Search Documents

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By C. G. Kirkpatrick

Analysis of the data produced by a wide-band, sensitive, horizontal, biaxial motion sensor has revealed several distinctive patterns before, during, and after a roof fall. The signals prior to the roof fall are similar in spectra, but one thousand times larger in amplitude, than those after the roof fall. Immediately preceding the roof fall, by two to twelve hours, five events occurred which were larger in amplitude and lower in frequency than even the large pre-roof fall background signals. An interpretation of these events is offered.

Jan 1, 1979

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By F. P. Haver

Because State and Federal agencies have limited the amount of sulfur oxides that can be discharged to the atmosphere, most copper smelters plan to convert the S02 in offgases to sulfuric acid. In some cases, however, it might be preferable to use a nonsmelting method to fix the sulfur in the form of a discardable product. Research by the Federal Bureau of Mines has shown that sulfur in copper concentrate can be converted into insoluble anhydrite (CaS04) by roasting the concentrate with lime (CaO). After leaching the calcine to recover metal values, the residue may be discarded without harm to the environment. The process can use a rougher flotation product, thus reducing separation costs and saving valuable minerals (for example, molybdenite) that are now lost in making cleaner concentrate. In tests, rougher concentrate was pelletized with the theoretical amount of lime and roasted for 1 hour in a 6-1/2-inch-ID by 11-foot-long rotary kiln at 700° C. Sulfur retention was about 97 percent. Leaching the calcine with 20 percent RCI extracted approximately 99 percent of the copper, 73 percent of the iron, and 91 percent of the molybdenum. After the molybdenum was removed from the leach solution by adsorption on activated carbon, copper with a purity in excess of 99 percent was obtained by cementation on sponge iron. The strip solution then could be spray-roasted at 500° C to recover the RCI for recycle and obtain F2O3 as a byproduct.

Jan 1, 1975

By M. J. Spendlove, P. P. Zapponi

"INTRODUCTION In carbothermic processes for the production of magnesium, magnesium oxide is reduced by carbon according to the following equation:(1) MgO + C = Mg(g) + CO.The reaction is virtually complete at temperatures above 2,000° C. but reverses rapidly at somewhat lower temperatures. To produce magnesium by this reaction, therefore, it is necessary to cool the gas very rapidly to a temperature at which the rate of the reverse reaction becomes negligible. Several media for quenching the gas have been proposed, among which are hydrogen, natural gas, liquid hydrocarbons, and molten metals of low melting point.The results of a preliminary investigation on the use of molten lead as the quenching medium are summarized in this report. The work was done in 1941, when the threat of war made it imperative to investigate every process that offered possibilities for rapid expansion of domestic production of magnesium. Although the results were encouraging, other processes appeared to offer better prospects for immediate wartime development, so the work was not continued. Shortly before the investigation was completed, several patents on the use of low-melting metals for absorption of magnesium vapors appeared, 4/"

Jun 1, 1947

By Joseph M. Kurtak

The U.S Bureau of Mines conducted a five-year mineral resource assessment of the 16.6 million acre Colville Mining District in northern Alaska, which includes part of the National Petroleum Reserve in Alaska. The study was initiated at the request of the Bureau of Land Management, which administers the majority of the region. The study was done in cooperation with the Alaskan Division of Geological and Geophysical Surveys, the U. S. Geological Survey, and the University of Alaska. During fieldwork, 1593 rock, soil, and stream sediment samples were collected and four bulk samples taken for beneficiation studies. A total of 40 mineral occurrences were documented, including 27 which were previously undescribed. No mining has occurred within the district. Mississippian carbonaceous shale and siliceous mudstone contain stratiform exhalative lead-zinc-silver occurrences. Grades average 8.0% combined lead/zinc and 51 gm/mt silver. Upper Devonian to Lower Mississippian sandstones host breccia veins, containing up to 29% combined lead/zinc and 274 gm/mt silver. Mineralized quartzites of similar age have potential for disseminated-type lead-zinc deposits. Samples from Lower Cretaceous mudstone and shale beds up to 6.5 meters thick, contain as much up to 12% manganese. Upper Mississippian carbonaceous shale and limestone beds contain up to 23% phosphate. Stratiform barite deposits hosted by cherts, are up to 27 meters thick with an average specific gravity of 4.16. Vein-type fluorite occurrences are associated with Mississippian limestone. Moderate potential exists for development of zinc -lead-silver, barite, and phosphate deposits.

Jan 1, 2011

By Lulie H. Crump

Salient historical data on consumption of fuels and energy have been summarized by State and census district for the years 1960 through 1972. This Information Circular covers States west of the Mississippi, and Information Circular 8704 covers States east of the Mississippi. These data replace previously published compilations of energy consumption statistics by States and districts. Future annual studies are planned using the same Btu conversion factors applied in these two Information Circulars.

Jan 1, 1976

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By J. Koster

[In lQ jG thc E'lcct,ro:~(: L7.l :~u..-ic:ll S;%cti ?n of t?c :I. tcIl~tr,-;lcal 3:vi cioa, ?U~CE~U of lv!irtos, bc,~m an 9.ct iv.t In-:?*t ik7;5i GI of r.:ct.l-;c?;is for rccovcrin,; niclrel, cop?ir, an2 ?? cciou:; ~ot-1 c 1;-on or; :; of tile 3unl~crvi~.l~~ tiistrict in C1ni.k Coult:r, !Icl.r. ]

Jan 1, 1939

By I. L. Nichols

Volatilization of cesium from pollucite ore was investigated as an initial step in the production of purified cesium metal or cesium salts. High recovery of cesium and rubidium as chloride sublimates was accomplished by 2-hour roasts in a tube furnace using charges containing 1 part ore, 2 parts limestone, and 0.23 part calcium chloride. Recoveries of cesium in the sublimate product were 89.1, 92.9, and 95.2 pct, respectively, using 1,100° C and vacuum, 1,250° C with an air sweep, and 1,250° C without an air sweep. Most of the lithium, sodium, and potassium sublimed with the cesium and rubidium, but virtually none of the calcium, aluminum, and silicon in the charges was volatilized.

Jan 1, 1966

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By B. W. Gandrud

This is the first report published by the Bureau of Mines on washability characteristics of coal from beds in Tennessee. It is based principally upon screen-sizing and float-and-sink tests of raw coal from a bed on the Cumberland Plateau. Stripping operations were undertaken recently on this bed by the Cumberland Collieries, Inc., near Chalybeate,Van Buren County, Tenn. The bed has not been definitely correlated, but it may be an extension of the Sewanee bed, which has been mined extensively in the Tracy City district to the south-vest and at points near Dunlap and Pikeville to the southeast and east. It was spoken of by officials of the Cumberland Collieries as the Sewanee bed at the time of sampling for this study. In a letter dated October 16, 1948, W. D. Hardeman, geologist of the Department of Conservation, Nashville, Tenn., states: "The stripping operations of the Cumberland Collieries near the old postoffice at Chalybeate are, I am fairly certain, in the upper part of the Whitwell shale, which carries the Sewanee coal. This coal may be a stray seam, but it probably can be correlated with the Sewanee coal, which is mined farther east. "There are no detailed geologic maps or reports covering the area, and this opinion is based on what was observed in visiting the strip mines in that general vicinity." The laboratory work upon which this report is based was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the Cumberland Collieries, Inc.

Jan 1, 1949

By Charles A. R. Lambly

This paper, which describes the mining practices of the Pend Oreille Mines & Metals Co. at Metaline Falls, Wash., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. ACKNOWLEDGMENTS Acknowledgment is made to L. P. Larson, president, and Jens Jensen, secretary, of the Pend Oreille Mines & Metals Co. for permission to publish this paper. information was supplied by E. Berglund, mine superintendent; Earl Miller, chief engineer; Lynn Kinney, John Currie, and Wally Frick, engineers; Arthur Newman, chief clerk; and Jack Crampton, assayer.

Jan 1, 1941

By W. A. Selvig

[THE BUREAU OF MINES receives many requests for information regarding the low-temperature carbonization properties of American coals. This report presents in collected form the results of Fischer-Schrader bench-scale, low-temperature carbonization assays at 500° C. made by the Chemistry and Physics Section at the Pittsburgh station of the Bureau of Mines. Most of the assays were made of coals tested in connection with a survey of gas and coke-making properties of American coals,4 which was started in 1928 by the Bureau in cooperation with the American Gas Association. Other coals were assayed in connection with miscellaneous investigations. Since 1930 about 400 samples of coal were assayed from nearly every coal-producing State, Alaska, and British Columbia, Canada. The results of the tests on about two-thirds of the coals are scattered through more than 50 separate publications. This paper summarizes the data in the published reports as well as all unpublished data obtained to January 1, 1956. The report also includes a detailed description of the procedure used in making the assay.]

Jan 1, 1957

By K. F. Anderson

The increasing number of oil-productive reservoirs in the Ellenburger formation has emphasized the need for information pertaining to the hydrocarbon recoveries that may be obtained from such reservoirs. Most of the space available for accumulating hydrocarbons in the Ellenburger formation is derived from fractures, which makes it difficult to estimate reserves or probable recoveries. The Ellenburger reservoir in the Big Lake field was selected for study because it is one of the few near-depleted reservoirs in the area. The experience gained in operating and developing this reservoir has been and should continue to be a helpful guide to operators both in predicting recovery and establishing methods of development and operation In similar reservoirs. Development and production data were gathered from different sources. The writers have compiled and interpreted these data to estimate the ultimate recovery of hydrocarbons. In addition to the estimates of ultimate recovery, the report contains sample calculations and estimates of theoretical recovery based on different methods of operation. The calculations presented in this report indicate that the Ellenburger reservoir is 95 percent depleted and that the ultimate recovery of hydrocarbon liquid from the oil reservoir and gas cap combined will he 4-0 barrels per gross acre-foot of reservoir rock. An estimated 32 barrels of condensate per gross acre-foot of reservoir rock in the gas cap has been recovered, and the estimated ultimate recovery of crude oil will be 47 barrels per gross acre-.foot of rock in the crude-oil reservoir.

Jan 1, 1954

By Cliff McCartney, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research to evaluate and improve remote mine seal construction technology for mine fire control and suppression. The main focus of this work is to develop reliable technology that will remotely seal a mine opening from floor-to-roof and rib-to-rib. NIOSH, in partnership with Strata Mine Services Inc.1, is evaluating the capability of a two-component phenolic foam-based product, called Rocsil®1, that is intended for cavity filling, air and gas sealing, and consolidation of highly fractured strata. Rocsil® can be rapidly applied, has a quick cure time, a high expansion rate, good compressive resistance and excellent anti-static properties. When the resin and catalyst are mixed, an immediate foaming reaction occurs followed by rapid expansion up to 30 times the original volume. By virtue of its fire-resistance properties, Rocsil® foam has application for sealing underground mine areas undergoing heating from spontaneous combustion and it could be useful for remote mine seal construction to aid in mine fire control and suppression. This paper presents an overview of remote mine sealing technology, introduces the use of Rocsil® foam for remote mine seal installations, offers a case study of the use of this rigid foam material to remotely construct a temporary in-mine seal and discusses technology improvements. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.