Search Documents

By F. N. Bender

Percolation leaching of wad-type manganese ores was investigated, using a novel system of alternate upward passage of sulfur dioxide gas through moistened ore and downward percolation of wash solutions to extract solubilized manganese. Bench and large-scale tests designed to simulate vat and heap leaching were made on four wad ores from Arizona and Nevada and on a pailomelane ore from Arizona. Three of the wad ores required prebaking at 500° to 600° C. to produce a permeable agglomerate that would not slake during percolation washing. The hard-type ore and one of the wad ores that contained a large amount of granular gangue did not require prior roasting. The deportment of the different ores toward leaching and percolation was studied with particular reference to the influence of the sulfur dioxide - oxygen ratio and the effect of gas dilution on the rate of manganese dissolution, dithionate formation, and acid production. Crushed charges of the ores, as coarse as 1 inch and as fine as 1/4 inch, were treated for periods of 5 to 11 days. Percolation of the gas and leach solutions through the charges was achieved without difficulty. The manganese extractions varied between 78 and 97 percent and depended upon the size and type of ore leached. The average quantity of sulfur dioxide required in the larger scale tests was about 2.6 pounds per pound of manganese recovered. The dithionate formation varied from 0.35 to 0.9 pound per pound of manganese extracted depending upon the strength of leaching gas.

Jan 1, 1957

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By R. L. Grant

During the last decade or more , experimental research on commercial detonators used for initiating the detonation of dynamite and other high explosives has led to important improvements . Developments , especially in the United States , have been directed toward improvement in the construction of detonators to make them safer to manufacture and use . More suitable and safer initiating charges also have been found . Although for many years mercury fulminate was unrivaled as the initiating charge for dynamite , during the last decade it has been replaced to a large extent by less sensitive , more efficient, and cheaper combinations of ignition , priming , and base charges . Commercial detonators were once of relatively simple construction and almost universally identical . Today they are technically complex, with special nodifications for particular uses ; they have developed along different lines n various countries and even among the several manufacturers within any one country .

Apr 1, 1943

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. When enough circulars have boon completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed b., bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual nines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); Ventilation; wage, contract and bonus systems, etc.

Jan 1, 1931

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967

By R. L. Soderberg

Large open stopes mined by vertical crater retreat or sublevel s are sometimes backfilled with uncemented sand to support the stope walls and alleviate rock bursts. The failure of bulkheads in two different mines prompted a research project at the Bureau of Mines to prevent a recurrence of these failures. A series of laboratory tests with drains and sand filters was conducted to measure the bulk-head pressures when adequate drainage was maintained. Results showed that bulkhead pressure was reduced to near zero while drains were in operation, as compared to full hydrostatic pressure when drains were blocked or drainage was restricted. A relatively simple, free-draining bulkhead was shown to be adequate.

Jan 1, 1985

By Thomas K. Matson

The coal reserve base in the Western United States is presented for coalbeds amenable to extraction by underground mining methods. The Federal Bureau of Mines has abstracted data on the quality and quantity of coal resources/reserves from numerous State and Federal publications and modified such data as necessary to allow computer storage and retrieval. Tonnages are compiled by State, county, coalbed, and rank, and allotted to sulfur categories by statistical apportionment. The coal reserve base in those States west of the Mississippi River, amenable to underground mining, is estimated to be approximately 131 billion tons. Of this total, about 30.8 billion tons are bituminous coal, 100.2 billion tons are subbituminous coal, and 126.4 million tons are anthracite. Lignite is not considered for underground mining in this report. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves as jointly defined by the Bureau of Mines and U.S. Geological Survey. The purpose of this system is to provide for direct comparison or compilation of various resource/reserve data.

Jan 1, 1975

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States during the years 1958 through 1960. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included. Silicosis statistics reported by the U.S. Public Health Service indicate a sizable silicotic population in the United States and suggest a need for greater dust-control effort. A joint medical-environmental survey was begun by the U.S. Public Health Service and the Bureau of Mines to evaluate the magnitude of the silicosis problem in the metal mining industry in the United States.

Jan 1, 1962

By J. Howard Bird

The purpose of this publication is to discuss grounding mediums and the phases of grounding related to corrosion and cathodic protection. The material presented is believed to contribute to a better understanding of this subject. It also indicates more effective methods of reducing corrosion damage to metal structures and equipment in the mining industry by cathodic protection. The authors do not intend to discuss technical aspects but rather to explain the general principles of this method of inhibiting corrosion. The relationship between soil resistivity, protective grounding, and corrosion is presented. Corrosion causes the annual loss of billions of dollars; which can be greatly reduced. Losses in the mineral industry can be excessive owing to the extensive use of direct-current power, the presence of considerable dampness, and the frequent, indiscriminate use of dissimilar metals.

Jan 1, 1958

By Glenn A. Shirey

The objective of this contract as to prepare a detailed, readily usable handbook on dust control techniques for longwall mining operations. Information was gathered from available literature, and through contacts with industry and government personnel. The handbook describes those methods of dust control applicable to today's longwall mining systems, and contains sufficient design elements to assist operators with problems in testing or implementing new control procedures. Complete reference lists are presented at the end of each chapter to direct the reader to additional information.

Jan 1, 1985

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants. On account of extensive folding and faulting of the coal measures, mining in Washington presents many difficulties; therefore a description of the methods employed at some of the mines may be useful in planning operations in other regions, and is presented in this bulletin. The coals of Washington differ in quality, ranging from true lignites in Cowlitz County in the southern part of the State to anthracites in the Mount Baker district of Whatcom County, in the north~ rn part. Most of the output consists of subbituminous and bituminous coals, the latter including both coking and noncoking varieties. Analyses of the coals of the State and descriptions of the beds from which the samples were taken have been printed in publications of the United States Bureau of Mines.2 Details of coal beds and analyses of the coals of King, Kittitas, and Pierce Counties have also been published by the Washington Geological Survey; 3 and most of the coal beds of the State are described in some detail in a bulletin of the United States Geological Survey.4 In 1918 mining was in progress at 72 mines in the State 4a; 46 of these mines each employed more than 10 men underground. These mines were distributed as follows: Thurston County, 1; Lewis County, 7; Kittitas County, 14; King County, 16; Pierce County, 6; Skagit County, 1; and Whatcom County, 1. During that year a total of 5,847 men were employed, 4,172 underground and 1,675 on the surface. The average number of days worked in the State was 275, and the average yearly output per man was 706 tons. Coke is made only in Pierce County by four companies, which have a total of 341 beehive ovens. In 1918 they produced 93,699 tons of coke. Up to 1919 mining machines were little used in the State. In 1917 only 6.61 per cent of the coal :produced was undercut by machines. In that year 58.95 per cent of the coal was mined by hand, and 34.44 per cent was shot off the solid. The explosives used were as follows: Black powder, 36.6 per cent; dynamite, 38.l per cent; and permissible, 25.3 per cent. The State of Washington is divided naturally into two parts by the Cascade Mountains which extend north and south somewhat west of the middle of the State. The coal areas east of the range will hereafter be referred to as eastern Washington-though nearly all of it is west of the middle of the State-and that on the west side as western Washington. The geographical distribution of the coal fields is shown in Plate I. Exploration of the State has not been exhaustive enough to preclude the possibility of discovering, besides the foregoing, other districts that contain deposits of coal in commercial quantities.

Jan 1, 1924

By Arthur Matzick

[1-1 1y IilJLJ,I~X" K pl.rw~~ts rt1s11l s I'I.IIIII 1.c1sc.n rcnlb cind d(~\,elopmrnt rnr- ried oitt by tllc* Illll.cv111 of .\li~~css (111 rlrc. ~ns-c-o~l~l)i~s~io~l oil-sllnlr rcdorting proc-rss. 15ffrc~t.s of t l\t. 1)roc.cBss ra~~irtl~lrs, resi~lts of ~ILS altrl stinle distribu- lion stutlic~s, lrsls 011 sl1nlr I)III-~ ic.lt* sixit. :rl~tl o1hi11- cl~*ti~ils of tks )erimrntnl pro- pSnrns arc* (lisc-~rss*tl. l-~trii)~~~ ~IIIS~~~ZII.~ ~II[O~IIIII(~III~ 111111 pr111) \ CI~S ~s~ocinted ill^ 11~r relurti~bg 1)1-o(.e1ss ,~lso 111.c. i~~c~l~~tl~.tl. "~'~I~III~I~I iolls of tl~r rrtorting test c1:itn I~II(~ elct~tilwl oil rc~~overv [I[I\v I~~~~~I-IIIIIS for tl~c* (i-, 25-, IIIIC~ 150-ton-per- clay rrtorts, tin1.1 tl~-n\vings reirlt illK 10 1.c1to~t i11g .rc.li~ip~llr.~~t nre given. ]

Jan 1, 1966

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

By Henry Kreisinger, WALTER T. RAY

In its investigation of more efficient methods for utilizing the coals and lignites in the United States, to the end that waste might be avoided, the value of low-grade coals increased, and the life of the nation's fuel resources prolonged, the technologic branch of the United States Geological Survey carried on a study of the factors involved in the manufacture and use of briquets, including the suitability of various coals for briquetting, the cheapest and most satisfactory binders, and the furnace behavior and evaporative efficiency of briquetted fuel. The investigations had their beginning in the work done at the coaltesting plant at the Louisiana Purchase Exposition, St. Louis, Mo., in 1904, and were continued at St. Louis and later at Norfolk, Va. Accounts of various tests and statements of the conclusions to be drawn from them have appeared in a number of bulletins. a In connection with the work at Norfolk, comparative steaming tests were made in stationary, marine, and locomotive boilers with run-ofmine coal and the same coal formed into briquets of two sizes. The tests in a locomotive boiler that are described in detail in this bulletin were undertaken to add cumulative evidence to work done at other places. They were made possible through the courtesy of the Seaboard Air Line Railway Company in supplying both the locomotive and the coal used. During the trials the locomotive stood on a side track in the shop yards of the railway company at Portsmonth, Va. No running tests were made.

Jan 1, 1911

By E. D. Gardner

Open-cut mining of copper ores in the western United States is a relatively new industry. At first the mining methods were mainly adapted from those used at open-cut iron mines and at quarries, but now efficient practices that are more suitable for the copper deposits have been developed. The pioneer in this field is the Utah Copper Co., of Bingham, Utah, which deserves great credit for working out much of the early procedure. Stripping began at that mine in 1906, and the large Garfield concentrator was put in commission in 1908. Next in order of development were the Nevada Consolidated Copper Co., at Ely, Nev. ; the Chino mine of the Ray Consolidated Copper Co., at Santa Rita, N. Mex. ; the New Cornelia Copper Co., at Ajo, Ariz. ; the Sacramento Hill mine of the Copper Queen Branch, Phelps Dodge Corporation, at Bisbee, Ariz.; and the open cut of the United Verde Copper Co., at Jerome, Ariz. The Sacramento Hill mine began to produce in 1923, and the United Verde open-cut mine has produced ore mainly in connection with stripping. The writer visited the Utah Copper mine in September, 1923; the Nevada Consolidated in August, 1923; the Chino in July, 1924; and the New Cornelia, the Sacramento Hill, and the United Verde open cut at various times during 1922, 1923, 1924, and 1925, mostly in connection with other work.

Jan 1, 1927

By J. J. Forbes

This publication is a revision of the first of a series of four Miners' Circulars originally prepared and issued in 19'29 for use in a course of training designed to prepare mine officials to organize men for rescue and recovery operations. These circulars were revised in 1937 and 1938 and again in 1948. This circular (Miners' Circular 33) discusses mine gases and methods for detecting them. The second of this series (Miners' Circular 34) gives instruction in Bureau of Mines methods of sampling and analysis of mine gases; the third (Miners' Circular 35) describes methods and equipment used for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures used in sealing and unsealing mine fires and in recovery operations after mine fires or mine explosions.

Jan 1, 1954

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By Vincent Castranova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

"A group of bisbenzylisoouinoline alkaloids has been shown to exhibit various degrees of effectiveness in preventing silica-induced fibrosis in animal models [1, 2]. The objective the present study was to characterize the binding of several of these alkaloids to phosphatidylcholine vesicles and rat alveolar macrophages using fluorometric and equilibrium dialysis methods, respectively. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, chiral configurations, and double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is a highly effective agent in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, certain analogues of tetrandrine such as curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In conclusion, the results of these studies indicate that alveolar macrophages exhibit large binding capacities for certain members of this class of bisbenzylisoquinoline alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds. These data also suggest that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.INTRODUCTIONInhalation of crystalline silica is associated with the development of silicosis. This fibrotic disease is characterized by the appearance of concentric hyalinized nodular lesions in the lungs with the progressive development of pulmonary dysfunction [3, 4]. Many theories concerning the etiology of silicosis involve silica-induced activation of alveolar macrophages. Evidence indicates that in vitro silica exposures result in the generation of chemiluminescence, and the release of superoxide and hydrogen peroxide from alveolar macrophages [5]. Activation of alveolar macrophages has also been demonstrated after intratracheal instillation or inhalation of silica [5, 6]. Such excess release of reactive products from pulmonary phagocytes has been associated with damage to the lung parenchyma [7, 8]. In addition, silica exposure results in the release of mediators from alveolar macrophages, which enhance proliferation of fibroblasts and collagen synthesis by these pneumocytes [9-12]."

Mar 1, 1992