Search Documents

By John C. Edwards

The Bureau of Mines has developed a time-dependent mathematical model of radiative heating of bulkheads in mines. The model includes both reradiation from the duct (cylindrical) walls and direct radiation from the fire zone. Thermal loss into the wall of the duct and into the bulkhead is included. Both brick and wood bulkheads are considered. It is found that the heating rate of the system scales as the duct length-to-diameter ratio and the flame temperature. In particular, the time required for the irradiated surface of the bulkhead to reach a specified temperature decreases with increasing flame temperature for a fixed length-to-diameter ratio and increases with increasing length-to-diameter ratio for a specified flame temperature. It is also deter-mined that the time, T, for the bulkhead surface temperature to reach a specific value, Tb, for a fixed length-to-diameter ratio less than 4 and for a flame temperature of 1,200 K is approximately linearly dependent on Tb for 500 K < Tb < 700 K, and is nearly exponentially dependent on the length-to-diameter ratio for Tb = 600 and 700 K.

Jan 1, 1979

By F. A. Skirvin

Purification techniques were investigated for removing low-level metallic impurities from tungsten hexachloride. These techniques included distillation) fused-salt scrubbing) zone refining) and adsorption. Fractional distillation of tungsten hexachloride was found to be an effective purification method. The impurity levels of molybdenum) iron) nickel) copper) magnesium) and manganese were reduced to provide a tungsten halide sample which contained a total of less than 10 ppm detectable metallic impurities. Purification by fused-salt scrubbing of tungsten hexachloride in a lithium chloride-potassium chloride eutectic produced a hexachloride product which was of approximately the same quality as that obtained by distillation. Zone refining and adsorption did not appear to be as effective as distillation or fused-salt scrubbing.

Jan 1, 1967

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

The National Institute for Occupational Safety and Health (NIOSH) recommends that occupational exposures to respirable coal mine dust and respirable crystalline silica* be controlled by complying with the provisions presented in this document. These recommendations are designed to protect the health and provide for the safety of workers exposed to respirable coal mine dust and respirable crystalline silica for up to 10 hr/day during a 40-hr workweek over a working lifetime. The information presented in this document demonstrates that underground and surface coal miners are at risk of developing simple coal workers&apos; pneumoconiosis (CWP), progressive massive fibrosis (PMF), silicosis, and chronic obstructive pulmonary disease (COPD). Adherence to the recommendations in this document should prevent or greatly reduce the risk of adverse health effects in workers exposed to respirable coal mine dust and respirable crystalline silica. NIOSH recommends that preventive efforts be focused primarily on reducing worker exposures. Effective health and hazard surveillance and medical screening are also useful components of a comprehensive prevention effort.

Jan 1, 1997

To clean coal mine air by developing a low-cost scrubber suitable for belt transfer and similar applications. Approach Design a scrubber operated by water only, with no moving parts. Use conventional water spray nozzles located within a duct to both move and clean the air. Use a droplet eliminator to get the water droplets and mist back out of the airstream. How It Works Conventional scrubbers require a mechanical fan driven by either an electric or a hydraulic motor. They also require water sprays and some type of scrubbing mechanism. The water powered scrubber, however, offers higher reliability over conventional scrubbers since it utilizes the water sprays to both move the air and scrub the particulate from the air. Conventional water spray nozzles are placed near one end of a rectangular duct open at both ends. The sprays are directed towards the far end of the duct where a stationary wave blade water droplet eliminator is located. Movement of the water spray droplets coming from the nozzles generates (by momentum transfer) an air movement In the same direction as the sprays. The volume of air moved Is primarily a function of the duct cross-section size, water pressure and water

Jan 1, 1981

By Frank Pilotte

Proper design characteristics for a seismic system to locate miners during a mine disaster are considered in terms of a total system concept. Field hardware, processing equipment, operating personnel, deployment, training, and supportive R and D are necessary elements of the total system. Each of these elements is discussed and an indication given as to the requirements necessitated by each one. Hardware must be portable, rugged, and fieldworthy. Processing equipment must be simple to operate, expandable for future processing improvements, and ruggedized for field use. A small well-trained team must be available for quick response in times of emergency. Alternative deployment procedures are necessary to allow for a variety of situations including both ground and air delivery. Supportive R and D is used to support training and upgrading of the system.

Jan 1, 1974

By J. T. Dunham

The Bureau of Mines studied by dilatometry the effect of titanium on the thermal expansivity of hot-rolled zinc and Zn-l percent Cu alloy. The titanium content of the alloys was varied up to 0.3 percent. Expansion coefficients were determined from measurements made both parallel and perpendicular to the plane of the rolled sheet. Titanium reduced expansion parallel to the plane of the sheet, especially in the rolling direction, but increased expansion perpendicular to the sheet. Basal-plane pole figures showed that the degree of preferred orientation increased with the titanium content in the alloy, and that anisotropic expansion can be correlated to sheet texture.

Jan 1, 1965

By Richard L. Rains

In 1984 and 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 162,887-acre Mormon Mountains Wilderness Study Area (NV-050-161) in order to evaluate its identified mineral resources. The study area is located in Lincoln County, NV, about 60 miles northeast of Las Vegas. The study area had no mines or mining claims in 1985, and no mineral resources were identified within the study area, or at the Whitmore mine or Iron Blossom prospect near the study area. The alluvial fans around the southern boundary are staked with about 450 placer claims. Chemical analyses of samples indicate that some limestone in the study area is suitable for manufacturing cement or for agricultural purposes but the limestone is distant from markets and therefore not economic in the foreseeable future. The study area is blanketed with oil and gas leases, but no known productive horizons were identified.

Jan 1, 1986

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By Edward F. Divers

Tills U.S. Bureau of Mines report briefly evaluates the advantages and disadvantages of basic dust control techniques presently used by U.S. coal preparation and mineral processing plants. These include ventilation, baghouse-type collectors, wet scrubbers, electrostatic precipitators, source control, sprays, good housekeeping, and personal protection devices. Two specific problems in these types of operations are also considered: dust collector system duct clogging, and control room dust control. Information provided in this report results from dust control research projects conducted by the Bureau at various coal preparation and mineral processing plants over the past decade to reduce workers&apos; dust exposure. These studies indicate that plant ventilation systems normally provide the most cost effective method for dust control. Baghouses and scrubbers were also effective in specific applications, and examples of each are given. In extreme dust conditions, personal protection devices, such as respirators or the dust helmet, can also be highly cost effective.

Jan 1, 1990

By O. M. Bishop

"SUMMARYAs a result of the increased demand for fluorspar during the war, the Bureau of Mines investigated numerous fluorspar properties in the southern Illinois field, which is centered in Rosiclare. Among these the J. J. Shelby 40-acre tract on the western edge of the district presented favorable factors that caused it to be chosen /or exploration.H. G. Spiller, formen lessee of the property, had explored the Shelby vein by means of an adit level and winze, and showed it to contain goad values in zinc and fluorspar at the depth explored. A diamond-drill hole with which Spiller explored the vein 78 feet southwest of the winze, however, failed to cut ore. After studying the field evidence, the Bureau concluded that the vein merited further exploration, particularly at a depth of about 440 feet, where the Fredonia limestone would form the foot-wall of the vein and the hanging wall would be the competent Cypress sandstone.Between October 17, 1944, and March 26, 1945, three diamond-drill holes were bored for a total inclined depth of 1,592 feet. Holes 1 and spaced approximately 500 feet apart, explored the vein at 440 feet 4 below the surface. The economic mineralization existed in the vein where cut. Hole 3 cut the fault at approximately 300 feet below the outcrop but failed to find any vein matter except stringers of calcite with small amounts of pyrite."

Apr 1, 1947

By Thomas J. Peters

In 1978, the U.S. Bureau of Mines and the U.S. Geological Survey completed a joint mineral survey of the Chemise Mountain and King Range study areas as mandated by the Federal Land Policy and Management Act of 1916, Public Law 94-579. The U.S. Bureau of Mines examined all identified mineral prospects and deposits; the results of these examinations are included in this report. The U.S. Geological Survey studied the regional geology, geochemistry, and geophysics; the results of these studies are available in USGS Map MF-1196. No mineral resources were identified in either the Chemise Mountain or King Range study areas; however, a high-grade silver and base-metal occurrence, and minor manganese resources were identified in between the two study areas, within the King Range Conservation Area. The only mining activity in either area was a placer gold prospect on Honeydew creek in the northeastern part of the King Range study area. Three samples from this prospect contained no gold. The Chemise Mountain and King Range study areas are in a mountainous region along the coast of northern California, 230 road miles north of San Francisco, and 70 miles south of Eureka by way of U.S. Highway 101, through Garberville and Redway. The Chemise Mountain study area consists of 3,941 acres; it includes the 2,598-ft Chemise Mountain, and the cliff-lined seacoast southeast of Shelter Cove. a resort and fishing village. The King Range study area consists of 39.764 acres northwest of Shelter Cove, and includes the northwest-trending King Range with elevations above 4,000 ft. The Chemise and King Range study areas are underlain by deep-water marine sandstones, shales, and minor pillow basalts of the Late Cretaceous and early Tertiary Franciscan Subduction Complex. Mineral production was 1,650 tons of manganese ore within a manganiferous bed overlying pillow basalt at the Queen Peak mine southeast of the King Range study area. However, no significant manganese resources were found in the Queen Peak area. The Point Delgada area, directly south of the King Range study area, has prospects with high grade copper, lead. silver, and zinc. Exposures are inadequate to estimate resources; however, the metals may be associated with Franciscan volcanism (volcanogenic). The Chemise and King Range study areas may contain similar economic silver-rich, base-metal deposits.

Jan 1, 1992

By Robert H. Peters

Several significant problems associated with employee turnover among underground miners are described in this Bureau of Mines report. Although a vast amount of research has been conducted on turnover among employees in nonmining industries, there has never been an attempt to empirically investigate the causes of turnover among underground miners. This report presents the results of empirical research on employee turnover in other industries and describes and critiques the research methods that have been used to investigate turnover. Using the findings on employee turnover in other industries and known data about miners and the mining industry, a conceptual model of the factors that cause turnover among miners was generated. This model, which is expected to provide a basis for later empirical studies, is presented. Several recommendations for controlling miner turnover are also presented.

Jan 1, 1986

By S. Benedict Levin

The Big mine has been a source of mica and high-grade felspar from separate zones in the same pegmatite dike since 1914. In 1943 it became the outstanding producer of strategic mica in New England. The urgent need for sheet mica led to core-drilling by the Bureau of Mines from February to May 1914. Nine diamond-drill hob&apos;s aggregating 1,474 feet in length were drilled by the Bureau of Mines with the objective of developing extensions of the known mica shoots. The use of large-diameter bits made it feasible to obtain reasonably reliable results in diamond-drilling this type of deposit.

Jan 1, 1949

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By T. M. Garland

A nomographical approach is proposed as a fast, easy-to-use, and reason- ably accurate method for estimating expected discounted cash flow (DCF) rate of return and payout time for onshore development drilling and oil production. All costs pertaining to drilling, completing, and equipping development wells, annual expenses of operation, maintenance, and taxes incurred in producing properties, and crude oil prices were considered in developing the nomographs. This report briefly outlines the origin, derivation, and use of the nomographs.

Jan 1, 1973

By G. L. Humphrey

Although thermodynamic data for ferrous oxide are among the most important in extractive metallurgy, adequate values have not been available until quite recently. The older data suffered not only from the usual experimental difficulties but especially from lack of the knowledge that ferrous oxide of stoichiometrical composition does not exist as a single, thermodynamically stable crystalline phase under any circumstances. This paper reports new experimental data on the heat of formation of ferrous oxide by two methods (combustion calorimetry and solution calorimetry), employing material of unequivocal composition. The results are compared with values obtained from data for the hydrogen reduction, carbon monoxide reduction, and disproportionation reactions of ferrous oxide, and a best value is selected. A table of heat and free energy of formation values of ferrous oxide to 2,000°K is given. These values are combined with available data for water, carbon monoxide, and carbon dioxide to obtain theoretical heats and free energies of reduction corresponding to the selected heat of formation. Hydrogen and carbon monoxide reduction equilibria are compared, and the differences in trend with temperature and the percentage utilization of the reductants are considered.

Jan 1, 1952

By F. R. Cattoir

This Bureau of Mines study investigated molten salt electrorefining for beneficiating low-grade, high-carbon ferrochromium products which can be readily produced from domestic chromite concentrates. A second objective was to refine commercial ferrochromium into low-iron chromium products. Electrorefining of both types of ferrochromium in molten CaC12-NaCl-CrC12, CaCl2-MgC12-CrCl2, or KC1-LiCl-CrCl2 electrolytes produced chromium-iron products with virtual elimination of other impurity elements and some lowering of the iron content, Over 90 percent of the chromium present in the feed materials was recovered. The electrodeposited products were upgraded further by magnetic separation techniques into chromium containing less than 5 percent iron. The technical feasibility of preparing a premium chromium product from a low-grade, high-carbon ferrochromium made from domestic chromite was demonstrated. Chromium virtually free of carbon, oxygen, and silicon from high-carbon ferrochromiums was produced. In addition, the amenability of three commercial grades of ferrochromium to electrorefining and magnetic separation for preparing chromium metal containing less than 5 percent iron was determined.

Jan 1, 1969

By Robert M. Strong

The following report is a summary of the commercial results which 'Were obtained from 2,000 tests conducted by the technologic branch of the United States Geological Survey at St. Louis, Mo., and Norfolk, Va., in 1907 and 1908, under the technical supervision of R. H. Fernald, engineer in charge of the producer-gas section. The tests dealt primarily with gasoline, forming part of the investigation of mineral fuels provided for by acts of Congress. To determine the relative economy and efficiency of gasoline it was compared with denatured alcohol. The tests, many of which were undertaken in connection with work for the Navy Department, supplemented, to a certain extent, the work of previous investigations, but only so far as was necessary to emphasize some of the more important points and to lead up to the defining of conditions required for the economical use of gasoline and alcohol. In order to determine and eliminate the affecting engine conditions as far as possible, the investigation was commenced by making comparative gasoline and alcohol tests on the same engines. These tests were repeated on other engines of approxiElately the same size and speed, having different degrees of comFression, different methods of governing, and different carburetors. The final report will include much material that may be of use in engine design, but that side of the investigation was not pursued any further than was necessary to obtain the best possible results, for alcohol and for gasoline with the engines at hand, and to prove that the minimum fu·el-consumption rate for each could be obtained in approximately the same manner. The effects of engine and of operating conditions both have a bearing on the commercial deductions but will be discussed only in a general way at this time.

Jan 1, 1911