Search Documents

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intensive three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By B. H. Clemmons

A field method has been devised for rapid determination of heavy minerals occurring in the unconsolidatod beach and dune sands. The method has been proved practical by usage in field evaluations of several hundred beach- and dune-sand samples in the Florida area. The simple equipment required and the techniques involved are described. Other data show that the method is relatively insensitive to variations in the mineralogical content or size distribution of the mixed heavy minerals contained in the samples tested. A modification of this procedure, found to be suitable for plant use in determining the relative purity of heavy-mineral flotation concentrates, is also described. A specific application is determination of the amount of feldspar-quartz in spodumene flotation concentrates. The results of the rapid evaluation techniques closely approximate those obtained by more precise laboratory procedures.

Jan 1, 1957

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

By J. B. Littlefield

[At B. meeting of the Subcommi ttce on Chemica.l _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of \~nes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a r?ference ]

Jan 1, 1938

By Howard P. Hamlin, John W. Sweeney

Shales , clays , and loess in Iowa were tested and evaluated to determine feasibility of producing lightweight aggregate by commercial rotary - kiln or sintering methods . Preliminary testing was conducted in a muffle furnace . Rotary - kiln tests were conducted in a 16 - inch by 14 - foot rotary kiln . Concrete cylinders and cubes were tested to determine qualities of the aggregate . Three samples made suitable lightweight aggregate by rotary - kiln methods and two by sintering .

Jan 1, 1964

By Fay B. Dillard

This Bureau of Mines report reviews the disposition of natural gas as delivered to industrial consumers via main line sales. Salient information on main line, or direct, natural gas sales to industrial users is presented by State) standard industrial classification code (SIC) revenue, and type of sales for the years 1968 through 1973.

Jan 1, 1975

By John W. Finch

The Secretary of the Interior acting through the Bureau of Mines and the Geological Survey is authorized by the Strategic Materials (Public No. 117 - 76th Cong., Chapter 190 1st Sess.) to make investigation concerning essential minerals of which the quantities or grades obtainable from known domestic sources are inadequate. The Bureau of Mines, in carrying out its part of this program, may investigate deposits of such minerals in whatever manner may be necessary, in order to determine (1) the extent and quality of the are, (2) the most suitable method of mining and beneficiating it, and (3) the cost at which it may be produced. The essential objective in doing these things is to determine where and how supplies of minerals and metals of which domestic production is usually inadequate might be obtained in a national emergency, even though at higher cost than usual.

Jan 1, 1939

By Alfred E. Schwaneke

A versatile torsion creep tester was instrumented with electromechanical and servomechanical components to operate automatically and unattended, producing digital printed outputs. The apparatus uses an electrical system for applying torsional stresses, and a unique angular transducer as a null detector operating a servocontrolled strain measuring system with the digital readout. The tester is designed to measure the creep in single-crystal or polycrystalline zinc, zinc alloys, magnesium, magnesium alloys, or other metals and alloys. Applied stresses may be varied from zero up to 2,000 psi in the outermost fibers of a 1/8-inch-diameter, 4-inch-long specimen. Strain readings to 0.001 degree, equivalent to a strain of 2.73 X 10-7, may be made automatically from one every 5 seconds to one per month. The apparatus has provisions for programed temperature control and special atmospheres or vacuum operation. A discussion of applications of the system to other mechanical testing apparatus is included.

Jan 1, 1970

By K. O. Bennington

The thermodynamic properties of pollucite [(Cs0.650Na0.185Rb0.028)(AlSi2) (05.8630H0.137)?0.19H201 were determined by the Bureau of Mines in collaboration with the Argonne National Laboratory. The standard enthalpy of formation determined by hydrofluoric acid calorimetry is ?Hf°298 = -3,098.52 ±3.63 kJ mol-1. The standard enthalpy of formation from the oxides is ?H298 (from oxides) = -209.50 ±2.38 kJ mol-1. Low-temperature heat capacities were determined by adiabatic calorimetry from 5.0 to 306.1 K. The derived standard entropy is S°298 = 207.24 ±0.43 J mol-1k-1. Enthalpy increments above 300 K were measured by copper-block drop calorimetry from 349 to 674 K. Various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation and Gibbs energies of formation are given as functions of temperature. The Gibbs energy of formation is ?Gf°298 = -2,919.9 W mol-1

Jan 1, 1983

By William E. Dennis

"INTRODUCTION The San Antonio Canyon prospect was examined by engineers 3/ of the Bureau of Mines in March 1943 and again in October 1944. In July 1944, the United States Geological Survey mapped the prospect and submitted a report 4/ recommending core drilling by the Bureau of Mines. The drilling project, which was supervised by the author, was started on January 10 and completed on May 10, 1946.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. Acknowledgment is made to W. D. McMillan, engineer in charge of the Austin field office, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, for general direction and advice. The samples were analysed in the laboratory of the Metallurgical Branch at Rolla, Mo., C. Travis Anderson, chief."

May 1, 1947

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By V. A. Marple, K. L. Rubow

"4.1 IntroductionIn previous chapters impactors have been described as useful instruments for classifying particles by their aerodynamic diameters and for measuring particle size distributions. These impactors can be used most reliably if the user has some understanding as to how the impactor classifies particles and what parameters are important in this classification process. This understanding can best be obtained by a theoretical inspection of inertial principles.This chapter reviews the most recent theoretical impactor work and the latest theoretical efficiency curves. Procedures are then given for using these efficiency curves in the design and evaluation of cascade impactors. Finally, several examples are given comparing theoretical and experimental efficiency curves, pointing out when the theory can be used with great confidence and when the theory should be used only as a guideline.Due to the rather simple principle of operation of an inertial impactor (i.e., the impingement of a jet of particle-laden air on a flat plate) the impactor readily lends itself to theoretical analysis. Three notable works in the early 1950,s were those of Davies and Aylward (1951), Davies et al. (1951), and Ranz and Wong (1952).Davies and Aylward (1951) used a method of conformal mapping to obtain an analytical solution to Euler's equation for the flow of a frictionless fluid through a rectangular impactor. Numerical calculations were then carried out whereby the equations of motion of the particles were solved in a stepwise manner, leading to a determination of the efficiency curves. Since this theory assumed potential flow, the effect of Reynolds numbers on the characteristics of the impactor could not be determined.Ranz and Wong (1952) used an approximate flow field to calculate the efficiency of both round and rectangular nozzle impactors. In the vicinity of the stagnation point, the flow field was assumed to be that of frictionless stagnation flow. Here, the resulting equation of motion for the particles was found to be in a form similar to equations for free vibration with viscous damping. Therefore, the known solutions of the vibration equations were applied directly to the problem and the efficiency curves calculated. This solution technique, however, could not take into account the various geometric variations such as the jet-to-plate distance in the determination of the efficiency curves.The work of Ranz and Wong (1952) was later modified by Mercer and Chow (1968) and Mercer and Stafford (1969) so that the rather simple flow fields of Ranz and Wong (1952) could be used to account for various jet-to-plate distances. The same techniques, however, were used to determine the impactor collection efficiency curves."

Jan 1, 1986

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941

By Margaret R. Egan

A study of the combustion emission products of rigid ventilation ducting was completed by the U.S. Bureau of Mines. The ducting was composed of fiberglass-reinforced polyester resin. Four properties of the ducting were evaluated: (1) propensity to ignite, (2) smoke characteristics, (3) gas emissions, and (4) heat release. Particle sizes, obscuration, optical densities, and production constants for gas and smoke were also calculated. These results provide comprehensive data about the emission products, detectability, and relative hazards of fiberglass-reinforced plastic ducting and other mine combustibles under realistic fire conditions.

Jan 1, 1990

By C. B. Manula

This report is volume 7 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design. Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation," and ventilation. This volume of the final report describes the Rail Haulage subsystem of the Master Design Simulator. This subsystem can be used as a free standing model or can be linked to the Production subsystem to provide rail haulage capability. Complex rail haulage systems can be realistically simulated with this model. This report includes complete instructions for operating the subsystem as well as a program listing. In addition, a case study is included which illustrates the application of the subsystem when linked to the production subsystem.

Jan 1, 1974

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943

By J. H. East

The occurrence of hydrogen sulfide in the gas in solution in the oil produced from the Tensleep sandstone in the Elk Basin oil field in Wyoming constitutes a serious hazard to persons working in, that field. Aware of the general conditions because of petroleum reservoir studies being conducted in that field by its engineers, the Bureau of Mine's willingly agreed to a request of the Petroleum Administration for War to publicize the hazard and the measures for overcoming it. In October 1943 and November 1944, the Bureau of Mines investigated the method's used in handling the oil and in disposing of the hydro¬gen sulfide that occurs with it. This circular reports the results of these observations. HYDROGEN SULFIDE OCCURRENCE IN THE. ELK BASIN OIL FIELD The Elk Basin oil field is in Park County, Wyo., and Carbon County, Mont. It is about 18 miles north of Powell and 12 miles west of Frannie, Wyo. The original Elk Basin oil and gas field was situated in an eroded depression surrounded by an inner rimrock about 200 feet high with a bordering higher plateau about 500 feet above the basin floor.

Jan 1, 1945

By Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications sys tem which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a relatively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurement s of ambient surf ace electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal- to-noise ratio at the surf ace. Numerous C .W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surf ace magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null is the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken Into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

Jan 1, 1974

By R. K. Conrad

The Bureau of Mines conducted corrosion research to determine suitable construction materials for geothermal resource recovery plants. Weight loss, pitting and crevice corrosion, U-bend stress corrosion, and electrochemical polarization measurements were made on selected metals in brine and steam process environments produced from high-enthalpy hypersaline brine from geothermal well Magmamax No. 1 at the Salton Sea Known Geothermal Resources Area, Imperial Valley, Calif. Cadmium (and by extension cadmium coatings) and a 6061-T6 aluminum alloy were unsatisfactory because of high general corrosion rates and, in the case of aluminum, severe pitting Molybdenum and niobium (columbium) were resistant to general corrosion, pitting, and crevice corrosion, Copper alloys corroded at rates that may preclude their use in wellhead brine, The presence of iron accelerated the corrosion of the copper alloys Titanium alloys were resistant to general corrosion and stress corrosion cracking in all of the environments. They exhibited crevice corrosion in some of the brine and steam environments and Ti6A14V pitted in the brine environments. They exhibited passive behavior over a broad range of potentials. Exposure tests were conducted on a high-temperature polyphenylene sulfide thermoplastic (Ryton) in the same environments. A 40-pct-graphite fiber-reinforced Ryton composite deteriorated readily in wellhead brine and failed in all of the brine and steam process environments; Ryton coatings on 316L stainless steel were adherent and performed well.

Jan 1, 1983

By A. B. Cecala

The Bureau of Mines has developed a pallet loading dust control system designed to lower the dust exposure of workers during the bag stacking process at mineral processing facilities. The system makes bag stacking much easier because the pallet height remains constant throughout the entire bag stacking cycle through the use of a hydraulic lift table. The system uses a push-pull ventilation technique to capture the dust generated during bag stacking. A low-volume, high-velocity blower system operating at approximately 150 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-in air jets (approximately 1,200-ftjmin velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they entrain the dust generated during bag stacking. The exhaust ventilation system pulls approximately 2,500 cfm of air and dust through the exhaust hood. This exhaust air can then be dumped into a baghouse ventilation system, or filtered before being discharged outside the mill. During a laboratory evaluation, a 70-pct dust reduction was recorded for the bag stacker. The system was then evaluated in an actual working environment. The first field evaluation was performed at a silica sand operation in which one worker performed the entire loading and bag stacking process. This worker's dust exposure was lowered 76 pet when using the new pallet loading system. The second field evaluation showed only moderate dust reduction, but this was mainly attributed to an overriding problem associated with background dust and the cleanliness of the bags. From both the ergonomic and production standpoint, the system was well received by both the workforce and plant management.

Jan 1, 1988