Search Documents

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By H. E. Heide

The serious shortage of domestically produced asbestos during the war prompted the Bureau of Mines to investigate reported asbestos deposits in Alaska. The most promising' appeared to be these in the Cosmos Hills and Jade Hills areas along the Kobuk River in northwestern Alaska. The deposits along the west side of Shungnak River, a tributary of the Kobuk River, were the first to be investigated by the Bureau, in the summer of 1944. Four bulldozer trenches were excavated, from Which a 2-ton sample was taken. This sample was shipped to Rolla, Mo., for testing in the Bureau of Mines laboratory. In the summer of 1945 an investigation of asbestos deposits on Cosmos Creek, also a tributary of the Kobuk River, was begun; the work was completed during the field season of 1946.

Jan 1, 1949

By R. L. Hopkins, H. T. Rall

A continuous method has been developed for preparing thiolacetic acid . Acetic anhydride and hydrogen sulfide are passed concurrently over an amine ion- exchange resin , under 20 - psi pressure . The thiolacetic acid , a product of the reaction , is flashed continuously from the crude reaction mixture and is purified by fractional distillation . The yield of thiolacetic acid is in excess of 80 percent based on the acetic anhydride charged . INTRODUCTION In the synthesis of reference compounds needed in the identification of sulfur compounds in petroleum , thiolacetic acid has become an important reagent because of its use in the synthesis of thiols by addition to appropriate olefins : R - CH = CH₂ + CH3 - COSH R- CH2 - CH2 - S - COCH R - CH2 - CH₂ - SH + CH3COONa NaOH (1 ) The commonly used procedures for its preparation , as described by Clark and Hartman (1 )4 and by Ellingboe (2 ) , are based on the batchwise reaction of acetic anhydride with hydrogen sulfide :

Jan 1, 1964

By J. A. Herdlick

Under authority of the Strategic Materials Act of June 1939, the Federal Bureau of Mines, in cooperation with the Geological Survey, began a broad program of investigation of the strategically important chromite deposits in Sweetgrass, Stillwater, and Carbon Counties, Mont. Extensive occurrences of chromite along the Stillwater Complex in Stillwater County were investigated. The two principal deposits, The Mouat-Sampson and Benbow mines, ultimately were developed and placed in production by the Federal Government. As a part of this general development program, the Carbon County chromite deposits near Red Lodge were examined by Bureau of Mines engineers in 1940, and by the Geological Survey .1-1 1942. The district was examined earlier by Schafer, and the Four Chromes area is mentioned briefly by Westgate. Although the Red Ledge deposits were considered to be of minor importance as compared to those of the Stillwater Complex, several of the ore bodies were adaptable to open-pit mining' methods, and one large deposit on Line Creek Plateau was readily accessible to the Red Lodge-Cooke highway. In 1941, the U. 3. Vanadium Corp. began mining crude lump-chrome ore from the deposit on Line Creek Plateau to supplement national stockpiles, which were being depleted by the rearmament program and the disruption of chrome-ore imports by the European war. Access roads gore constricted to Hellroaring Plateau, and the mining operations were extended to that area. A gravity concentrator with a capacity of 200 tons per day was built and operated at Red Lodge to beneficiate lower-grade ore from the district.

Jan 1, 1948

By D. A. Reynolds, R. G. Travis, James J. Dowd, R. F. Abernethy

"1. Reserve estimates have been made for eight coal beds in Monongalia County, W.Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil¬lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Monongalia County, as determined by this investigation, is 47.9 percent. This percentage is based on the total thickness of coal (less partings three-eighths inch thick or more) in the bed rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Monongalia County, the recoverable reserves are estimated at 1,577 million tons as of January 1, 1954.4. Monongalia County coals of the major producing beds are of high-volatile a bituminous rank.5. The Pittsburgh and Lower Freeport beds in this county yield coal that can be used as metallurgical coal, especially when blended with low-volatile coals. The Lower Freeport coal is coked singly and in beehive ovens, and makes good metallurgical coke.INTRODUCTIONThe investigation to evaluate the reserves of coking coal was planned to cover three phases: (1) Estimation of known measured and indicated recoverable reserves of all coking coal; (2) study of methods of upgrading marginal coals through effective preparation; and (3) study of carbonizing properties of coals and coal blends not now widely used for metallurgical coke making."

Jun 1, 1956

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By L. C. Brichta

During a study of the Badger-Peacock area from October 1950 to June 1953, the Federal Geological Survey and the Federal Bureau of Mines completed nearly 98 miles of resistivity profiling and drilled 96 test holes aggregating 17,628 feet of bore, In addition, seismic profile measurements were made along 8 traverse lines for an aggregate length of about 16,600 feet. The geophysical surveys were conducted by the Geophysics Branch of the Geological Survey; the drilling was done by the Bureau of Mines. Electrical-resistivity measurements disclosed 21 low-resistivity anomalies and 1 high-resistivity anomaly. Correlation of the resistivity data with the geological information revealed by the drilling disclosed that the low-resistivity anomalies indicated either slumped shale deposits in limestone sinks or undisturbed deposits of shale lying in erosional depressions in the limestone. The high-resistivity anomaly indicated hard, undisturbed limestone at or near the surface.

Jan 1, 1958

By Paul T. Allsman

This paper gives the cost and describes the mining of 55 tons of nickel-bearing rock by hand methods from a prospect in southern Nevada, June 15, 1937, by the Mining Division of the Bureau of Mines. The geology, mineralogy, and problems related to future development also are discussed briefly. The main object was to obtain a 55-ton sample within the limited period during which funds were available; little time was available to make a first-hand detailed study of the possibility of commercial ore deposits being found. The sample was desired by the Metallurgical Division of the Bureau for experimental purposes at the Electro-Metallurgical Station at Boulder City, Nev. The term "ore" is used loosely in the following discussion to designate dike material containing nickel and copper, without consideration of its commercial value. ACKNOLEDGMENTS Material concerning the geology and mineralogy of the prospect and district as obtained from Geological Survey publications by Bancroft3/and Longwell4/.

Jan 1, 1938

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By Fred N. Kissell, Jerry C. J. Tien, Edward D. Thimons

At coal mine working faces, simultaneous application of three basic elements reduces the methane explosion hazard: (1) adequate ventilation, (2) regular monitoring of gas concentrations, and (3) the elimination of ignition sources. This paper reviews the application of these elements in a manner relevant to Chinese coal mines. Adequate ventilation is provided by using the mine entries to convey air for the long distances between the mine portal and the working sections (main ventilation systems) and then using line brattice or ventilation duct (face ventilation systems) to convey air the last hundred meters to the working face where coal is broken and removed. The air quantity provided is enough to safely dilute methane and the air velocity is enough to prevent layering. Gas concentrations are regularly monitored in accordance with regulations using knowledge of the circumstances under which the highest concentrations are likely to be found. Ignition sources are eliminated by ensuring that electrical equipment does not ignite methane, that sparking from cutter picks is minimized, and that smoking by workers is strictly forbidden. Risk-reduction studies using fault-tree analysis have shown that large reductions in explosion risk only result from multiple preventive actions. For example, a ventilation upgrade or a methane monitor upgrade by itself offers risk reductions under 50 pct. A risk reduction of 90 pct. or more would typically require much more. Other studies have shown that the everyday vigilance of those working underground is as important as engineering design.

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall As used in the mills to replace losses from evaporation, seepage, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation- Which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects.

Jan 1, 1932

Reduce dust exposure of longwall shearer operators by keeping them upwind of the primary cutting drum. Approach Use a different coal cutting sequence by cutting from headgate-to-tailgate, making the cleanup pass from tail-gate-to-headgate. How It Works The cutting action of the shearer drum is usually the primary source of respirable dust at longwall shearer faces. Dust exposure of the shearer operator is deter-mined by his position relative to the lead drum, which is normally in the raised position taking a full sump. On long-wall faces where the cut pass is taken from tail-to-head, against the primary airflow, the shearer operators must remain at their controls, on the return-air-side of the primary dust source, to maintain proper control. A simple method to lower shearer operators' dust exposures is to extract the primary coal from head-to-tail, thus positioning the operators up-wind of the lead cutting drum. The bottom coal is then cut, and the floor cleaned by the trailing drum during the tail-to-head cleanup pass. This sequence places the primary dust source, the cutting action of the shearer drums, on the return-air side of both shearer operators, except when cutting out at the longwall headgate.

Jan 1, 1984

By Joseph H. White

In its investigations looking to the improvement of health condi- tions and the increase of efficiency in the mining industry, the Bureau of Mines, in cooperation with the Bureau of Public Health, is studying sanitary conditions in and about mines with the intent of pointing out how those conditions that are a menace to the health of the miner may be most efficiently removed or remedied. An out- line of sanitary betterment work at mining villages in the Birming- ham district of Alabama has already been published by the bureau," and in this bulletin are presented suggestions on the planning of mining towns and the construction of miners' houses. The bulletin does not pretend to be a treatise on the so-called "housing problem," and mentions sociologic issues only incidentally. It is assumed that the influence of proper shelter on health is understood and that not a lack of appreciation so much as a lack of knowledge of the best remedies is responsible for many of the undesirable conditions that exist at mining towns. The purpose of this bulletin is to supply facts on the building of well-lighted, well- ventilated, warm, attractive, and economical houses for miners, these houses being assumed to be units of an industrial village or town the building and management of which are under the control of a corporation, so that special conditions hold which do not apply to houses built and owned by individual miners. From this it is not to be inferred that the company-controlled town is the best system or the only one in vogue. The discussion of this side of the subject in all its phases is too involved to be included in this paper. One element in favor of the company-controlled town is its possible immediate responsiveness. Hence this assumption. Also the assumption is made that a-new isolated town is being built, and hence the selection of the site, the arrangement of the streets, and the situation of the houses are discussed before the house itself is treated, for one of the most important factors in obtaining an economical sanitary house is a well-selected town site. Many of the suggestions, however, may be applied in improving conditions in existing towns, in building new houses in old towns, or in repairing old houses. Emphasis must be laid on the fact that as a rule a mining village has a shorter life than a manufacturing town. Economy is emphasized frequently because the discussion is predi- cated upon the assumption that the miner himself is to pay for all that he gets. House rent will doubtless be expected to bring in a reasonable return on all money invested in streets, sidewalks, water supply, sewer system, and houses; in other words, the town is to be run on a business and not on a paternal or charitable basis. "Fair and reasonable" precludes, of course, the idea of excessive returns. Some companies do not consider it good policy to realize as high a rate of interest as an independent realty company would be war- ranted in realizing. Under some circumstances part of the town improvements might be charged as "expense of the industry," that is, to the consumer. The isolation of a mining town introduces a unique responsibility. As the miners are practically obliged to rent the company houses, the officials of the company ought to scrutinize all expenditures in- volved so that house rent may be reduced to a minimum. In a way the town builders are placed in the position of trustees. They deter- mine, within certain limits, what proportion of a man's wages shall be spent on house rent. This consideration should restrain fanciful and unnecessarily expensive building; the other extreme should like- wise be avoided. True economy should be distinguished from cheap- ness. Ugly, insanitary, uncomfortable shacks should not be built even if, because of their cheapness, there is a demand for them from tenants. The obligation of the industry to society as a whole as well us to the tenant ought to forbid this. A cheerful, strong, healthy, virile race will not rise out of the filth and squalor of cheap hovels. An insanitary environment often does its damage slowly and silently; vitiated air does not, like mine gas, announce its deadly work by an explosion. As Talbot⚫ says: Health depends in part on freedom from infection. The probability of obtain- ing that freedom will be greatly increased by maintaining the body at a high state of vigor, or "vitality," as it is popularly called. This implies the promo- tion of all agencies which have to do with the physical well-being as well as with the control of sources of infection. Many men realize that in building houses for their workmen they are invested with a peculiar responsibility that must be wielded wisely, and in large developments they call into consultation the land- scape architect, the sanitary engineer, and the building architect, as well as the mining engineer.

Jan 1, 1914

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By L. C. IlsLey

"According to accident statistics, issued from time to time by the Department of the Interior, Bureau of Mines covering fatalities in coal mines, between the years 1870 and 1921 there were 4,897 deaths caused by explosives. The legislatures and safety commissions of the various mining States have Elected and formulated many excellent regulations in regard to the handling and use of explosives in an endeavor to keep this class of accidents as low as possible. An analysis or comparison of the explosive, regulations issued by over thirty States would make a very long paper, however, by subdividing according to phases and issuing several papers it is believed that the material will be more readily available. The first phase was treated in Serial No. 2405 of the Bureau of Mines (""State and Federal Electrical Shot-Firing Regulations,"" issued in October 1922) which gave a compilation of such regulations as apply strictly to electric shot-firing. The second phase under consideration is ""Who may set off blasts in coal mines.""In some States, the person who does the firing must be an ""authorized shotfirer,"" while in other States he must have proved his ability to do this work, and again in other States he is ""any person."" The present paper covers rules and regulations relating to this phase of shotfiring, and those States having similar regulations have been grouped as follows."

Jun 1, 1923

By A. D. Garman

This paper presents one of a series of digests of foreign mining legisla- tion and court, decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Latin America has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it is being referred through the courtesy of the Department of State. Individual abstracts of the laws of each of the countries herein discussed have been prepared and published separately. This general summary is presented for the use of mining engineers and investors whose interests extend over the borders of a single country. It is also designed to bring out certain general principles of mining law and, so far as feasible, to indicate the trend of mining legislation in South and Central America. In order to gain perspective, the details of legislation are not com- pletely covered in this paper, but an effort has been made to bring out essential differences as well as points of similarity in the laws of the various countries. The course of legislation is first traced chronologically and the points discussed are then arranged in tables in somerhat greater detail. .Si. With a very few exceptions the existing mining legislation of Spanish America is a development, of the Spanish "Law Decree of Bases" (more briefly referr- ed to as the "Decree-Bases") of 1868. This in turn was influenced, particularly in its classification of minerals, by the French law of April 21, 1810.

Jul 1, 1930

By A. L. Engel

Included in the program of the Rare and Precious Metals Station, Metallurgical Division, Bureau of Mines at Reno, Nev., are investigations of treatment methods for ores representative of various mining districts throughout the country. The samples received for this work may come from areas only recently explored or from newly discovered ore deposits in older mining districts. The present investigation deals with a case of the latter type, the. ample having come from a section that has a past record of considerable precious. metals production. The application of current treatment methods to this type of ore seems to offer excellent possibilities of satisfactory economic results. Definite identification of the silver mineral in this ore asthe chloride cerargyrite, AgCl, adds considerable interest to, the investigation, as in many cases where silver occurs in comparatively small amounts in an ore it is not possible to identify the particular mineral carrying the silver or else it is contained in or combined with other more common minerals. Cerargyrite is the "horn silver" of the bananza period and is mentioned in many accounts of pioneer mining of high-grade ores The occurrence of this mineral in finely disseminated form it a low-grade ore is believed to be unusual. The sample investigated was obtained from the' Bullfrog District neat Beatty, southwest Nye County, Nevada. The ore contained 16.7 ounces of silver per ton of ore, 0.007 ounce gold, and 0.32 percent copper in a silicious gangue, with accessory minerals, including iron oxides and scorodite; the hydrous iron arsenate.

Jan 1, 1949

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900's, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956