based on the calculated dynamic properties (natural frequencies and modal shapes) and the maximum allowable displacements and stress levels (which are established by the pipe manufacturer) the allowable maximum charge weight per delay can be selected for the blast. The selected maximum charge weight per delay will ensure that the resulting pipe peak particle velocity level is within 95% confidence. This means, statistically, there exists a 95% probability that the actual pipe peak particle velocity would be less than the predicted value. The pipe is then instrumented with vibration measuring sensors to ensure that vibration levels are within the allowable maximum pipe strength. In conclusion, this technique can assist the engineers and blasters, to establish the proper blast design. It allows for safe and efficient installation of additional utility lines adjacent to existing lines. This technique can also be applied to predict the structural response to blasting induced vibration for a variety of complex structures. A detailed explanation of this technique, as well as an example of application including formulas used for this technique will be provided in this paper.

Jan 1, 2000

By Scott King, Norm Patterson, Ruilin Yang

The multiple blasthole fragmentation (MBF) model developed by Orica models the contributions from multiple blastholes to fragmentation at any given point in the rock and simulates a production blast with the actual geometry of the blasted overburden and free faces, explosive loading, multiple decking, and delay timing of each explosive charge. The model has been successfully applied to several open pit mines and quarries around the world, including Canada and the United States. The peak particle velocity (PPV) induced in the rock from the explosive detonation is used in the MBF model as the key parameter relating to the size distribution of the rock fragmentation. Relating the PPV to the rock fragmentation is based on earlier work relating the particle velocity to the dynamic strain in rock. A recent publication further revealed that the PPV is related to the maximum relative displacement that induces three dimensional strain at a point in the rock. The model can explicitly model most of the blast design parameters including explosive properties.

Jan 1, 2018

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By Mattos J. L. C

Drilling and blasting with explosives in mining operations near communities require careful planning to mitigate socio-environmental impacts. Ground vibration, noise emission, flyrock, and dust dispersion are factors that may trigger conflicts with local populations. However, large-scale operations demand high productivity and intense material handling, making it essential to balance operational performance with impact control. The adoption of best practices, combined with advanced monitoring and mitigation technologies, enables sustainable mining even in proximity to inhabited areas. This study proposes the use of double and triple-deck blasting techniques with large-diameter boreholes (12 ¼” – 311 mm), addressing the sizing of charges and decks, as well as measures aimed at reducing noise perceived by nearby communities. The approach seeks to maintain the use of large drilling rigs already present in the operation, avoiding costs related to premature equipment replacement or expensive alternatives, while minimizing environmental and social impacts and promoting a more balanced and responsible mining model.

Jan 26, 2026

By Oliver Finn

Gold dredging has made such rapid strides of late and there is such a widespread interest in this branch of mining that I venture to contribute a detailed account of the way in which a Keystone driller was used by me in California to loosen, by blasting, a very tight gravel deposit, preparatory to dredging. There is a great difference between “cemented gravel” and “tight gravel.” A truly cemented gravel is not a dredging proposition, while the tightest possible gravel, where there is no cement, can be made easy working by the following method of blasting:

Jan 1, 2008

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By Harry: Lobb Verakis

Mining operations have made tremendous strides in improving the safety of blasting as shown by the significant and continual decrease in fatalities and serious injuries. Advances in blasting technology and blasting practices have played a significant role in reducing fatalities and injuries. However, even with the decline of fatalities and injuries blast area security continues to be by far the leading factor in blasting accidents. Even though there continues to be an increase in the use of industrial explosives and blasting agents in the U.S.A., the decline in fatalities and injuries from blasting accidents has persisted.

Jan 1, 2010

By LaRay Collyer

San Juan Mine began pre-splitting the highwall prior to cast blasting in August 1986. The first pre-split shot used six inch PVC (polyvinylcloride) pipe inside a 10 5/8 inch hole, drilled at a 74 degree angle. The powder factor was about .90 pounds per cubic yard.

Jan 1, 1990

By S. Gajardo, E. Valdés Guerra

Together with Sociedad Punta del Cobre S.A. (Pucobre) and Orica, we are carrying out a study of alternatives for methodology of excavation in Slot Up Raises from actually built with Blind Hole (BH) to drilling and blasting (DB) methodology. The study is part of the permanent search for innovation, the use of technology and the reduction of mine operation costs. This application aims to optimize the Sub Level Stoping method, which has historically been exploited at Pucobre. Using a new variant of the method “Open Stoping”, through the initial development of ascending blind raises using a pilot drilling of a bore hole, with the objective of eliminating the upper level in order to excavate the free face opening. This industrial test aims to replace the mechanized BH Up Raise of 1.5m (4.9 ft.) in diameter and 30m (98.4 ft.) high, with a Up Slot Raise considering two separate blasting events, using different technological enablers, as detailed below: accuracy drilling with relief holes of 254mm (10 in.) diameter, high viscosity bulk emulsion, wireless initiation system and high-strength injectable bulk resin. Considering the importance of the success of this application, a DB diagram was defined to allow the opening of the up raise in two blasting events, separated by intermediate stemming deck located at the same level at a height of 15m (49.2 ft.) from the collar, using high-strength injectable resin. The first blasting event considers the first section from the collar to the first 15m (49.2 ft.), using wired electronic initiation that is detonated on the first day. A second event blasts the section from 16.5 to 30m (54.1 to 98.4 ft.), using a wireless initiation system, as, it has no physical connection, is blasted on the second day after the extraction of the material resulting from the first event. For greater precision, the design of the explosive charge configuration and initiation sequence is made, adjusted to the measurements of trajectory deviations of the actual ground drilling and is also considered for the control of the explosive charge configuration with high viscosity bulk emulsion. This application improves the profitability of the mining business by generating savings through the change of Blind Hole methodology, estimating a savings of more than 75% per Up Slot Raise

Jan 1, 2024

By John Platt, Mark Stephens

"When blasting is required in critical areas and anticipated shot movement and quick cleanup areessential to the success of the project it is extremely important to use the best technology available to achieve the goals expected by the customer. Wampum Hardware was given such a challenge in 2014-2015 when the PA Turnpike and New Enterprise Stone and Lime hired the company to do presplit blasting along the PA Turnpike. The face height averaged 45 feet (13.72m) and the shots had to be controlled to stop within 60-75 feet (18.29-22.86m) of the face or in this situation before they entered the travel lanes on the PA turnpike. In many if not most blasting environments, it is essential in controlling the movement of a blast, to make certain that the face holes are drilled at exactly the right place, with the proper amount and type of burden in front of and to the sides of the borehole. Profiling is an important first step to insure that the holes are drilled at exactly the right place and showing us the correct amount of burden in front of each and every drill hole."

Jan 1, 2016

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By O. Rielo, P. Katsabanis

Traditionally fine aluminum is not used in dry commercial explosives due to the hazard associated with aluminum dust explosions during mixing. An industrial process has been developed which enables the safe use of paint grade Aluminum with ANFO. The addition of fine aluminum particles resulted in increased velocity of detonation of ANFO compositions. Velocities of detonation, in 52mm (2 1/16 in.) diameter confined charges were 20% higher than velocities of detonation of straight ANFO. The detonation performance of fine grained ANFO was not benefited by Al at the diameter tested. Furthermore use of larger Al flakes resulted in decreased velocities of detonation. The results are compatible with the experience of Al addition to high explosives. Tests were also conducted using bio-diesel, finding no substantial difference in the performance of AN fuel explosive compositions which used bio-diesel.

Jan 1, 2009

By Felix Degold, Mark Ganster

Achieving a customer optimized fragmentation by using robust data from new technologies e.g. GPS positions of boreholes, fragmentation analysis to calibrate the geology and fragmentation prediction models. The inclusion of the collected data into the blast’s design makes it possible to accomplish a desired particle size distribution.

Feb 1, 2020

By Benjamin Cebrián, María Gil, David Flores

In many occasions during the Mining operation life, blasting engineers find different and controversial results of fragmentation, dilution or wall control for the same geotechnical domain and blast design (pattern and explosive charge). Most of the times, the difference between same blast designs is not measured, not controlled. Once a blast designed is defined, the most important part of the process after that is the implementation of every step of the blast on site. Almost nobody is measuring it, controlling it, but just controlling implementation is possible to relate blast design with results in a consistent way, to optimize the full process of D&B. Controlling implementation not only per event but also to check and change trends and decision-making is paramount for optimization and saving millions of extra costs every year. The lack of resources and the hardness to manage all the info created every day in a blast make this process very tough and difficult to maintain in long term. The use of new technologies on site and software that allows a best, more consistent and continuous control of blast implementation have been proved to be the key for optimizations and cost saving. This document shows the evolution of drilling and blast digitization process, savings and trends in a mine, using new technologies that creates business opportunities and general improvement of D&B process.

By F. Schott, M. James, G. May, E. Baker, C. Johnson, R. Bauer

Explosive demolition typically utilizes cutting charges to sever columns, detonating cord to time charges and provide an initiation path, and dynamite as a kicker charge. The kicker charges of dynamite are used to “move” columns out of alignment, causing collapse. Demolition projects involving dynamite can pose significant health and safety risks to workers and the public. Nitroglycerin in dynamite can cause dizziness, fainting, and other health problems. Moreover, dynamite placed directly on columns can result in fragmentation and cutoffs, preventing other charges from being initiated and resulting in incomplete demolition. Fragmentation can occur from columns and travel significant distances from the initiation point, sometimes reaching hundreds of meters away. This fragmentation can pose serious dangers to anyone in the vicinity, including workers and members of the public, as the debris can cause severe injuries and property damage. The force and velocity of the fragmented material can be unpredictable and difficult to control, making it important to take proper safety precautions and consider alternative demolition methods that minimize the risk of fragmentation. Previous work concluded that casing charges in water showed that a reduced dynamite charge mass could still successfully kick the charge out of alignment. This study aims to investigate the use of Pentolite boosters in water-cased charges as a safer alternative to dynamite-based demolition. The research involved testing various amounts of dynamite and pentolite boosters in water to compare their effectiveness in moving a hanging W-beam, which swung freely like a ballistic pendulum. Water-cased charges consistently move the column at a higher velocity than the traditional dynamite charge placed directly on the column. The method of water-casing increased the area of impact and impulse felt by the column, improving demolition efficiency when compared to traditional demolition methods as found in previous studies. Pentolite water-cased charges moved the column at 7.8 meters/second (m/s) while the dynamite water charge moved the column at 5.9 m/s. The increased strength and explosive properties of the pentolite contributed to this increase in velocity. This study showed that it is feasible to remove dynamite from demolition projects by utilizing pentolite boosters and that when considering safety, explosive properties, and effectiveness, pentolite boosters can be cost effective as well.

Jan 1, 2024

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000