Search Documents

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By W. A. McKinney

The segregation process consists of heating crushed oxidized or mixed oxide-sulfide copper are with a copper-volatilizing salt and carbonaceous material at about 750° C. to produce metallic copper which is recovered from the furnace calcines by conventional sulfide flotation. The Bureau of Mines made a number of bench-scale laboratory tests on two copper ores to determine the relative merits of using halogen salts, potassium chlorate, or various salt mixtures as volatilizing agents in segregation of the copper. Laboratory investigation of typical siliceous and calcareous oxidized ores revealed that sodium chloride was a better segregating agent than the other salts. Calcium chloride, magnesium chloride, sodium fluoride, or potassium chlorate gave nearly as good segregation as the sodium chloride on the siliceous ore. Segregation of the calcareous ore with calcium chloride was nearly as good as that obtained with sodium chloride, but inferior segregation resulted when magnesium chloride, sodium bromide, or potassium chlorate was employed. The use of sodium bromide or sodium iodide on the siliceous ore, and of sodium fluoride or sodium iodide on the calcareous are, gave appreciably poorer segregation than sodium chloride or the other salts. Other tests of the ores, using mixtures of sodium chloride and the other halogen salts or potassium chlorate, gave segregation approaching that obtained with sodium chloride.

Jan 1, 1962

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By A. R. T. Denues

Liquid oxygen explosives are ordinarily made from a carbonaceous absorbent and from liquid oxygen of high purity. These explosives have a limited but definite field of usefulness; their properties have been described in the literature, which includes several publications of the Bureau of Mines, the most recent dealing with fire-retardant treatments.3/ It seems generally conceded that the outstanding hazards in the use of these explosives are their high inflammability and their relative sensitivity to mechanical action. Each of these topics has been studied, and some interesting practical results have been obtained. Treatments have been described[7] that render liquid-oxygen explosives prepared from granular carbonaceous absorbents practically immune to the action of igniting agents representing or exceeding practical hazards in violence.

Jan 1, 1941

By C. I. Pierce

Knowledge of the water content of oil-bearing formations is important in petroleum-reservoir evaluation work. Electric logging provides a means for making reliable estimates of water content if resistivity-saturation relationships representative of the formations are available. Relationships can be determined in the laboratory by a number of methods. This report describes and presents results of a laboratory investigation conducted at the Bureau of Mines Appalachian Experiment Station, Morgantown, W. Va. (1) to evaluate an evaporation method of attaining water saturations in sandstone samples when determining resistivity-saturation relationships and (2) to compare saturation exponents derived from data obtained, using different methods of achieving water saturations. A series of tests was conducted to determine the effect of evaporation on salinity distribution within the core specimen. Results of these tests show that a zone of high salinity was set up at the surface of a sample during evaporation and that long periods were required for the sample to reach resistance equilibrium after evaporation had ceased. Equilibrium time ranged from several minutes to several days, depending on the sample size and the technique used. The high-salinity zone was removed from the sample by using auxiliary porous material in capillary contact with the sample surface during evaporation. Salinity determinations and resistance measurements indicate that, at saturations greater than the minimum interstitial values, the mechanism of flow during evaporation was one of moisture migration mainly as a liquid from the interior of the test specimens to their exterior surfaces. The concentration of the contained brine remained essentially unchanged, except for a narrow zone near the evaporating surfaces.

Jan 1, 1958

By A. R. T. Denues

[Liquid oxygen explosives are ordinarily made from a carbonaceous absorbent and from liquid oxygen of high purity. These explosives have a limited but definite field of usefulness; their properties have been described in the literature, which includes several publications of the Bureau of Mines, the most recent dealing with fire-retardant treatments.3/ It seems generally conceded that the outstanding hazards in the use of these explosives are their high inflammability and their relative sensitivity to mechanical action. Each of these topics has been studied, and some interesting practical results have been obtained. Treatments have been described that render liquid-oxygen explosives prepared from granular carbonaceous absorbents practically immune to the action of igniting agents representing or exceeding practical hazards in violence.]

Jan 1, 1941

By R. L. Crosby

The effect of indium on the solid solubility of calcium and of silicon in magnesium was studied using metallographic, X-ray diffraction, and electrical resistivity techniques. The addition of 2 weight-percent or more of indium reduced the solid solubility of calcium in magnesium by forming a compound containing indium and calcium. Indium additions have no perceptible effect on the solid solubility of silicon in magnesium.

Jan 1, 1963

By Ott F. Heizer

This paper describing the mining practices at the mines of Massachusetts, Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in tie various mining districts of the United States. The author acknowledges the assistance of William C. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in the preparation of this paper.

Jan 1, 1930

By L. R. Burdick

Sulfur compounds have long been recognized as damaging pollutants of the air. A number of investigations have been made to determine the amount of such compounds existing in the air of various cities; moreover, some study has been given to the conditions affecting the concentrations. This paper summarizes published investigation and includes a bibliography on the subject. The methods of obtaining data have differed to the type of sampling, analysis procedure, hour of sampling, number of locations, and number of determinations made. Sampling methods include both the continuous type, covering a day or a number of days, and what can considered the ?snap? type, covering very short periods. Continuous sampling has, given data representing the average concentration at the location chosen but no information regarding variations from hour to hour, are none that might be said to represent the average for a city. The snap-sampling method, while not giving a true average for any one location or area, has in some instances made available date regarding variations of concentration during different hours of the day and at various locations or zones within the area chosen. Although the sulfur compounds in the air nay include sulfur dioxide, sulfur trioxide, hydrogen sulfide, and organic compounds of sulfur, most investigators report on the basis of sulfur dioxide. This gas unites with moisture to form sulfurous acid.

Jan 1, 1939

By A. F. Baker

The Bureau of Mines conducted pressure-drop studies in a 4-foot-diameter simulated blast furnace shaft to compare anthracite metallurgical briquets with coke and formcoke. The test materials were used alone, layered, and in mixed burdens of commercial fuel-to-ore ratios. Anthracite briquets had a higher pressure drop per foot than furnace coke, but they had a lower pressure drop per foot than formcoke. This appears to be due to packing and shape, as well as to particle size. The superficial air velocities at which beds of briquets and furnace coke disrupted were about the same. However, if briquets of the shapes and sizes tested are substituted for furnace coke in commercial metallurgical furnaces, higher blowing pressures will be required to deliver comparable amounts of air. Test burdens with more than 5 percent material smaller than 1/4-inch diameter showed significant increases in resistance to airflow.

Jan 1, 1967

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By E. J. HOFFMAN, L. A. SCHOLL, J. c. W. FRAZER

The danger from coal dust in mines has been thoroughly demon- strated by experiment, and consequently the study of the inflam- mability of coal dust suspended in air, that is, the readiness with which a cloud of coal dust inflames, is of decided importance to those engaged in coal mining. Much knowledge has been gained from the work done in the large galleries constructed at official and semiofficial stations in this country and abroad, but the study of the coal-dust problem in these galleries requires so much time and is so costly that there is need of a reliable laboratory method for obtaining a classi- fication of the great variety of dusts that occur in mines. The investigation described in this paper was an attempt to devise such a method. It was a preliminary investigation, and work in the same direction is being continued by the Bureau of Mines. As Mr. Frazer has severed his connection with the bureau, it is deemed advisable to publish the results of his study substantially as he prepared them, with little attempt to draw conclusions or to show the bearing of the results on other studies now in progress. The results of these studies and a full discussion of the significance of the laboratory investiga- tions will be published in future reports of the Bureau of Mines. The reader should remember that any laboratory method, since it involves conditions that differ so greatly from those of actual mining, should be thoroughly tested, and the results obtained by it should be confirmed by experiments conducted on a scale simulating mining conditions before final conclusions are drawn. The need of a laboratory method has long been felt, and several investigators have devised apparatus and methods. The work done by Vital, Holtzwart and Von Meyer, Bedson and Widdas, Le Chate- lier, and that of the British Coal Dust Commission is of great interest in this connection. Bureau of Mines Bulletin 20 contains a sum-

Jan 1, 1913

By John Zetterstrom

Increased activity in the beneficiation of taconite, particularly the magnetic variety, has shown the need for more information on the rate of oxidation of magnetite to hematite. This oxidation occurs in the pelletizing step of the beneficiation process. Magnetic taconite is an intimate association of magnetite and a siliceous gangue. It must be ground to approximately 70 to 30 percent minus 325 mesh to liberate the magnetite from the gangue. With sufficient liberation, magnetic concentration will yield a product high enough in iron and low enough in silica for blast-furnace use. The magnetic concentrate must be agglomerated before it can be used in a blast furnace. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron-oxide materials, sintering and pelletizing being the two most common methods. Sintering is clone on a Dwight-Lloyd or Greenawalt sintering machine. Pelletizing consists of balling fine, moist oxide in a rotating drum, followed by baking at .a temperature below that of incipient fusion to develop a permanent bond within each pellet. The magnetic concentrate from taconite is too fine for good sintering practice but fine enough for good pelletizing practice.

Jan 1, 1950

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

On July 1, the Bonneville Power Administration announced a 25% power cutback because of lower than normal stream flow. In September, the Aluminum Company of America (Alcoa) announced plans to shut down one 23,000-ton-per-year potline at its Vancouver, Wash., primary aluminum smelter. Alcoa also announced that the last of four potlines at its Point Comfort, Tex., primary aluminum smelter would be restarted in October. A new 3-year contract was signed and workers at three Alcan Aluminum Ltd. primary aluminum smelters in Canada returned to work. It was estimated that it would take about 3 months before the smelters were operating at full capacity.

Jan 1, 1979

The Bureau of Mines has long been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts, the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions1 issued by the Bureau of Mines, and the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. The Government, with the exception of the Tennessee Valley Authority, purchased approximately 5.5 million tons of coal in fiscal year 1971. In connection with these purchases, the Bureau analyzed 4,366 samples. These are published (table 1) for the use of Government officials and the public. Such analyses of delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1972

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By L. E. Schultze

As part of the Bureau of Mines research program on recovering alumina from domestic resources, methods for extracting iron from aluminum sulfate solutions (obtained by leaching kaolinitic clay with dilute sulfuric ,acid) were investigated. In countercurrent extraction experiments at a l-gal/hr flow rate of aluminum sulfate leach liquor, the iron concentration 'was decreased from 1.4 g/l to 0.01 g/l after four stages of using a primary amine extractant. The iron-loaded amine solution was regenerated in five stages using 3[N] sulfuric acid or in four stages using 6[N] sulfuric acid. The aluminum sulfate solution obtained was suitable for the preparation of alumina meeting cell-grade standards of less than 0.01 pct iron.

Jan 1, 1979

By Staff

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975