Search Documents

By S. H. Ash

The Pennsylvania anthracite region is composed of four fields, namely, the Northern, Eastern Middle, Western Middle, and Southern. It is in the eastern part of Pennsylvania and is shown on figure 1. The anthracite industry is confronted with a crucial problem of inundation by water impounded in underground pools in many mines and by infiltration of water from streams and pools on the surface (3). The deposits of anthracite in the United States are limited virtually to Pennsylvania, and the difficulties of this industry have been commonly considered as a State problem rather than a national one (1, 4, 6, 7). Anthracite was discovered in Pennsylvania in 1762, and the first mining company was formed in 1793. It was not until 1812 that anthracite began to receive recognition in the Philadelphia market as a domestic fuel, and by 1838 the annual production was nearly 1 million net tons. Since anthracite mining began, mine water has become progressively more difficult and costly to handle because of the extraction of anthracite both underground and along the outcrops of the beds, until at the present time mine drainage is a major anthracite-mining problem. Mine water is handled at the anthracite mines as follows: (a) by pumping, (b) by drainage tunnels, (c) by combination of pumping and drainage tunnels, and (d) by water hoists (hoisting water by means of large buckets) (4, 5,6, 7). This paper covers removal of the water from mines by means of pumping plants. Pumping is indispensable in the production of anthracite (5). The cost of pumping mine water has increased progressively since anthracite mining began. Some collieries have been forced to discontinue mining because of the high cost of pumping.

Jan 1, 1950

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008

By Kenneth L. Cashdollar

The Mine Safety and Health Administration (MSHA) and the West Virginia Office of Miners? Health, Safety, and Training (WVOMHS&T) investigated the explosion at the Sago Mine in West Virginia, which occurred on January 2, 2006, and resulted in 12 fatalities. As part of the investigation, the agencies requested that the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory evaluate the effects of explosions on specific mine ventilation seals and other structures and objects at its Lake Lynn Experimental Mine (LLEM). The results of the LLEM study would assist MSHA and WVOMHS&T in a more thorough understanding of the various questions that arose during their investigations of the explosion. Six large-scale explosion tests were conducted in the LLEM from April to October 2006. The protocols for these tests, and in particular the procedures for constructing various Omega block seals, were developed mainly by MSHA and WVOMHS&T. NIOSH developed the experimental procedures at the LLEM that would provide the required range of explosion pressures against the seals. Three 40-in-thick seal designs using Omega 384 low-density block were constructed in the LLEM and exposed to various explosion pressures. These seal designs are referred to in this report as the ?2001 design,? the ?hybrid design,? and the ?Sago design.? The 2001-design Omega block seal (80 in high) located in crosscut 2 of the LLEM survived all six explosions, with pressure loadings up to 51 psi. The 2001-design Omega block seal (88 in high) in C-drift was destroyed during Test 2, which subjected the seal to a head-on explosion that resulted in a pressure loading of 51 psi. The height difference between the two seals and the orientation of each seal to the explosion were contributing factors. The higher seal would be weaker for the same seal thickness. The hybrid Omega block seal in crosscut 3 survived an explosion at a pressure loading of 25 psi and failed during another explosion at a pressure loading of 39 psi at the seal. Based on these tests, it seems that the hybrid seal design is weaker than the 2001 seal design. The Sago Omega block seals were constructed in crosscut 3 and C-drift before Test 3. The crosscut 3 seal survived a pressure loading of 18 psi and was destroyed during an explosion at a pressure loading of 35 psi at the seal. The C-drift seal survived a head-on explosion that resulted in a pressure loading of 21 psi and was destroyed during an explosion with a pressure loading of 57 psi at the seal. Based on these LLEM tests, it seems that the Sago seal design is weaker than the 2001 seal design, yet it still complied with the requirements of 30 CFR 75.335(a)(2) that were in effect at the time of the mine disaster. During these LLEM explosion tests, the distance of seal debris travel was also measured. In Test 5, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 57 psi, and the seal debris was thrown over 500 ft. In Test 6, the C-drift seal was destroyed during a head-on explosion that resulted in a pressure loading of 93 psi, and the Omega block debris was thrown over 900 ft. During these tests, the explosion pressure effects on other structures and objects were also documented. Unless otherwise specified, all of the pressure data listed in this report represent the highest recorded smoothed (averaged over 10 ms) explosion pressure loadings. The information in this report was used by MSHA and WVOMHS&T as supporting data in their analyses and investigative reports of the Sago Mine explosion.

Sep 1, 2009

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

By Lloyd A. Morley

This eight-chapter document is the second volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. Building upon Volume I, the subject of protective equipment and relaying starts Volume II, first as an introduction in Chapter 8, then by a treatment of device selection in Chapter 9. Chapter 10 continues system protection in terms of transients and overvoltages. Chapter 11 describes the design of major power equipment, including power centers, switchhouses, and substations. Solid-state applications in mining are given in Chapter 12, and batteries and battery charging are discussed in Chapter 13. Chapter 14 covers electrical-equipment in hazardous locations of mining operations. The report concludes with Chapter 15, a discussion of electrical maintenance as well as some specific mine electrical problems. Information on surface and underground use is included in all these chapters. An index finishes the documentation and is cross-referenced to both report volumes.

Jan 1, 1982

By Allen G. Gray

It's not news to you that the United States is highly vulnerable to potential problems in supply of critical and strategic metals, and that these metals - chromium, for example - are employed in important bearing alloys. It's also not news to you that there is a significant challenge to improve durability and life of bearing systems which contribute to conservation as well as productivity. The objectives of this workshop are to identify available technologies and opportunities for new technologies in conservation, substitution, and displacement of critical and strategic metals in bearing systems. These considerations are among the most viable options for reducing vulnerability to a cutoff of chromium and other critical metals and action should be taken to identify and develop those technologies now rather than after a crisis is upon us.

Jan 1, 1984

[CONTENTS COUNTY NO. OF MINES MINE INDEX PAGE]

Jan 1, 1980

By R. W. Bee

This project, sponsored by the U.S. Bureau of Mines, Division of Environment, addresses two major subjects: refuse removal and subsidence monitoring. The refuse removal task consisted of developing a methodology for selecting the most economical combinations of coal mine breaker refuse and rock banks, disposal sites and material moving systems (trucks, trains, belt conveyers and pipelines). To prepare plans for moving refuse in the Lackawanna Valley of Northeastern Pennsylvania, refuse banks were inventoried, underground disposal sites identified and unit cost data prepared for the various material moving systems. The subsidence monitoring task consisted of defining the phenomenon of coal mine induced surface subsidence, establishing operational requirements, cataloging sensors and techniques to detect and measure subsidence and testing of the most promising techniques (photoelastic patch, tiltmeter, strain gage, microseismic and precise surveying). A preliminary system for a 700 acre area in Scranton utilizing 267 grid sensors, seven microseismic sensors and precise surveying techniques was designed with initial and annual operating costs determined. Two minor tasks supported both main subjects: zoning in the Northern Anthracite Field of Pennsylvania and Technology Transfer of subsidence vulnerability prediction techniques.

Jan 1, 1972

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSS systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By Mark P. Meyer

This U.S. Bureau of Mines publication presents salient information in abstract form on 247 coal deposits in Alaska. Coverage includes currently producing deposits and deposits that appear to have commercial production potential. Data arc taken from coal properties identified by the U.S. Bureau of Mines minerals availability program and by a literature search. Infrastructural and institutional factors affecting coal development in Alaska are also discussed.

Jan 1, 1987

By Jeffery L. Kohler

This final report on Bureau of Mines Contract J0338028 presents the results of a research effort to predict incipient failure in electric-power-system components. The development of continuous monitoring techniques to detect an incipient failure would represent a significant improvement in system maintainability, availability and safety, This report describes the analytical and experimental aspects of the project. Mathematical models have been developed to study the behavior of cables and motors which are undergoing a deterioration process. These models allow a detailed study of the effect of deterioration on the component's terminal characteristics and performance. The efficacy of using negative-sequence monitoring is a reliable indication of deterioration has been established. Techniques for assessing the sensitivity of the prediction algorithm to component deterioration have been presented. An approach for modelling electrically-excited vibrations, and including these in the algorithm, has been presented.

Jan 1, 1987

By Elaine T. Bowers

The Sunnyside single-entry project pioneered the use of single entries for longwall development in this country. During the 10-year course of the project, an immense amount of information was gathered. Over three miles of entries were observed primarily through instrument groupings placed in strategically located areas or "rooms." Nearly 1,200 instruments were monitored to gain information on the behavior of coal entries during development stages and through the mining of two longwall panels. This was one of the most extensively documented projects undertaken by the Bureau, The data gathered has a great potential for scientific research especially in the area of longwall mining. This Bureau of Mines report presents the ground control data gathered, in the form of computerized plots. Roof-to-floor deformation and load on cribs and roof bolts make up the bulk of the data, which is presented as load or deformation versus time. The plots are organized, generally, by the three main entries involved and, specifically, by the individual areas or rooms in those entries. No major attempt will be made, in this paper, to analyze the data other than to identify its source arid its history.

Jan 1, 1983

Fossil fuel consumption in the United States increased markedly over recent years, and future demands expect to be even greater. Coal, this Nation's most plentiful natural fossil fuel, will play a key role in fulfilling these demands. With expectations of increased coal exploitation, the U. S. Bureau of Mines authorized this project, the objectives of whi.ch were to prepare an authoritative report on current surface coal mining technology, to define current problems and possible solutions, and to project future developments necessary to assure adequate surfaced mined coal production to meet the Nation's future energy needs. These objectives we're accomplished by an extensive review of available published literature and data gathering field visits to active surface coal mines throughout the country.

Jan 1, 1975

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between Mdy 1983 and April 1984. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate. 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials.

Jan 1, 1984

By J. R. Hamke

THE WILLISTON basin is the largest known sedimentary basin on the North. American continent. Two-thirds of this large basin lies within the United States in Montana, North Dakota, and South Dakota. Less than 10 years after the first commercial oil discovery in North Dakota in 1951, the petroleum became one of the largest industries in the three-state area. Crude petroleum is now the most valuable mineral resource in the area. In 1960, the basin produced 39 million barrels of worth $100 million at the wellhead. Most of the 137 oil pools covered to date are in Paleozoic carbonates at depths ranging from 3,000 to 13,000 feet. The major producing fields, centered on the Cedar Creek anticline in Montana and the Nesson anticline in North Dakota, produce from depths below 6,000 feet. This report presents descriptions of all phases of the Williston basin petroleum industry, including leasing, exploration, geology, drilling, production, transportation, and refining. Engineering, physical, and production data, maps, and crude petroleum analyses for 137 separate oil pools are included.

Jan 1, 1966

Papers presented at a U.S. Bureau of Mines (USBM) technology transfer seminar describe the causes of violent material failure in U.S. mines, measurement techniques for monitoring events that result in violent failure, and mitigation techniques for controlling failure. Specific factors contributing to violent failure are identified on the basis of geotechnical monitoring in 16 U.S. hard-rock and coal mines and on statistical analyses of 172 coal bump events. New monitoring and analysis techniques developed as tools for assessing violent failure; geotomographic methods that provide new capabilities for the study of material failure and stress changes over large areas; and seismic methods for determining source locations, calculating energy release, and determining source mechanisms are described. Fair correlations have been established among seismic parameters, elastic stresses, face support load, and violent events. USBM studies have identified the advantages using both yielding and stable pillars for coal bump control. A computer program has been developed as an aid for selecting room-and-pillar layouts. The practical aspects of implementing a destressing program is outlined for coal mines, while the importance of mine orientation and timely support installation in controlling buckling-type failure is identified for hard-rock mines.

Jan 1, 1995

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977