Search Documents

By Laurence A. Dahners

As part of the strategic minerals program, the Bureau of Mines conducted a diamond-drilling project on three barite properties in eastern Tennessee and western North Carolina during the summer and fall of 1944. These properties, the Moccasin Gap prospect and the Krebs property in Cocke County, Tenn., and the Sandy Bottom mine of the Stackhouse group in Madison County, N. C. (fig. 1), are known to have produced some barite. The Bureau of' Mines project was planned to prospect for extensions of the ore bodies. A total of 3,169 feet of diamond drilling was done in 15 holes on the three properties. Tabulations of sample analyses and drill-hole logs are presented in this report. Two other mines of interest in the area are the McCoy and the Williams in Cocke County, Tenn. The Williams adjoins the Krebs. No drilling was done by the bureau in either of these properties.

Jan 1, 1949

By Jr. Sayre

Results of studies of reservoir and wax-precipitation temperatures relating to wax deposition in the reservoir of the Bradford oil field are presented in this report. During 1949 and 1950 Bureau of Mines engineers made temperature measurements in 42 wells, which indicate that the Bradford Third-sand temperatures range from 59.7° F., at 1,150 feet, to 71.9° F., at 2,040 feet. Reservoir temperatures measured at the same depths in newly drilled wells and oil-producing wells differed as much as 4.5u F. Injection-well temperatures measured during water injection showed that the temperature of the water entering the sand was 11.5° F. lower than reservoir temperatures before injection. The cooling in the formation resulting froth the injection of low-temperature water was 11.5° F. in the vicinity of the injection-well bore, and a maximum of 2.1° F. 200 feet from the injection well. Sand temperature, after 5 months of water injection, was reduced 1.5° F. 90 feet from water-injection wells. The temperature at which wax begins to precipitate from solution in crude oil was determined at atmospheric pressure for 26 samples and ranged from 51° to 67° F. Oil samples from wells producing no water had wax-precipitation temperatures ranging from 51° to 58° F. and wax contents from 2.20 to 2.97 weight percent, whereas the samples from wells producing water and oil had wax precipitation temperatures ranging from 580 to 67° F. and wax contents from 2.57 to 3.42 weight percent .

Jan 1, 1952

By J. B. F. Champlin

The continuing development of the nuclear industry in the United States requires a program of waste disposal that insures against the release of large amounts of radioactivity to the environment. This paper describes research on one proposed means of disposal of this waste, that of injection into geologic formations at depth. Nuclear production plant wastes were simulated and injected into samples of sedimentary rock obtained from outcrops, quarries, and deep wells. Changes in the chemical and physical characteristics of the rocks caused by the interaction of ions and suspended particles in the waste solutions with the cementing material and claylike particles in the rock are discussed. Laboratory tests show that nuclear wastes can be injected into many natural porous, permeable geologic formations. Injectivity can be maintained over a longer period by monitoring the ionic balance and particle-size distribution of waste streams. The combination of permeability and porosity with low cation-retention capacity, as exhibited by most sandstones, would satisfy the engineering requirements for the subsurface disposal of nuclear waste. Shales and clays with their low permeability and high cation-retention capacity would make excellent confining formations. The amount of cation retained by sedimentary rocks increases with increasing valence or concentration of the cation or decreasing brine concentration. The use of rock cores as model reservoirs had proved successful in determining some of the parameters that need to be considered in full-scale field disposal of wastes.

Jan 1, 1967

Construction workers may be exposed to hazardous dust containing silica when working in enclosed cabs during construction activities. The National Institute for Occupational Safety and Health (NIOSH) found that equipment operator exposure could be reduced by retrofitting air pressurization and filtration systems on existing cabs, using sweeping compounds on soiled floors, and implementing a dust control program.

Jan 1, 2009

By J. W. Paul

Withdrawing timber in coal mines is done for the purpose of inducing the roof to cave in the mined-out areas and thereby relieve stresses in the immediate roof material over the working places adjacent to the breakline of the roof, thus preventing the crushing of the ends of pillars and adding to the safety of those engaged in pillar extraction. A secondary purpose is the recovery of timber for further use either as prop-, crossbars, lagging, sprags or cap pieces. At some mines timber is withdrawn as a precaution against fire which may he of spontaneous origin, because wood always aids a fire of any origin. With some of the power-driven types of machines now in use a greater proportion of mine timber may be recovered, and in mines where pillars are left too narrow for their removal some of the timber in rooms might be salvaged for further use.

Jan 1, 1933

By C. W. Davis

Before listing the laboratories and the work performed there, it is proper to make clear what is done and what is not done by Federal bureaus, States, and Territories, as well as by countries to the north and south of the United States. FEDERAL Bureau of Mines. - The Bureau of Mines does not make assays or analyses for individuals or firms unless the samples are part of the ore-testing and ore-dressing investigations of the Metallurgical Division on representative ores from mining districts and of possible benefit to the entire mineral industry through published reports. All significant results obtained in this way are made public. Any mineral sample sent to this Bureau for simple identification will be examined.

Jan 1, 1938

By J. D. Zetterstrom

This report supplements an earlier publication on lightweight aggregates of North and South Dakota.3/ The purpose of the investigation was (1) to study the expansion characteristics of large samples of Dakota clays and shales in a 12-inch by 15-foot rotary kiln; and (2) to improve the laboratory bloating test as a tool for predicting the suitability of samples for the rotary-kiln process. This was done by comparing results of the laboratory and kiln tests.

Jan 1, 1956

By A. L. Engel

Simple treatment methods, employing the least possible equipment, can sometimes be established for marginal ores and economical results achieved. In continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno Station of the Bureau of Mines, typical ores from newly discovered or recently explored mining districts have been investigated. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores, as well as the conservation and recovery of values in products from former operations that were discarded because of past inability to treat them economically. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas some involved samples of old dumps or tailings piles. The test, work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials; and because, inasmuch as the samples were representative of the districts from which they were obtained, this in-formation should be helpful in the future development of these districts. The present report is a compilation of results of brief preliminary tests on oxide ores only, which contained gold and silver and in some cases base metals. The methods of treatment used include gravity concentration, amalgamation, flotation, and cyanidation. For the most part, only standard laboratory procedures were employed. No attempts were made to develop new methods for the low-grade refractory ores in this group of samples if simple treatment was not successful, as the stage of development of the properties did not warrant extensive experimentation on the samples submitted.

Jan 1, 1951

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By O. C. Blade

A summary of the characteristics of motor gasoline for the winter 1951-52 is presented in table I, and for comparison, a similar summary for the winter 1950-51 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. The results of this survey show that octane numbers have risen slightly since the summer of 1951 but are below the record levels of the winter of 1950-51. The fractions of a unit change since the summer preceding have resulted in the research and motor-method octane values being virtually the same as the figures for the survey of summer 1950. In volatility characteristics the winter gasolines have changed very little. Average Reid vapor pressures are 10.5 pounds for both grades of fuel compared to 10.4 and 10.5 pounds for premium and regular-price gasolines, respectively, of the winter of 1950-51.

Jan 1, 1952

By Leonard Obert

THE CRACKING AND POPPING of rock, often heard by men working underground, for years has been interpreted as a warning of danger and unstable ground. However, not until 1939 was it discovered that rock under stress generates subaudible and sometimes audible seismic disturbances (referred to as "micro-seismims" 4), which can be detected with the use of a suitable seismic apparatus. Since that date laboratory and field investigations have been in progress to ascertain to what extent this phenomenon can be utilized to detect, localize, and determine the magnitude of areas of instability in and around mine openings and to predict if and when failure will occur. These investigations have included a determination of the types of problems to which the method is applicable and the effect of rock type, geological defects, such as joints, fractures, faults, and other uncontrollable factors, on the reliability of results. Six reports have been prepared covering the investigations conducted between 1940 and 1952 (4-9). 5 These reports describe some of the characteristics of micro-seismims, as determined from both laboratory and field tests; the equipment used to pick up and record micro-seismims; the general test procedure and method of analyzing results; and applications of the method to specific mining problems.

Jan 1, 1957

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By H. Kenworthy

A zinc-pyrite ore from the Gray deposit in Jo Daviess County, Ill., was successfully concentrated on a laboratory scale. Initially, drill cuttings were submitted for separation of zinc and iron concentrates. Subsequent to mine development, a large sample of coarse ore was submitted to ascertain its amenability to sink-float treatment to produce a low-grade zinc-iron concentrate and discard a clean tailing. The samples of ore were submitted to the Rolla Metallurgical Branch by the Mining Division of the Federal-Bureau-of Mines. They were obtained during the recent war as a part of the extensive government program to increase metal production through exploration for new mineral deposits and investigation of old mineralized areas. The first sample consisted of about 3,000 pounds of drill cuttings collected, during the Bureau?s churn and diamond- drilling program. The second sample was taken at a later date, after Tri-State Zinc, Inc., had opened the deposit and commenced milling the ore. This sample consisted of a ?ton-of mill feed crushed through 2 inches and collected over a period of 3 days.

Jan 1, 1949

By Ren G. Dong, Jay Kim, Daniel E. Welcome, Won Joon Song, Charles Hayden

Prolonged, extensive exposure to hand-transmitted vibration could cause a series of vibration-induced disorders in the vascular, sensorineural, and musculoskeletal structures of the human hand-arm system, which have been collectively called hand-arm vibration syndrome (HAVS).1 To assess the risk of HAVS the international standard ISO 5349-1 (2001)1 recommends using the root-mean-square (rms) acceleration of the measured vibration with a frequency weighting. While a few epidemiological studies have reported results consistent with the predictions made according to the recommendation, many other studies have reported results with large discrepancies.2 This may be partially attributed to the time-averaging effect involved in calculation of the frequency components, especially for impact type tools. Because the spectral characteristics of impact tools change dramatically with time, a time-frequency (T-F) analysis can provide better characterizations of such highly transient vibrations. The analytic wavelet transform (AWT) is an ideal T-F analysis tool because it possesses the advantages of both the Fourier transform and the wavelet transform.3 The objective of this study was to explore the application of the AWT method for characterizing the impact tool vibrations and assessing their exposure risk. Methods Five tools (two chipping hammers, two riveting hammers, and one concrete cutting saw) were used in this study. The saw vibration was measured when it was used to cut a section of road pavement during a repair. The vibrations on the other tools were measured by the procedure specified in ISO 8662-2 (1992).4 A sampling rate of 16,386 Hz was used in the measurement. The AWT and Fourier analysis were applied to these signals and to identify their characteristics. Results Figure 1 compares the T-F characteristics of the accelerations measured from the relatively steady concrete saw and a riveting hammer. The frequency weighting specified in ISO 5349-11 was applied in the calculations. The comparison clearly shows that the two tools have completely different T-F characteristics.

Jan 6, 2006

By A. B. Hooker, Iilsley. L. C.

"Flame safety lamps have been used for about one hundred years in coal mines where a dangerous accumulation of explosive mine gas (methane) might occur and thus render the use of ordinary unprotected flame lamps dangerous. Flame safety lamps are not only used for illumination, but also for detecting the presence of dangerous percentages of methane mixed in the air of the mine.The safety of the lamp depends chiefly upon the cooling qualities ofThe safety of the lamp depends chiefly upon the cooling qualities of the wire gauze used to permit free circulation of the air through the lamp. If one enters a part of the mine where methane is present in the air, the methane enters the lamp and coming in contact with the wick flame is ignited and continues to burn within the gauze without igniting the methane surrounding the lamp. If the air within the mine is traveling at a velocity of several hundred feet per minute the burning gases may be driven through the gauze by the air current. If the gauzes are properly designed and of the proper material, these burning gases will be so cooled as they pass through the gauze that they will not cause an ignition of the gas surrounding the lamp. In order to test the effectiveness of a given safety lamp, tests are made in moving explosive mixtures of gas and air arranged to simulate mine conditions.The Bureau of Mines investigated many features relative to the safety of flame lamps and in 1915 established an official schedule known as Schedule 7 whereby flame lamps having certain prescribed qualifications would be approved as permissible for use in gaseous mines."

May 1, 1920

By W. E. Lamont, R. E. Perry, I. L. Feld

The Bureau of Mines conducted research to determine the conditions required to sinter a pyrrhotite calcine into a product suitable for iron blast furnace feed . The calcine , a fine - grained iron oxide produced by roasting sulfide flotation concentrate , analyzed about 60 percent iron and 1 percent sulfur . Sintering of the calcine without prior pelletization was not successful whereas firing of preformed calcine charges yielded acceptable sinter products . Batch tests were made to study the effect of the following variables on the sinter quality : Size of green pellets in the charge , quantity and type of internal carbonaceous fuel used , depth of sinter bed , moisture content of the charge , flux additions , and binder additions . The batch and continuous sinter tests showed that minus 1 / 4 - inch pellets prepared from a mixture of the calcine , coke , dolomite , and water gave sinter cakes analyzing 57 to 61 percent iron and 0.05 to 0.02 percent sulfur .

Dec 1, 1963

By M. B. Cooke

In the course of investigation now in progress by the Bureau of Mines into the nature of " gum forming" constituents of gasoline , several gasolines and other petroleum products were heated in a small bomb , and pressures of considerable magnitude were developed . As the Bureau has received many inquiries for data showing the pressure that may be developed in a still when gasoline or other oil is subjected to elevated temperatures , it was thought advisable to record the pressures observed at various temperatures in the course of this work . data were merely a by- product of the main investigation . These Gasoline and similar products are very complex mixtures , and it is difficult to determine accurately the true vapor pressures , hence the vapor pressures of the oils used in these tests have not been studied in detail , but the data obtained may be taken as representative of the pressure- temperature relations of the various oils in commercial work.

Jun 1, 1922

By Oliver C. Ralston, Foster Fraas

The electrostatic separation of solids utilizes the forces exerted when electrically charged particles of the solids are present in an electric field . The charges may be acquired by various means (5) , and when the acquisition or loss of charge depends on the property of the particle , separation can be obtained between particles having different properties . A property commonly utilized in present - day separators in conductance . Charging also may be accomplished by bringing the particles into intimate contact with various surfaces . This is sometimes described as a " frictional electrical effect. The charge , or specifically the polarity of the charge , in this latter case evidently depends on the property known as the contact potential , as has been explained in the discussion of a paper (7) and in several other papers (10) . Separation by this method is accomplished in two steps - a charging step , in which the particles are brought into intimate contact with an electrification surface , and a separation step , in which the charged particles are separated in an intense electric field . Descriptions of such methods may be found in the literature (2) , (7) , ( 8) . Even as early as 1909 , Blake and Morscher (2) described the charging of particles by intimate contact followed by separation in an electric field . They also state that the polarity of the electrical charge acquired by the particles depends on their composition . O'Brien ( 8) presented several designs of apparatus . He obtained electrification by means of a wiping action , either on inclined plates or in rotating cups , in which a centrifugal force was imparted to the particles .

Nov 1, 1942

By James P. Bennett

In this Bureau of Mines study, portions of four acidproof bricks (two red shale and two fireclay) were exposed to 20 wt pct RCI at 900 C for periods of 30 days. Three different techniques were selected to deter-mine volume expansion of these materials after exposure. Linear expansions ranging from about 0.02 to 0.12 pct were noted from Ta pin and dilatometer measurements. The use of strain gages to measure expansions was not successful. The red shale and fireclay brick with the lowest apparent porosities had the lowest expansions. Expansion data obtained by direct measurement of samples exposed for 30-day periods or by dilatometric measurement of autoclaved samples ex-posed for 2 h were comparable. This suggests the use of an accelerated autoclave exposure procedure for determining volume expansion effects of ceramic materials in acid environments.

Jan 1, 1985

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006