Search Documents

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946

By G. E. McElroy

The purpose of tins paper is not to present new date on the pressure losses due to bends and chances of area in mine openings through which air flows, but rather to correlate existing data, determined mainly on small duct systems and expressed in a variety of ways, according to uniform methods that facilitate their use in pressure-loss computations. These are required in such, air-flow problems as determining the quantity that will flow through is mine openings under a certain pressure difference or, conversely, the pressure difference that will be required to maintain a certain rate of flow. Air flowing through h ducts, such as mine airways, encounters resistance to flow due to interference of the individual air streams with each other caused by the wall surfaces. The result is that part of the kinetic energy of the flowing stream is converted to heat; and constant renewal of the kinetic energy from the total energy of the flow is required to maintain it. This process manifests itself by a decrease of the total pressure (static pressure plus velocity pressure; of the air in the direction of flow; in order that flow pray occur, there must necessarily be a differences in total pressure between the two cads of the air-ay equivalent to the pressure losses occasioned by the flow, which automatically adjusts itself in magnitude to the pressure difference maintained.

Jan 1, 1932

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985

By Guy A. Johnson

Combining contract and in-house research, the Bureau of Mines has developed and inmine-tested a novel device to improve the field-of-view of operators of off-highway mining equipment. This device utilizes a downward-looking, flat fresnel lens. The lens, plus louvers to reduce glare, is housed in a protective steel structure. The complete unit is called a blind area viewer. The viewer, when mounted on the right- front corner of the deck of most large haulage trucks, will increase a driver's direct field-of-view from about 35 pct (of where he/she has to drive) to about 80 pct. The improved visibility allows the driver to see possible collision hazards and roadway obstacles better, thus improving mine safety and increasing productivity. Economic analysis shows that the blind area viewers, which are now commercially available, pay for themselves in about a month on a 170-ton-capacity truck. The viewers are also applicable to other large mining equipment, such as front-end loaders, draglines, and downhole drills, or any place where seeing around a corner would be advantageous, such as along conveyor flights in processing plants during startups.

Jan 1, 1983

By Edward F. Redente

Several research projects have been conducted in the western United States to determine the optimum soil replacement thickness for reconstruction of rangeland and cropland. However, the information gained from these studies tends to be site-specific and not broadly applicable. Moreover, the possible interaction between soil thickness and mechanical and fertilizer manipulation of the overburden has not been adequately studied. To meet these information needs, research was initiated at Trapper Mine in northwestern Colorado in 1980 to study vegetation response to soil thicknesses of 15,30,45, and 60 cm and five manipulations that included disking, ripping, and fertilizing. All crops were harvested at peak standing crop and then weighed in the laboratory. Wheat grain yields were highest when soil thickness was 45 cm and the soil and overburden were ripped. Alfalfa yields appeared to be highest when overburden was disked and fertilized and soil was replaced to a thickness of 60 cm. For range vegetation, standing crop biomass was highest when overburden was ripped and soil was replaced to 60 cm thick. However, optimum performance was obtained from the maximum number of species and life forms by disking overburden and replacing 15 cm of soil. The performance of most range plant species has improved over the three years of the study. When the results of this study are compared to the results of other soil thickness studies, we can conclude that selection of management practices should be influenced by local climate, local soil and overburden conditions, type of crop or vegetation to be grown, and specific management goals for that crop or vegetation.

Jan 1, 1984

By D. H. Platt

Gypsum and gypsite, used in the manufacture of plaster and plaster products, have been mined from deposits near Acme, Hardeman County, Tex., for more than 30 years. The Certain-toed Products Corp., 120 East Lancaster St., Ardmore, Pa., operates the Acme, Tex., mine. Underground hauling was done with storage-battery and Diesel-electric-powered shuttle cars. Many mining companies and individuals have manifested interest in all types of equipment powered by Diesel or Diesel-electric units, as attested by the recent increase in use of Diesel-powered equipment in underground metal and nonmetal mines. The purpose of this paper is to describe the manner in which a storage battery-powered Joy Model 60D2 shuttle car was converted to Diesel-electric power. The conversion was made, at the instance of the operating company, by Stewart & Stevens on Services, 4801 Lemon Ave., Dallas, Tex. This is believed to be the only such converted shuttle car in use.

Jan 1, 1950

By Forrest T. Moyer

The overall disabling work injury experience, excluding office- workers, at nometal mines and mills during the period 1961-63, as reported to the Bureau of Mines by operators, was 77 fatal and 7,201 nonfatal injuries during an aggregate worktime of 335,029,685 man- hours. These injuries, fatal and nonfatal combined, occurred at a frequency rate of 21.72 per million man-hours, comprising 0.23 for the fatal and 21.49 for the nonfatal injuries. The combined severity rate of the disabilities was 2,312 days lost or charged per million man-hours, consisting of 1,379 for the fatal and 933 of the nonfatal injuries, The average severity of all disabilities during 1961-63, was 106 days per injury, The number of days lost or charged, excluding officeworkers, at nonmetal mines and mills during 1961-63, was 462,000 days charged to fatal injuries and 312,461 days lost from nonfatal injuries. The outstanding causes for fatal injuries were explosions (18 fatalities occurred in a major mine-explosion disaster in a potash mine in Utah in 1963) and falls of rock or ore from back or side, while most nonfatal injuries were caused by handling materials, slips or falls of persons, haulage, and machinery. The parts of the body most frequently injured during the period 1961-63 were the trunk, hand and finger, and foot and toe, An average of 52,810 men were at work daily, There were 20 nonfatal disabling injuries reported for office- workers at nonmetal mines and mills during the period 1961-63 during an aggregate worktime of 23,088,496 man-hours, These injuries occur- red at a frequency rate of 0.87 per million man-hours, There were no fatal injuries reported.

Jan 1, 1967

By Donald W. Ross

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk—type sagger sponge iron, has an excellent reputation as a superior furnace feed wherever high—grade steels are made. The general procedure for making brickyard sponge iron was described frequently in Swedish technical journals prior to 1932 and at that time consisted in filling clay refractory containers, called saggers, with a super-concentrate of Gellivare magnetite plus the necessary amount of solid reducing agent and desulfurizer and then firing in a Hoffmann ring furnace, as used in the ceramic industry.The early Swedish publications describe two types of brickyard sponge iron: (1) An inferior high-sulfur product obtained by mixing the ore and reducing agent, and (2) a high-grade low-sulfur product in the form of coherent disks 7 to 9 inches in diameter and 1 to 1-1/2 inches thick made by the saggers with alternate layers of solid-fuel reducr and of uniaxed ore."

Sep 1, 1945

By P. Nicholls

[This paper sets forth the burning characteristics of coke used as a domestic fuel as shown by work of the U. S. Bureau of Mines and others. Coke is a truly smokeless solid fuel and is held in high regard for this quality. Ways are being found for making commercial coke from a wider range of cools than heretofore, and tale use of coke for domestic heating is increasing. ACKNOWLEDGMENTS The experimental work reported in this paper was conducted at the Pittsburgh Experiment Station of the U. S. Bureau of Mines cinder the authority of O. P. Hood, chief mechanical engineer; M. L. Orr, assistant feels engineer, and W. M. Brewer, junior fuels engineer, assisted by Charles Schramm cooperated in making the tests.]

Jan 1, 1929

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By H. F. Yancey

Traditionally the Pacific Northwest has relied on hydroelectric power, which has been both abundant and cheap. However, comparatively few hydroelectric sites capable of providing low-cost power remain, therefore the need for supplemental thermal generation, perhaps within the next decade, is generally recognized. Based on the present cost and availability of competing fuels, coal seems to be the logical choice for projected thermal power plants. Power companies and public utilities have become interested in establishing reserves of coal for future use. One deposit explored in 1958-59 lies in southern Thurston and northern Lewis Counties, Wash., near Centralia. Drilling, totaling 22,700 feet, proved the existence of 70 million tons of strippable coal--an ample reserve for the projected power plant. The coal, like most others and particularly those of Washington and Oregon, when mined in full seam section by mechanical methods, would require cleaning to make it suitable for use. The amount and nature of the impurities in this coal dictated a thorough investigation of its cleaning characteristics to establish economic factors and to insure proper preparation-plant design. Therefore, arrangements were made through a cooperative agreement to conduct such work at the Seattle Coal Research Laboratory of the Bureau of Mines. This report describes that investigation. The results are of interest primarily in connection with the utilization of this particular deposit, but some of the information developed is applicable to other deposits of low-rank coals in the West, because the impurities in these coals differ greatly in behavior from those generally associated with the higher rank coals of the Appalachian field.

Jan 1, 1961

By Jr. Taylor

The following heats of solution have been measured in 1.160 molal H2SO4 at 25° C: AH298, kcal./mole Be(c) + 77.44(H2SO4?47.849 H2O) H2(g) + BeSO4 (soln) -92.83 ± 0.11 BeSO4 ?(c) + 77.44 (H2SO4?47.849 H2O) BeSO4(soln) -16.45 ± 0.02 BeSO4?2H2O(c) + 77.44(H2SO4?47.849 H2O) BeSO4?2H2O(soln) -5.395 ± 0.019 BeSO4?4H2O(c) + 77.44 (H2SO4?47.849 H2O) BeSO4?4H2O(soln) 1.513 ± 0.010 Combining these data with other experimental results and data taken from National Bureau of Standards information yielded the following heats of formation at 298° K:

Jan 1, 1966

By R. Wiebe

During a recent investigation the authors were interested in determining: (1) How many points were necessary to locate the deviation curve for copper-constantan thermocouples within an accuracy of about 0.05° C., used in connection with the, "standard" thermocouple of L. H. Adams (2) Whether copper-constantan thermocouples showing considerable deviations from the "standard" were consistent throughout their calibration. (3) How reliable the extrapolated portion is - that is, the interval between -183 and -220° C. of the "standard" thermocouple.

Jan 1, 1931

By G. J. Perrott, H. W. Clark

During the course of the cooperative smoke abatement investigation carried on by the Bureau of Mines , the city of Salt Lake and the University of Utah during 1919-1920 , a study was made as to the suitability of Utah coals for by-product coking with particular reference to low temperature coking . was done because it was realized that a smokeless fuel for domestic consumers was the best remedy for this class of smoke producer . A report of the technical side of the work was included in the final report of the cooperative investiga- Since this report was written (June 1 , 1920) further work has been done by other investigators .

Apr 1, 1922

By Earl T. Hayes

THIS BIBLIOGRAPHY has been assembled to aid research by the Bureau of Mines, and others on high-purity tungsten. It appears approximately 50 years after the development of ductile tungsten-one of the first metals to be produced in a high-purity form. Requirements of the missile age are ever more demanding that engines rout hotter and space vehicles fly higher and faster. Thus, it has become necessary to reexamine all conventional materials of construction as well as to investigate new combinations. At this stage of our technology we have alloys capable of operation at 1,800° F. and several possibilities of developing some. that will be satisfactory up to 2,500° F. Strength-weight comparisons, detrimental to tungsten at, lower temperatures, disappear at this point, mid tungsten or its alloys appear to be the only metal capable of operation at truly high temperatures. The aim of this bibliography has been to include only references that concern improving the purity of tungsten-from processing the ore to treating the finished metal. In this sense it is a selected and not a critical bibliography. The period front January 1911 through February 1959 has been covered. Because repent literature has the greatest, value, most of the selected items refer to publications issued within the pest 5 years.

Jan 1, 1960

By R. Wiebe

During a recent investigation the authors were interested in determining: (1.) How many points were necessary to locate the deviation curve for copper-constantan thermocouples within an accuracy of about 0.05° C., used in connection with the "standard" thermocouple of L. H. Adams. (2.) Whether copper-constantan thermocouples showing considerable deviations from the "standard' were consistent throughout their calibration. (3.) How reliable the extrapolated portion is - that is, the interval between -183 and -220° C. of the "standard" thermocouple. It seems that a calibration between 0 and -193° C. can be made within the stated accuracy by determining experimentally the e.m.f. of the particular couple at -78.50°, the normal sublimation point of carbon dioxide, and at -182.97°, the normal boiling point of oxygen. Substituting the values found for the two fixed points in the simple quadratic. Equation

Jan 1, 1931

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture filling and associated alteration on the mechanical behavior of rocks. Results are presented for specimens from the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from 1) Climax, medium-grained - granite, fine-grained granite, granite porphyry, schist, and gneiss; 2. Henderson, rhyolite porphyry; 3. San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineral composition, composition and fabric of fracture fillings, density and porosity. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic relocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Tentative conclusions are that some relation appears to exist between compressive strength and the following properties and features for all the specimens: dynamic Young's modulus, sonic velocity, density, rock composition, and composition and fabric of fracture fillings - veinlets. There appears to be some relation between compressive strength and Shore scleroscope hardness and porosity for quartz monzonite (San Manuel). A relation appears to exist between compressive strength and texture for schist and between com¬pressive strength and extent of failure on fracture fillings for fine-grained granite, schist, and gneiss (Climax). We plan to perform additional analyses of data collected so far and data yet to be collected in the next few months, with emphasis placed on devising a practical index of alter¬ation that can be used in the field. Limitations on interpretations arise from such factors as heterogeneity of the rocks studied, the small range of confining pressures used, and other factors presented in the text.

Jan 1, 1973

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By Wilford S. Wright, Harold E. Heide, Robert L. Thorne, Neal M. Muir, Aner W. Erickson, Bruce I. Thomas

A program of investigation of strategic and critical minerals began in 1940 to examine and develop tungsten occurrences in the western United States and Alaska. During the years in which the nation was at war, this work was given special impetus to stimulate domestic production. This report is a compilation of results of the tungsten investigations in Alaska supplemented by certain data made available by the Territorial Department of Mines and is designed to include in its scope descriptions of all known tungsten occurrences in the Territory. Two areas in Alaska warranted special investigation - one at Gilmore Dome, 16 miles northeast of Fairbanks, and the other in the Hyder District, at the head of Portland Canal. Three tungsten properties - the Stepovich, Colbert, and Yellow Pup - are at Gilmore Dome. The Stepovich property, referred to sometimes as the Cleary Hill tungsten deposit, was worked by the Cleary Hill Mines Co. from April 1942 until May 1944 and was first examined by Robert S. Sanford and Norman Ebbley, Jr., engineers of the Bureau of Mines, in September 1942. The Cleary Hill Mines Co. by that time had explored an 800-foot strike length of the ore zone with 10 bulldozer trenches and was sinking an inclined shaft on ore in the central portion of the explored zone. In January 1943, the senior author, in company with Ebbley and Harry C. Doheny, supervising engineer of R.F.C., examined the property. Preliminary work by the Bureau of Mines began in May 1945, but actual exploration did not commence until late in June and continued until the end of October 1943. The deposit was examined by John B. Mortie, Jr., and William C. Overstreet, of the Federal Geological Survey, in 1942, and this study was continued in 1943 by Frank Byors, who also assisted the Bureau’s engineers on geologic problems. A magnetometer survey of this area was undertaken in 1942 by Henry Joosting and Eskil Anderson, engineers of the Territorial Department of Mines, and was completed with Bureau of Mines assistance in 1943. During 1943 the Bureau completed exploratory projects on the Cleary Hill mine and adjacent Colbert prospect. The field work on the Colbert property was begun early in July 1945 and continued intermittently until the end of October 1943, when it was recessed because of subzero weather. During September 1944, the Bureau of Mines established (by means of a few surface trenches) continuity between the Colbert mineralized zone, high on the dome, and the Yellow Pup vein, the lowest known tungsten mineralization in the area. It is generally recognized that any extensive program to develop the area as a whole logically would be carried out from the lower horizon.

Jun 1, 1948