Search Documents

By A Gene Riggs

The Cerrejon Coal Project in Colombia, South America is one of the largest coal mines in the world. The mine is located in northeastern Colombia on the La Guajira penninsula. The area is in a remote valley 132 miles east of the city of Barranquilla.

Jan 1, 1984

By Douglas Bartley, Robert McClure

This paper discusses the advances in programmable, testable high accuracy electronic detonator technology. The operation and safety of electronic detonator systems are required to meet rigid safety standards and withstand the demanding environment of in-field applications. These requirements are discussed through comments on existing safety requirements in Europe.

Jan 1, 2000

By B R. Spencer

Using bulk repumpable water gel explosives in underwater shooting results in even more benefits to the user than a "dryland" customer. It is nearly impossible to reshoot underwater, so a bad shot causes tremendous problems. The huge expense of operating drill boats, dredging buckets and clamshells makes shot loading, hookup and digging cycle times critically important.

Jan 1, 1990

By Choon Sunwoo, Chang-Ha Ryu

There are various methods available for the recovery of dimensional stone in open pit quarries. Explosive blasting has more advantages in the economic point of view over the other methods but was not widely used in Korea because owner was concerned about much economic loss when it failed. Several years of efforts have been made in order to develop more effective cutting methods and to spread to the quarries for strengthening the competitiveness in the market. Rock cutting by jet flame and black powder was generally used in the early stage. Black powder was applied to cut the last horizontal plane after forming other vertical planes using the jet flame. Jet flame operation, however, is time consuming and produces excessive noise, and as the result, brings adverse effects on the operator as well as the complaints from the residence adjacent to the quarry. Some mechanical methods such as the slot drill, diamond wire saw or in-situ scale of diamond saw cutting were introduced. Most effective cutting methods using the explosive blasting were developed and applied successfully. Black powder was replaced with the detonating cord. A new air decking technique where plug was not used was developed. This paper reviews the technology for dimensional stone cutting and case study in Korea.

Jan 1, 2003

By Trevor Garbutt, Peter Bellairs, Jason Sander, Glenn Shaw

The Yarrie Iron Ore mine is located in the Pilbara region of Western Australia some 200km eastsoutheast of Port Hedland, the closest large regional centre. The mine is owned by BHPIO who has contracted a large Australian mining contractor Roche Bros to be responsible for the total mining, crushing and trainloading functions. This paper describes a drill and blast optimisation program, resulting from the introduction of a new emulsion matrix called Titan@ Red used to manufacture both HANFO and pumped emulsion ANFO blends.

Jan 1, 1999

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By Richard Arsenault

The production of oil & gas from wells requires method of flow from the producing formation into the well bore. Once the well is drilled it will have casing pipe installed to protect the integrity of the well formations and means of delivery to the surface. Once casing pipe is installed it will be cemented in by pumping cement through the annulus of the casing pipe down to the bottom of the well and allowed to flow outside the casing pipe up into the formation.

Jan 1, 2007

By Yong Pan, Purushotham Tukkaraja

Block caving is a preferred underground mining technique due to its high production rate and low operation cost. Before its final step into a mature caving system using gravity to break rock, drilling and blasting are required to form drawbells to connect the production level and undercut level and induce the initial caving propagation in undercut level. A large amount of toxic fume generated by blasting activities poses a big threat to people working in a confined environment and ventilation is assumed to be the most economical and efficient way to deal with this issue. Past research shows that it’s common to use traditional methods like using a formula or using numerical method (Computational Fluid Dynamic (CFD)) simulation to predict re-entry time after each blasting, but it fails to consider the percentage of toxic fume entrapped in muckpile, which could reach up to 70%. In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

By Ray Heater, Qian Liu, Alan Bauer

The channel effect is a phenomenon that takes place with decoupling explosive charges; an air shock wave propagating ahead of the detonation wave in the annular space around the explosive charge compresses the charge so that the process of detonation is modified and even stopped. For commercial explosives, such as AN/FO slurries and emulsions, the channel effect causes partial detonation under certain conditions. To simulate and evaluate the phenomenon, a hydrodynamic model was developed based on the assumption that the pre-shock wave is produced by Mach reflection at the tube walls. Based on instrumented experimental studies with the above explosives in diameters ranging from 25 to 90 mm in pipe sizes ranging from 35 to 127 mm, it has been possible to demonstrate that a criterion for failure based on a critical impulse concept fits the experimental data well. Critical impulse values for the various explosives tested are presented along with the necessary correlations between charge and borehole diameter required to produce this.

Jan 1, 1988

By James Keenan

Mesabi Range blasting has evolved in over a century of mining. The obstacles including: hard and heavily jointed rock, bitter winters and frequent wet holes; combine to create a unique challenge for blasters. This paper documents current pattern designs, powder selection and loading practices for these seven mines that consumes as much as 130 million lbs of explosives each year. Blasting is characterized by wide burdens and spacings, large diameter holes (up to 16-inch) and bulk loading of augered and pumped emulsion/prill products.

Jan 1, 1996

By J J. Mullay, G W. Anderson, C J. McFinley, J F. VanNorman, C J. Kefer

Previous work has shown that testing of precompression effects conducted on a small scale under simulated field conditions in actual rock provides a reasonable model for the evaluation of explosives and initiators under the adverse conditions encountered in production blasting. Using this methodology can result in greater understanding of the phenomena as well as the ability to predict performance. This effort has been extended to evaluate various parameters not previously studied in a controlled fashion. The present paper describes the use of this technique to study the effects of delay timing on precompression effects. Intervals from 25 to 150 milliseconds are included in the study. Both VOD measurements and damage estimates are utilized in the evaluation. The results demonstrate that timing delay between holes is quite important in determining the overall effectiveness of a blasting program.

Jan 1, 1994

By Ola Lindahl, Mark Irving, John Hutchings

"Blasting is a process starting with a geometric description of the block of rock and ending with a pileof fragmented material. A key step in improving the productivity and quality control over the processis the integration of blast planning software, explosive delivery control systems, and blast recordingwithin one seamless customer solution."

Jan 1, 1997

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

By Robert Hopler

In accordance with the 57th section of the Explosives Act, 1875, the following report on the working of the Act during the year ending December 31, 1903, is submitted. There have been no modifications of the law during the year. No complaint is made of any falling off in the general condition of factories and magazines, and in one instance only during the year have legal proceedings been taken for any irregularity. The occupiers of factories and magazines have invariably shown perfect readiness to remedy any defects, and the managers have themselves in many instances introduced improvements tending towards greater safety. The number of deaths (5) from accidents by fire or explosion in the manufacture of explosives is below the average for the decade (6•4). Looking to the large number of persons employed in this trade, the number of deaths is not excessive and will compare favorably with the death-rate in other dangerous trades. Notwithstanding the large increase in the manufacture of explosives, the average number of deaths has greatly decreased since the passing of the Explosives Act, whereas the number of fatal accidents with explosives under conditions to which the Act does not apply appears to increase with the extension of trade.

Jan 1, 2006

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.

By Terra Dinamica, Frank Lucca

This paper discusses blast design for vibration control in tight construction blasting. Topics include blast pattern geometry, blast design formulas, loading, explosives & initiation selection, and utilizing borehole deviation equipment and lasers, and rules of thumb. The paper will also explore vibration prediction, neighbor relations, and related topics, such as blast plan submittal. Various projects from metropolitan construction blasting operations will be used as examples. Examples include blasting in the inner city, next to pipelines, and in housing developments.

Jan 1, 2005

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines has developed computer software to study the effects of initiator scatter on all aspects of the blasting process. The software is useful because it is difficult to obtain actual initiator data, particularly the standard deviation which is needed to express initiator scatter. The new software is structured to allow blasters to answer the question: how precise must initiators be to insure a successful blast? Successful is defined statistically in terms of a confidence level. The software can be used with any possible design since there are no restrictions due to size or complexity.

Jan 1, 1992

By Sayantan Chakraborty, Kaushik Dey, SaKaushik Dey tyabrata Behera

Drilling and blasting is a popular excavation technique in the drift of underground mine. Faster completion of drift reduces the gestation period and thus longer blast pulls are attempted with longer drill holes. This compels the blasters to initiate higher charge quantity with higher confinements and ultimately results into blast-induced cracks beyond the desired periphery line of excavation. Assessment of the extent of these crack networks is difficult and often neglected. Near-field ground vibration models are often used as damage predictors (Dey, 2007, Yang et.al 1993, Holmberg et. Al 1979) but not necessarily deals with the positions of the cracks. Qualitative measurement of actual damage extent often measured using some geophysical tools, namely, P-wave velocity (Tezuka, 1995), seismic imaging (Dey, 2011), bore hole pressure monitoring (Brent and Smith, 1996), electrical resistivity (Grady and Kipp, 1993), GPR (Adams et.al, 1993) etc. Ground Penetrating Radar (GPR) is a similar geo-physical tool, which uses Electro-magnetic (EM) pulse for characterizing the medium. Similar to other geo-physical tools, GPR also comprises of a transmitter and one/multiple receivers to generate the EM pulse and receive the same after reflection/refraction from the medium(s) respectively. After its development in 1970s, GPR gained increased popularity due to its application in many important fields, namely, identification of buried objects, geological characterization, identification of geological disturbances etc. Thus, it is felt that GPR technique can be used to detect the invisible cracks inside the rockmass from the rock surface (wall and roof) itself. Understanding the same, field experimentations are carried out in an underground manganese mine in Central India, which operates on the ‘cut and fill’ method of mining at a depth of around 300m from the surface. Wedge cut blasting is carried out in the horizontal drifts of the mine using suitable blast design. A 1.6 GHz antenna was used for the GPR scanning, in which GPR transmitter transmits signals predominantly of the said frequencies. The signals get reflected back from any type of interfaces between materials in the target area, with different dielectric properties and is received by the receiver part of the ‘trans-receiver’ antenna and memorized in the Data Acquisition Unit (DAU). The data acquired is processed using a software. Ground vibration monitoring of the blasts are also carried out to develop a vibration predictor. The numerical analysis of near-field vibration predictor model results into the estimated vibration levels at the point of identified cracks. Introduction

Jan 1, 2019

By R W. Bellenie, P N. Blakey

The phenomena of post detonation gases in muckpiles is reasonably well known. It causes the 'rumbling' noises occasionally heard after a blast in open pits or quarries and is thought to occur due to initiation of carbon monoxide, hydrogen, etc. by 'hot' spots within the muckpile. The problem usually occurs with highly aluminized products, but can occur with any oxygen deficient product. This phenomenon was never a problem underground due to restriction on access to blast areas, ventilation criteria, etc. until the advent of large diameter blastholes and particularly their use for specialized applications such as drilling for blasting down 'hang-ups' in ore passes.

Jan 1, 1980