Search Documents

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By H. A. Watson

Fluorine-containing polymers are comparatively new materials that exhibit very desirable characteristics not usually found in non-fluorine containing polymers. Among these characteristics are heat and flame resistance, desirable electrical properties, and chemical inertness. Polytetrafluoroethylene and polymonochlorotrifluoroethylene are examples of such polymers commercially available. In practical applications it is reasonable to expect thermal position of these materials if they are subject to high enough temperatures. The temperatures at which thermal decomposition takes place and the nature of the gaseous products of decomposition are considered pertinent data in intelligent use of these materials. The purpose of the tests discussed herein was to determine: (1) The temperatures at which gases were produced when small specimens of the two polymers were located and (2) determine the identity of the major constituents of gaseous products.

Jan 1, 1950

Develop a method for mapping planar geologic features in deep underground mines where the presence of metal interferes with compass readings. Background A fundamental problem of mapping planar geologic features in deep underground mines is the presence of metal (water and air pipes, track, equipment, etc.), which affects the accuracy and consistency of compasses. Present geologic mapping methods include use of transits or theodolites, both of which are cumbersome and time consuming to use. To complicate the mapping, process each planar feature must be surveyed, and if that feature is not apparent on the opposite wall, it cannot be mapped. Another method of mapping is to stretch a tape measure between two survey spads and place a string along a planar feature on one wall and out into the opening until it intersects the tape measure. This method, in addition to being time consuming, is also inaccurate. Because detailed mapping of planar geologic features deep underground involves many repetitive measurements, a quick, accurate, and reliable method for making such measurements was necessary. The geolaser was developed to make such measurements in deep underground mines where metal interferes with conventionally used compasses.

Jan 1, 1990

Studies on coal mine drainage sludge densification have led to the following conclusions: 1. Coal mine waters containing iron principally in the ferrous (Fea+) state can be treated by a modification of the commonly practiced lime neutralization process to yield a ferromagnetic sludge. The sludge, presumably composed in large part of a hydrated ferrosoferric oxide (Fe304.xH20), is much denser and faster settling than the ordinary "yellowboy" sludge obtained by lime neutralization and aeration at ambient temperatures. 2. The magnetic sludge preparation technique involves (quantitative) precipitation of iron (largely as Fe(OH)2) by the addition of hydrated lime to a pH of 8.5, separation of the resulting sludge from the aqueous phase, and heating of the sludge concentrate to at least 80 C (176 F), preferably higher, followed by mild aeration. 3. Magnesium, present as Mg2 in most coal mine drainage waters, inhibits the formation of the magnetic sludge. This inhibition can be adequately minimized by keeping the pH below 9.6 during lime addition (thus avoiding the coprecipitation of Mg(OH)2) and by separating the sludge from the bulk of the aqueous phase before the heating step, as indicated in (2) above. 4. Aluminum, commonly present in coal mine drainage waters, also inhibits the formation of the magnetic sludge. This inhibition is of practical significance when the molar ratio of aluminum/total iron is greater than 0.18. Below this value, sludges are still appreciably magnetic, but are bulkier and slower settling than those obtained when aluminum is absent. Unlike magnesium inhibition, aluminum inhibition cannot be minimized by the scheme indicated above, since aluminum precipitates as Al(OH)3 near pH 4 and remains dispersed within the sludge. 5. The limitation on aluminum content is probably the most serious restriction affecting the feasibility of the magnetic sludge process as presently conceived. Nevertheless, a limited review of available water quality data has indicated that, in terms of relative acid and iron loadings, a significant number of major coal mine discharges in the eastern Ohio River basin may be amenable to treatment by a magnetic sludge process. 6. Data from tests on the use of magnetic seeding materials indicate that seeding did not enhance the formation of a magnetic sludge under the experimental conditions employed.

Jan 1, 1971

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

By Steven J. Page, John A. Organiscak

The amount of airborne respirable dust generated from break- age of different coals varies widely. This research was conducted to identify the facets of airborne respirable dust liberation from the coal product. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals to investigate the various factors influencing airborne respirable dust generation. Bituminous coal samples from 8 mines (5 U.S. and 3 Polish) were uniformly prepared and processed through a double roll crusher located in a low air velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific quantity of airborne respirable dust generated. The results of this investigation build upon previously published results, which indicated that a combination of several factors are associated with the generation of airborne respirable dust. One factor involved is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. However, since coals of high moist fuel ratio (high rank) are generally more extensively cleated, it is suggested in the present work that the degree of cleating is directly responsible for the quantity of respirable-sized particles produced in the crushed product material for eastern U.S. coals. This is implied by the relationship of ash content and at least one mineral constituent (pyrite, determined from pyritic sulfur analysis) to the percentage of airborne respirable dust. To validate this hypothesis, a description is offered that is based on known coal petrography. Another key factor is the effect of air dry loss moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The air dry loss moisture factor appears to control the amount of airborne respirable dust that is liberated from the product. The resultant effect of these factors is that different percentages of coal particles smaller than 10 µm are dispersed as airborne respirable dust with a well-defined peak in the normalized airborne respirable dust for a narrow range of air dry loss moisture - ash ratios. A clear delineation of coals, based on well-known proximate analysis characteristics, that generate the most respirable dust appears to be possible. It was also shown that the dust-generating characteristics of coals could be reasonably described by both the moist fuel ratio

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

By Valois R. Shea-Albin

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq's equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 2010

By J. M. Stuve

A novel calorimetric solution technique, recently developed at the Bureau of Mines, was tested using synthetic samples of chalcocite (CU2S) and covellite (CuS). The solution of these refractory sulfides was accomplished by oxidation with bromine in a moderately acidic, aqueous solution. The resulting values for the standard enthalpies of formation (?Hf°, 298.15) for CU2S(c) and CuS(c) were -18.1 ±1.1 kcal/mol and -13.3 ±1.1 kcal/mol, respectively. These values are in good agreement with published formation values derived from other methods of physicochemical measurement.

Jan 1, 1982

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By James W. Myers

The Bureau of Mines studied factors affecting ignition of coal mine refuse and on methods for control of burning. Laboratory experiments showed that air permeates more readily through segregated than through nonsegregated refuse and that air permeability is greater through coarse than through fine particle refuse. Minus 3-1/4-inch refuse ignites spontaneously more readily than minus 1/4-inch refuse. The burning of a 1,000-pound conical coal pile was con-trolled by capping with an 18-inch-thick layer of minus 1/4-inch refuse containing 37 percent combustible. In field trials, the burning of refuse at operating mines was controlled by capping with a layer of fine refuse. Water, applied as a spray or by injection, quenched surface flames and cooled the burning waste. Inspection of refuse piles at operating mines showed that the spontaneous ignition tendency is affected by the exposed surface relative to the total volume and the segregation of particles during dumping.

Jan 1, 1966

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By R. G. Knickerbocker, David Schlain, F. K. Shelton, J. H. Jacobs

"Many manganese ores contain from 0.1 to several percent cobalt. If such ores arc used for the production of ferromanganese, the cobalt is lost; on the other hand, if they are used for the production of electrolytic manganese, the cobalt can be recovered during the purification of the electrolyte.The production of cobalt in the United States is insignificant compared to the amount consumed, most of which is imported from the Belgian Congo. Cobalt-bearing manganese ores may therefore constitute an important reserve of cobalt in times of emergency. Moreover, the combined value of manganese and cobalt in some ores may be sufficient to warrant the recovery of both metals by the electrolytic manganese process, whereas the recovery of either manganese or cobalt alone might not be economically feasible.In view of the potential importance of manganese ores as a source of cobalt, a survey has boon made of the cobalt content of manganese ores. Most of the data have been obtained from analyses made in the Bureau of Mines, but valuable data have also been obtained from publications of the Geological Survey, various State publications, and other sources. Unfortunately, most published analyses of manganese ores do not include cobalt determinations; when such analyses were fairly detailed, but did not include cobalt, it was presumed that cobalt was not present in significant quantity.Information on the cobalt content of domestic manganese ores is given in table 1. Ores containing 0.1 percent or more cobalt are listed in table 2, and the districts in which such ores occur are shown in figure 1. Most of the known cobalt-bearing manganese ores occur in the southeastern part of the United States. A group of deposits in central Arizona and a few scattered deposits in other States also' contain cobalt."

Apr 1, 1946

By Walter R. Storms

"The New Mexico potash exploration described herein was begun in February- 1944 by the Federal Bureau of Mines with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County, N. Mex., by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the reserve and in the immediate vicinity.The Potash Reserve is located in secs. 26, 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of the city of Carlsbad. Drilling was done in secs. 26 and 35 of the reserve, in sec. 14 to the north, and secs. 25 and 36 to the east. All work was done on Government-owned, unleased land.The reserve may be reached from Carlsbad by traveling northeast by automobile for about 14 miles on paved U. S. Highway 62. This highway passes through the southern part of the reserve. Other parts may be reached by a State highway which passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Atchison, Topeka and Santa Fe Railroad also passes across the southern part of the reserve en route from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the Project and 22 miles from Carlsbad.Work on the project was greatly facilitated by the help of Ralph H. King, associate geologist, R. K. Bailey, geochemist, H. C. Spicer, geophysicist, Hope Bunker, junior geologist, and R. H Allport, district mining supervisor, all of the Federal Geological Survey; and Charles H. Johnson, who at that time was district engineer for New Mexico for the Mining Branch of the Bureau of Mines."

Apr 1, 1946

By J. E. Geier

This Bureau of Mines report reviews hypotheses for the mechanism by which water jets reduce the specific energy of cutting for drag bits. Several of these hypotheses are shown to be inconsistent with published evidence and new observations. The notion of a limiting cutting speed, above which water jets would be incapable of rendering assistance, is shown to be improbable. The hypothesis that seems most plausible is that specific energy reductions are mainly due to the erosion of crushed materials from in front of the bit. This hypothesis leads to a prediction that, for a given rock type and jet-bit configuration at a constant depth of cut, the reduction in bit forces should be a function of dM/dx, the jet energy spent per unit length of cut. This dependence upon dW/dx is shown to be consistent with other workers? results.

Jan 1, 1987

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

By Robert E. Barieau

This report describes a method for treating pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. The method makes use of a general nonlinear least-squares technique developed at the Bureau of Mines Helium Research Center. It is assumed that an adequate functional form is available for the expression of the compressibility factor as a function of either the molal density or the pressure. The functional form of the compressibility factor can be either linear or nonlinear in the parameters to be evaluated. Formulas are given for calculating variances and covariances of all parameters evaluated and for calculating the variance of calculated quantities of interest.

Jan 1, 1967