Search Documents

By C. W. Smith

The Bureau of Mines conducted physical and chemical beneficiation studies on three samples of waste investment casting molds to devise a method to liberate and recover zircon. Rod mill grinding, autogenous attrition grinding, and caustic leaching were liberation methods inves-tigated. Flotation, gravity separation, and caustic leaching and sizing were recovery methods investigated. Flotation techniques produced con-centrates containing up to 74.2 pct zircon with a zircon recovery of 53.4 pct. Gravity concentration produced concentrates containing up to 98.6 pct zircon; however, recovery of the zircon was only 57 pct. Caustic leaching and sizing produced concentrates containing up to 98 pct zircon with attendant recoveries of 81 pct.

Jan 1, 1985

By J. M. Riley

This report summarizes Bureau of Mines experiments in purifying sulfate leach liquors, which were prepared from low-tenor beryl concentrates by modifying the Degussa process. The leach liquor was prepared from a beryl concentrate containing 2.7 percent BeO by (1) sintering the beryl concentrate with limestone in a rotary kiln at about 1,150° C. and by (2) treating the sinter first with sulfuric acid and then with water to form and extract beryllium sulfate. About 80 percent of the beryllium was dissolved. The resulting leach liquor contained 2.4 grams of BeO, 20 grams of Al203, and 6 grams of Fe203 per liter. The laboratory solution contained much more aluminum and iron than a solution derived from treating 10 percent BeO concentrate, which is the standard raw material used by industry. Tests were made to determine the behavior of the solution toward alum purification and limestone neutralization both of which were employed industrially in conventional Degussa procedure.

Jan 1, 1962

By Robert L. Jones

The Boston Consolidated mine is situated in the Bingham mining district, Salt Lake County; Utah (fig. 1). The property has had a noteworthy production of cupriferous, gold-bearing, pyritic ore in addition to lead ore. The Bureau of Mines established a diamond-drilling development project on the property in September 1943 with the primary objective of determining the continuity of a mineralized zone in the Commercial limestone below and to the northeast of the 800-foot level (fig.2). Examination of the geologic feature at the property previous to drilling indicated that the mineralized limestone horizon would continue belay the 800-foot level, but with a flatter dip than disclosed above this level. During the project period, 36 holes totaling 4,001 feet were drilled from underground stations outlining the zone below the 800-foot level (figs. 2 and 3).

Jan 1, 1949

By S. W. Zoldok

[The Bull Valley iron-ore district lie,; in the northern part of Washington County, Utah, approximately 30 airline miles southwest of the highly productive Iron Springs area (fig. 1). Iron-ore occurrences in the district have been known for many years, but they have not been mined, largely because of the inaccessibility of the area. The Bureau of Mines established a development project in the Bull Valley district in September 1941. Two separate areas, the Pilot and the Cove Mountain, were investigated. The work was planned to increase iron-ore reserves for steel production in the Western United States. During the project period three diamond-drill holes aggregating 1, 000 feet were completed (fig. 2). The program also included 6 408 linear feet of surface trenching and 171 feet of underground work (figs. 2 to 8, inclusive). Analyses were made of 460 samples from the diamond-drill holes and surface and underground excavations. The results of the analyses are given in tables 1, 2, 4, and 5, and the logs of the diamond-drill holes are shown in table 3. Field. work was completed in September 1942.]

Jan 1, 1953

By R. F. Selden

The material in this paper is intended simply, to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions on various phases of the subject have been published, a few of which (4, 20, 25, 88, 90)4/ have more or less extensive bibliographies of tie earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon. dioxide with perhaps sore methane) is quite apparent.

Jan 1, 1934

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By Donald P. Schlick

This report presents a representative cross section of methods successfully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By S. M. Shelton, M. M. Fine, T. L. Johnston

"INTRODUCTION The Bynum property is about 15 miles west of Gadsden and 1 mile north of Walnut Grove, Etowah County, Ala. The ore lies in layers and as irregular masses and pockets in the clay residue from decomposed quartzite and limestone formations to the district.The property has been developed by means of numerous shallow shafts sunk to water level - about 25 foot. Operations are confined to small-scale, selective mining of pockets of high-grade ore. The ore is marketed directly, without beneficiation. The property does not yield a large amount of manganese ores. No estimates of reserve ore tonnages are available.A 206-pound sample was furnished for test. It was taken at random from a stock rile estimated to contain 130 tons of ore. The sample con¬sisted of a mixture of manganese oxides, iron oxides, and siliceous fragments in clay. The manganese occurred largely as soft, unconsolidated pyrolusite and wad. Some hard, crystalline pieces of psilomelane were distributed through the soft material. Small amounts of iron oxides were associated with the manganese oxides. Chert, quartzite, and clay comprised the gangue minerals.Dry analysis of the sample was as follows: 36.0 percent manganese, 6.1 percent iron, 2: .0 percent silica, 1.5 percent calcium carbonate, 0.36 percent phosphorus, 3.0 percent alumina, 2.2 percent barium, and 0.31 percent zinc."

May 1, 1942

By J. G. Kirby

The total number of petroleum refineries in the United States decreased during 1951, while the total crude-oil charging capacity continued to increase. There were 350 refineries as of January 1, 1952, compared with 357 a year earlier, according to the annual Bureau of Mines capacity survey. A gain of 369,241 barrels in daily refinery crude through-put capacity during 1951 brings the total to 7,332,885 barrels daily. The capacity of the average refinery to process crude-oil was 20,951 barrels daily, an increase of 1,445 barrels daily over the previous year. Capacity added in the Texas Gulf district accounted for 36 percent of the total increase; the Indiana-Illinois-Kentucky district, 23 percent; the East Coast district, 19 percent; the Oklahoma-Kansas district, 12 percent; and the Texas Inland district, 11 percent. The California district was the only one reporting a decline in crude-oil refining capacity, the total being 14,200 barrels daily below the previous year. Reported as under construction January 1, 1952, was an additional crude-oil capacity of 282,680 barrels daily, an increase of 77 percent over the January 1, 1951, total of 160,100 barrels. The capacity now building is for the expansion of existing facilities, since no new plants had been begun as of the first of the year. Three or four companies have plans to build refineries in the Williston Basin area of North Dakota, but no definite locations or dates when construction will begin have been announced.

Jan 1, 1952

By R. R. Wells

As a part of the strategic minerals program of the Bureau of Mines, nine chromite-ore samples were obtained during the period 1949-56 from mines in the vicinity of Red Mountain, near Seldovia, Kenai Peninsula, Alaska. This report summarizes the results of beneficiation studies of the samples at the Bureau's Juneau, Alaska, and Albany, Oreg., laboratories. In general, the ores were found amenable to concentration by gravity methods for producing concentrates that assayed over 48 percent chromic oxide. Intimate association of chromite and gangue minerals, however, necessitated fine grinding and limited the amount of chromite recoverable. Recovery of chromium in concentrate that assayed 48 percent chromic oxide or higher ranged from approximately 20 percent for low-grade ores (10 to 12 percent Cr203) to more than 95 percent for 1 high-grade sample (42 percent Cr203). The iron content of the chrome-bearing mineral -hence, the chrome/iron ratio of finished concentrate -appears to vary with the grade of the ore. Concentrates made from high-grade ores had chrome/iron ratios as high as 3.1:1; the concentrates from low-grade ores, however, had chrome/iron ratios as low as 1.8:1.

Jan 1, 1957

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of three samples collected from the Kidney seam, in the Northern Field of the anthracite region. Removal of the sink 1.70 specific gravity material from the samples collected would result in greatly reduced ash contents at yields in excess of 90 percent. The Kidney seam, in the locations sampled, proved to be a low-ash anthracite containing an unusually high percentage of float 1.45 specific gravity material.

Jan 1, 1970

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By Guy E. Dent, Robert S. Sandford, W. T. Millar, Hugo E. Kuehn

"INTRODUCTION AND SUMMARYDuring the latter part of 1943 a magnetometric survey was conducted by the Geophysical Division of the Bureau of Mines at the mine, Putnam County, N. Y., in an endeavor to locate a segment of the body that reports state was cut off by a fault. The Mahepac mine was abandoned about 1895 after producing nearly 1,000,000 tons of high-grade magetite iron ore. The results of the investigation indicate the termination of the ore body by ""pinching"" or a displacement of such magnitude as to place any extension at a considerable distance the original ore body. This report describes the work done on the project and presents the data obtained. ACKNOWLEDGMENTSThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. The Mahopac mine was visited by W.T. Millar, an engineer of the Bureau of Mines, on June 5, 1943, accompanied by Dr. William Agar of the Federal Survey, and again on July 29, 1943, accompanied by Dr. A. F. Buddington and H.F. Hawkes, both of the Geological Survey.The mineral investigation was under the general supervision of Paul M. Tyler, formerly regional engineer, Eastern Region; J. D. Bardill, formerly district engineer; and Dr. F.W. Lee, formerly chief. Division, Geophysical Exploration. The work was done under the immediate supervision of W. T. Millar, project engineer. The Geophysical Survey was made by Hugo Kuehn and Guy E. Dent."

Sep 1, 1948

As mine haulage vehicles become larger, the danger to a driver during a fire emergency is increased by the greater height of the cab above ground. Also, property damage due to fires on bigger trucks can be substantial. To solve this problem, the Department of Interior's Bureau of Mines, through two research and development contracts with FMC Corporation, San Jose, California, has developed two reasonably priced, reliable automatic fire sensing and suppression prototype systems for large haulage vehicles. At the onset of the large mobile equipment fire protection contract effort, it was learned that fires were frequently experienced in open-pit mine haulage equipment, especially large trucks. As the size of equipment has grown, so has the hazard presented to an operator forced to leave his truck in a hurry when fire breaks out and his normal path to the ground is blocked by flames. His only recourse is to jump from the cab platform to the ground, and the one-story drop of 10 feet or more can severely injure him. It is with these factors in mind that a program was undertaken to provide a fire detection and extinguishing capability tor the large mobile equipment, especially trucks, used in open pit mines.

Jan 1, 2012

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projets programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931