Search Documents

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By J. Pizarro

Any organization that subjects its activities to a continuous improvement methodology, aiming to optimize their processes and services, must be able to adequately measure the results of the implemented changes to pursue better outcomes. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators. Over time, many tools were developed for us to obtain PSD data, albeit each of them had their own shortcomings. The first ones to be developed involved photographing the muck pile including a scale object, uploading those photos to a PC, and using specialized software to analyze each one. As a result, analysts would get a PSD curve that served as reference for the performance of the blast. This method, which is still used, has major shortcomings. The most obvious one is that it is only able to capture a slice of the blast, which corresponds to the exposed section of the muck pile the analyst has access to, and even there its reach is limited to the areas that are safe for getting close enough for placing the scale, which are not many. Consequently, this is a very limited way to get a fragmentation performance assess for a blast. Currently, autonomous systems are capable of taking continuous pictures of the muck pile. Installed on a shovel, conveyor belt or crusher feed, these systems can take a continuous stream of pictures that are later analyzed automatically without the need of human intervention. These systems greatly increase the volume of data and, consequently, we have a PSD curve that is more representative of the blast performance. However, this technology still had issues when trying to sample front end loaders mining operations or getting results from underground blasting due to the inherent difficulties of these operations. New algorithms used for capturing and processing data for front end loaders can overcome the harsh environment of their operations and produce PSD data in high vibration environments and difficult mining angles. For underground mining, algorithms can be used to sample each truck exiting the mine, giving a reliable source of fragmentation analysis that can be traced back to their stope of origin. The development of this technology extends the existing system’s capabilities and helps us in our efforts to improve fragmentation results with each blast.

Jan 1, 2024

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By Peter Moser, Frank Chiapetta, Sacha Diaj, Florian Bauer

Good toe breakage and a flat working bench after blasting are important parameters to achieve a high productivity during material loading and reduce the necessity for secondary blasting. Good toe breakage requires a proper burden – side spacing design and a suitable sub-drilling. With unfavourable jointed rock mass conditions the use of horizontal bottom holes still can be found as common work practice even that this is associated to high risks.

Jan 1, 2009

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lime Companys new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By Carl E. Jones

This presentation discusses the properties of the two-component explosive, KinePak, and how it is used by the utility industry.

Jan 1, 1978

By Dr. Paul Worsey, Dr. Calvin Konya, Dr. Anthony Konya

Development of methods to calculate presplit blasthole pressures through simplified models, namely the Empirical Model and the Detonation Pressure Model. These models can be used with variations in explosive type and diameter, along with borehole diameter. All models have been validated with test data and shown to have minimal error.

Feb 1, 2020

By W C. Brukle

Our title for this presentation could be taken in many ways. One course would be terrifying and that would be to cite incredibly bad practices. All of our votes/efforts should be for the reverse direction in which everyone does his/her best to keep their pit or working place free from hazards.

Jan 1, 1983

By Visitor Makiyi, Chris Batten

Poor coal recovery due to coal damage or loss caused by blasting can have a significant impact on a mining operation. Increasing coal recovery by reducing blast damage can provide a significant opportunity for coal mines to maximise their revenue and reduce their operating costs. This paper provides details on advanced drilling and blasting techniques used throughout the coal industry globally to prevent coal damage and movement during blasting. Typical coal loss and damage mechanisms are explained, along with how each of the applied techniques works to minimise the impact of each mechanism. Key requirements for a coal loss reduction program are detailed with typical design parameters used for each of the methods discussed. The positives and negatives of each method are also provided to enable comparisons and help determine suitability for a particular coal mining operation.

Jan 21, 2025

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By Robert Hopler

RBH Note: At the time of this price list the handwriting was already on the wall regarding the ultimate breakup of the company under the Sherman Anti-Trust Act. The brand names Atlas and Hercules, noted on page 3 of this pricelist, would become the names of the new companies created from du Pont.

Jan 1, 2012

By E. Vilaescusa, J. Eloranta

The work presented in this paper investigates the influence of non-ideal detonation characteristics related to the blasthole diameter, base emulsion sensitivity (micro-balloon sensitised versus unsensitised) and percent emulsion on the explosive shock energy available to break rock using ANFOemulsion blends. A series of theoretical equal powder factor bench blasting patterns with hole diameters of 127mm (5”), 140mm (5.5”), 152mm (6”) and 165mm (6.5”) are compared to assess the non-ideal confined shock-state work energies. The Non-Ideal Shock Energy Factor (NSEF), which is the available shock energy per cubic meter of blasted material (MJ/m3) or kilocalories per cubic yard (kcal/yd3), is used to compare the different blasting patterns charged with a range of ANFO-emulsion blends from zero to 50% emulsion.

Jan 1, 2012

By C. Aimone-Martin, C. Dowding, M. Jern, J. Gjødvad

This article compares percentages of compliance for six national standards to demonstrate how these standards vary on-site in a real project. This, to the best of the authors' knowledge, has not been accomplished before. Different standards not only vary in allowable amplitudes of induced vibrations but also in how they are measured (transducer location, transducer orientation, frequency content of vibration, etc.). Thus it is not straightforward to compare the permissible values of induced vibrations with each other. This challenge of comparison is overcome in this project by instrumenting a structure with multiple transducers according to different national standards and comparing the degrees of compliance. Compared herein are compliance with standards used in United States of America, Germany, Great Britain, France, Austria, and Sweden. Averages of the percentage of compliance and ratios of measured vibration amplitudes for all six national standards are compared both in tabular and graphical form for 20 blasts at the Aitik mine northern Sweden. It is the largest open pit mine in Europe and blasts are atypically large with more than 1000 kg charge per hole and several hundred holes per blast, lasting 3-5 seconds. Results show that percentages of compliance can vary by as much as 2 to 75 % for these blasts at this structure. The overall project is a cooperative effort between EFEE (European Federation of Explosives Engineers) and ISEE (International Society of Explosives Engineers), supported by more than 17 persons from 8 different countries. At the present the experts are the four authors of the present paper and Dr. Robert Farenfield, Dr. Nathan Rouse, Douglas Rudenko, Brent Meins, Kenneth K. Eltschlager, Karin NorénCosgriff, Travis A. Davidsavor, Vitor Luconi Rosenhaim, Johannes Kutschera, Bernard Thierry, Thomas Moser, Cory Loukedis, and Keith Best. The project began with a literature study and a survey including an evaluation of the answers provided by members of EFEE. Results were presented at the ISEE conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019 (Gjødvad & Jern, 2019; 2020). The second part of the project was initiated in May 2021 with installation of 7 seismographs from two different manufactures, 3 cracs gauges and 2 microphones on a building at the Aitik mine in northern Sweden. The third part of the project has moved to the United States. Two residential structures adjacent to quarries are being monitored in Michigan and Ohio. Installation and monitoring began in March 2023 and are expected to continue for 6 to 12 months. In addition to the objectives of phase two the 2023 study includes calculations of global wall strains from measured velocity time histories and measurement of response of existing cracks to vibratory and climatological effects

Jan 1, 2024

By J E. (Boet) Coetzee

SAFEX International, as the name suggests, is a global organisation, which has the fundamental objective of improving the safety of operations concerned with the manufacture, storage, transport, and use of commercial and military explosives and pyrotechnic products throughout the world. It is a nonprofit making organisation of manufacturers of explosives from all parts of the world, founded in 1954 with the aim of exchanging experiences within the explosives industry. Every third year SAFEX organises a Congress during which members present papers on selected themes and discuss reports of significant incidents that occurred since the previous Congress. Admission is for SAFEX members only, thereby creating a safe environment for discussing problems “within the family”. The XV Congress will celebrate the Association’s 50th anniversary in Geneva where it was founded. An overview of the Congress indicates its structure and covers aspects such as the training event, technical seminars and the themes for the plenary sessions and associated workshops. The paper also highlights the special event for the chief executives of member companies and the review of incidents that occurred in the industry since the last Congress. The Congress concludes with a social programme for delegates and their partners on the last day.

Jan 1, 2005

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By James R. Kennedy

The recent drop in world gold prices is driving many northern Nevada underground gold mines to look for new ways to improve and enhance current mining operations. Continuous improvement programs at these mines are finding the means to increase mine productivity while reducing total production cost. This paper looks at developments in the drill and blast program at Independence Mining Company’s Murray mine.

Jan 1, 1999

By Kia Riihioja, Mike Higgins

A major difference between electronic and pyrotechnic detonators is that, in almost all but the simplest of blast layouts, computer software is required to plan a blast using electronic detonators. While it may be possible to program delay times without software, using only the manufacturer’s control hardware, the full potential of electronic detonators can only be realized through software. Until recently, the only software available has been provided by the suppliers of the electronic detonators. These usually have just enough features to create a hole layout and to assign times to the detonators in the holes. The software is also able to communicate only with the manufacturer’s detonators. This means that the client may be compelled to change several parts of the blasting process when a different delay system is adopted, from design through to implementation and reporting, even though these may be sub-optimal at the client’s mine. While many authors have demonstrated improvements in blasting outcomes using electronic detonators, very few have discussed how the delay times were calculated. Where the calculations are discussed, it is also obvious that the delay times must be monitored and re-evaluated as conditions in the mine change. For example, the principles of superposition and scaled distance, burden relief and energy cooperation between holes should be checked constantly for different locations within the mine, changes in rock properties, or even for differences between design and actual hole positions. The most common methods in blast design software to calculate delay times are inter-hole interval, relief contour and direct editing. Although they are simple in concept, they can result in fundamental errors if they are not applied correctly. The software for electronic blast designs should be capable of not just a timing calculation, but also of showing, to some degree, the impact and interaction of the calculated times.

Jan 1, 2004

By Italo Onederra, Gary Cavanough, Ewan Sellers

Reactivity of ammonium nitrate based explosives is associated with the presence of iron sulfides in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. The stability of explosive products can also be linked to in-hole density, which influences detonation efficiency, breakage performance and the potential generation of Nitrogen Oxide (NOx) fumes. Reactive ground testing involves detecting a temperature rise of a mixture of a bulk explosive product sample, a ground rock sample and some specific chemical agents. This paper describes improvements in reactive ground testing involving the use of time lapse video analysis and detection of NOX gas emissions from the sample. Reactivity is stored and linked to a using cloud based software to map of the mine showing the exact location of the sample. The location marker can be selected to allow quick access to the sample test results and video. In addition to reactivity, the stability and detonation performance of bulk product can also be influenced by depth. In this paper, a system that simulates product at depth and measures density changes and monitors the structure of bulk samples is described. Results from an explosive product are analyzed and detonation performance is assessed by the measurement of velocity of detonation and detonation pressure.

Jan 1, 2018