Search Documents

By M. A. Mahtab

This report presents the geometric parameters (attitude, spacing, extent, and aperture) of fracture patterns in a selected portion (study area) of San Manuel copper mine, Arizona. The geometric parameters are quantified for input to structural analyses for studies of the influence of fractures on cavability of ores. Using an orientation analysis procedure developed earlier by the Bureau, three prominent and nearly orthogonal sets of fracture orientations were delineated in the study area. Sets 1 and 2 dip nearly vertically, and generally strike east-west and north-south, respectively, whereas set 3 is nearly horizontal. Both a horizontal rotation (of 14° to 26° for sets 1 and 2, respectively) and a tilt (of 20° for set 3) is shown to occur between the 1415 and 2015 levels of the mine. Gomparison of the three major rock types present in the study area (quartz monzonite, monzonite porphyry, and rhyolite) show that the rhyolite is characterized by short extent, small spacing, and tightness of fractures as well as the general absence of fracture set 3, which may account for its generally observed strong resistance to caving.

Jan 1, 1973

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By R. R. Sayers

"Health hazards in the mining industry may be attributed to (1) abnormal conditions of the air, (2) improper sewage disposal, (3) bad drinking water, (4) bad illumination, and (5) local mechanical irritation.Abnormal conditions of the air may be due either to physical or chemical changes. The physical changes are (1) abnormal temperature, (2) abnormal humidity, (3) air movement, and (4) presence of dusts. Dusts may be either poisonous, as salts of lead, arsenic, zinc, or mercury; or nonpoisonous, as dust from coal, silica or quartz, limestone, gypsum, or silicates. Chemical changes may be due to changes in the normal constituents, as lowered oxygen or increased carbon dioxide; or to the addition of abnormal constituents, as carbon monoxide (white damp), hydrogen sulphide (stink damp), sulphur dioxide, methane (marsh gas, fire damp), hydrogen, and nitrogen.Effects of High Temperatures and Humidities The effects of various temperatures and relative humidities have been studied in mines in many countries. Harrington and myself studied them in the metal mines of this country and, in a report written recently, they have been summarized as follows:A. Remaining at rest in saturated air at 91 1/2° F, for one hour, With no air movement caused -1. An increase in body temperature;2. A moderate increase in pulse rate;3. Profuse sweating;4. After effects of dizziness and weakness with air movement caused ¬1. Slight or no increase in body temperature"

Dec 1, 1924

By Lucien Eaton

The mining methods described in this paper are those used in a large mine producing hard specular ore on the Marquette Range in the Upper Peninsula of Michigan. Although the conditions of mining are unique in this district, they are similar to those in many other districts, and information in regard to the methods used and the results obtained should be of interest. The methods now used are an outgrowth of those of former years which have been adapted to conform with improvements in mechanical appliances, changes in the wage scale and labor supply, and the&apos; selling price of the product. The mine is situated&apos; at Ishpeming, in the Upper Peninsula of Michigan, 16 miles west of Marquette, its shipping port on Lake Superior.

Jan 1, 1929

By W. E. Wallace, V. Robinson, M. F. Keane, V. Vallyathan

"An in vitro study of the biologic responses of surface-modified and native silica and kaolin was made to provide comparative information on the supression of cytotoxicity by pulmonary surfactant. The release of alveolar macrophage cytoplasmic enzyme, lactate dehydrogenase (IDH), and lysosomal enzymes B-N-acetylglocosaminidase (B-NAG) and B-ghucuronidase (B-GLUC) and sheep blood-cell hemolysis were moni¬tored as indicators of cell membrane damage and cytutoxicity. Surface modification of silica and kaolin with dipalmitoyl lecithin (UPI) resulted in complete abrogation of cytotoxicity of both minerals. These findings indicate that surface modification of minerals with different adsorption properties by pulmonary surfactant generally lessens their prompt adverse effects.INTRODUCTIONAcute and chronic silicosis are well-characterized clinical and pathologic entities resulting from the inhalation of crystalline silica (Morgan and Seaton, 1984). Kaolin, a layered aluminosilicate clay frequently mined and used in manufacturing, contains tetrahedral silica alternately layered with alumina octahedra. Kaolin is relatively .inert biologically, and distinctly greater pulmonary burdens are seen in patients with kaolinosis than are seen in patients with silicosis. Crystalline siliea (quartz) induces a significantly greater degree of fibrosis in exposed animals in vivo than does kaolin (Hamilton and Hardy, 1974; Parkes, 1982; Hunter, 1976; Sheers, 1964; Warraki and t-lerant, 1963; Lynch and Mciver, 1954; Lapenas et al., 1984).This difference in pulmonary disease associated with the two types of dust is not reflected by in vitro cytotoxicity as Jetermined by pulmonary macrophage bioassays or erythrocyte hemolysis. Cytotoxicity studies using crystalline silica and kaolin of similar size fractions show comparable bioassay response on a mass basis. These cellular bioassays, therefore, do not correlate with the relative in vivo pathogenicity of silicates."

Jun 1, 1988

By Richard H. Singleton

Native asphalt was produced in 1980 by six companies in four States. Leading States were Texas and Utah. Output decreased 22% in 1980 to 1.25 million tons while value decreased 2% to $25.0 million. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert, Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. The product was used mainly in street and road repair. Gilsonite was produced by American Gilsonite Co. in Uinta County, Utah, and by Ziegler Chemical and Mineral Corp. in Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1981

By S. J. Pearce

"INTRODUCTION AND SUMMARYComplaints have been made regarding dust respirators that may be used in coal-mining operations. Some of these complaints may be due to improper use of the respirator, inadequate knowledge of its purpose and mode of functioning, poor choice, poor fitting, or inadequate maintenance. It is hoped that this circular will answer these complaints by discussing the various factors relating to the proper use of dust respirators in general and in coal mines in particular.It is pointed out that dust respirators are not to be used as a substitute for dust-control measures. The construction, functioning, choice, fitting, and maintenance of dust respirators are discussed.FIELD OF USEThe function of the dust respirator is to prevent the wearer from inhaling harmful quantities of dust by removing dust from the air he inhales.A dust respirator is not to be used as a permanent substitute for dust-control measures. It is to be used as a temporary substitute until dust-control measures can be instituted or as a protective means where dust-control measures are impracticable, as in applying rock dust in bituminous-coal mines.The following sections of the ""Federal Mine Safety Code for Bituminous-Coal and Lignite Mines in the United States"" 2/ emphasize the fact that every effort should be made to keep the amount of dust in the air of the working places as small as possible:"

Mar 1, 1950

By D. S. Kingery

Recent Federal coal-mine inspections have revealed some good and some definitely hazardous practices and systems for transporting; handling, and storing lubricants in and about coal mines. Improper storage or handling of. lubricants in coal mines has caused disastrous mine fires or, by supporting combustion, has made fires from other sources more difficult to fight. Careless handling of grease and oil around electrical equipment wastes much oil and permits entrance of grit and foreign substances into the working parts, which causes excessive wear and increases the possibility, of electrical ignition.

Jan 1, 1943

By Charles B. Kenahan

Vanadium is subject to only light corrosion in phosphoric acid at temperatures up to 60° C. and has a moderate corrosion rate in this acid at 100° C. It is relatively corrosion resistant in sulfuric and hydrochloric acids up to 60° C, but corrodes rapidly at 100° C. It corrodes rapidly in dilute nitric acid at 35° C. Vanadium is almost inert in 10-percent solutions of formic, acetic, lactic, tartaric, and citric acids; in 9-percent oxalic acid it corrodes slowly up to 60° C. and rapidly at 100° C. Vanadium is resistant to corrosion in substitute ocean water, tapwater, and in 3-percent sodium chloride and 10-percent sodium hydroxide solutions. It is readily attacked, however, by 20-percent ferric chloride, 20-percent cupric chloride and 5-percent mercuric chloride solutions. Vanadium is protected by contact with magnesium, aluminum, and steel SAE 4130 in substitute ocean water, by magnesium and aluminum in 3-percent sodium chloride solution, and by magnesium in tapwater. Vanadium protects copper in substitute ocean water. When vanadium and stainless steel are coupled in sulfuric acid solutions, both metals are usually unaffected by contact, whereas the corrosion rate of titanium in sulfuric acid is greatly reduced by contact with vanadium.

Jan 1, 1962

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By George L. Gates

This report presents is an evaluation by the Federal Bureau of Mines of the effect of clay-water, brine, and oil-base drilling fluids on the productivity of test wells drilled on the Umiat anticline in U.S. Naval Petroleum Reserve No. 4 in northern Alaska. Eleven, wells were drilled on the Umiat structure as part of the U.S. Navy&apos;s extensive exploration of the Reserve during 1944-53 to determine the possibilities for oil production. The Federal Geological Survey cooperated in the exploration program and has published a comprehensive report3/ on the geology of the area and case histories of the wells. The re¬port also includes the results of special studies by the Bureau in connection with the drilling and coring of well 9 with oil-base mud in hole and was the source of much of the information used in preparing this publication. Of the eleven wells, four were drilled with rotary tools and water-base mud (one of the water-base muds was an oil-in-water emulsion mud), five were drilled with cable tools with brine in the hole, one was drilled with cable tools with brine in the hole and later reamed with rotary tools and crude oil, and one was drilled with rotary tools and oil-base mud. Although all of the wells penetrated sandstones that contained oil and gas, some were productive and others were not. The latter two wells, one completed with crude oil in the hole (with some added brine) and the other with oil-base mud, had the greatest productive capacities. The wells drilled with cable tools and brine in the hole had lower productive capacities. In contrast, two of three wells completed with rotary methods and fresh-water drilling mud and the well com¬pleted with rotary and emulsion mud were unproductive.

Jan 1, 1960

By D. C. Fleck

This report describes a method of using sodium for reducing titanium tetrachloride, developed at Boulder City, Nev., as part of the Federal Bureau of Mines effort to improve the extractive metallurgy of titanium. Finely divided titanium metal, titanium lower chlorides, or a mixture thereof was produced in a continuous operation at temperatures between 105° and 205° C. by the reaction of molten sodium and vaporized titanium tetra-chloride in an agitated bed of finely divided inert solids (powdered sodium chloride or the reaction products). Composition of the product was controlled by varying the relative quantities of sodium and titanium tetrachloride used. A description of the operations and analytical data of the reaction products are given.

Jan 1, 1960

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By H. B. Brunot

A complete list of permissible mine equipment , tested and approved by the Bureau of Mines previous to January 1 , 1947 , was published as Information Circular 7432.27 A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 was published as Information Circular 7465.3/ The present list supplements Information Circular 7432 and includes all of the equipment approved during the calendar years 1947 , 1948 , and 1949. It therefore supersedes Information Circular 7465. The list also includes an appendix ( No. 2 ) giving the symbol that must be used by every cable manufacturer in marking trailing cables that have passed the test for flame resistance as stated in the amendment of October 21 , 1947 , to Schedule 2E . The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification . Thus , Information Circular 7432 showed six air compressors on the active list ; five additional compressors , Nos . 7 to 11 , inclusive , in this category were approved during 1947 , 1948 , and 1949 . Several items that were listed in Information Circular 7432 have been repeated in this circular where it was necessary to show that approvals of such equipment were extended to cover an additional voltage rating or other changes . Equipment listed in these circulars is approved by the Bureau of Mines only when found , upon inspection and test , to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal -mining industry . The use of such equipment in mines known to be gassy , as well as in those that may become so , is earnestly recommended in the interest of safety . This circular is published so that the industry may be kept informed as to the many types of machines , devices , and lamps that are available for reducing explosion and other hazards incident to coal mining . This circular and Information Circular 7432 give the complete list of permissible mine equipment that is available under the various classifications .

May 1, 1950

By R. E. Tremoureux

This paper describing the methods and costs of quarrying limestone at Sloan, Nev., is one of a series of similar papers being prepared for and published by the Bureau of Mines on this industry in the United States. These papers are designed to disseminate information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods Employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The quarrying operations at Sloan are interesting not only from a technical viewpoint and because of the magnitude of the deposit, but also because the quarry is located in a desert region far removed from the centers of population where lime is used. The quarry and plant are in Clark County, Nev., 20 miles west of Las Vegas, which is the nearest town to the site of the Boulder Canyon Dam. Sloan is on the main line of the Union Pacific Railroad connecting Salt Lke City and Los Angeles. The latter city is 280 miles from Sloan and it is the shipping, point for all supplies.

Jan 1, 1932

By C. J. Wilhelm, John M. Devine

"Hydrogen aulphide associated with natural as was noted as early as at Point Albino, Canada. 4 The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence ma by no means common. However, in recent years, with the development of the producing zones of west Texas and the Texas Panhandle the production of ""sour"" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor-frequently a major problem—in the drilling and operation of any wells in those areas.The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen sulphide. From the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. 5 Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.6"

Sep 1, 1931

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956