Search Documents

By Graham W. Marks, Clyde A. Bridger

"INTRODUCTION An electrolytic process for the preparation of metallic cobalt has been developed recently in the Bureau of Mines Experimental Station at Boulder City, Nev. Chemical analysis shows this cobalt to contain impurities in small percentages, chief of which is nickel. It is desirable to be able to determine these impurities spectrographically. This report is concerned with a procedure for the spectrochemical determination of nickel in cobalt.Previous spectrographic work on cobalt was done by Breckpot and Mevis,/ who used the method of homologous pairs of lines. However, it was felt that a more detailed investigation was needed, employing the method of internal standards.ACKNOWLEDGMENTWe are indebted to B. G. Knickerbockor and his staff at the Boulder City, Nev., station of the Federal Bureau of Mines for their cooperation, and particularly to Richard W. Lewis and Robert G. Sanderson, who prepared nickel-free electrolytic cobalt for us."

Feb 1, 1948

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965

By L. C. IlsLey

The United States Bureau of clines has been conducting Investigations of electrical equipment during a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 2C, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By Tobias W. Goodman, George N. Aul, Joseph Cervik

The Bureau of Mines conducted research to degasify a virgin block of coal in the Beckley Coalbed using long horizontal holes drilled in an array from the bottom of a ventilation air shaft. Eight horizontal holes and an in situ pressure hole were drilled in a radial pattern to depths ranging from 418 to 910 ft (127 to 277 m) and 205 ft (62 m), respectively. The investigation showed the shaft was in a basin saturated with water, which resulted in low gas flows from holes. The in situ pressure at 200 ft (61 m) into the coalbed was 79 psig (544.6 KN/m2). The aver- age gas and water flows for the eight holes were 94,100 ft3/day (2,665 m3/day) and 13 gal/min (49.3 l/min) . After 514 days of degasification, 18.7 million ft3 (0.53 million m3) of gas had been drained. Methane face emissions, which were measured as a section advanced toward the shaft, were reduced about 77 pct, emphasizing the value of drainage by this technique. All holes were grouted before the area around the shaft was mined.

Jan 1, 1982

By L. K. Barker

The purpose of this research was to determine how much, if any, improvement would be made by subjecting hydrogenated shale-oil naphtha to a catalytic reforming process. Preselected ranges of temperature and pressure within the commercial reforming ranges were chosen for investigation and other possible variables were held constant. All tests were made with a liquid hourly space velocity (LHSV) of 3 volumes of liquid feed per volume of catalyst per hour (Vf/Vc/hr) and a hydrogen feed rate of 3,000 scf/bbl. Operating temperatures of 850°,875°, and 900° F were used at pressures of 200,400, and 600 psig. The greatest octane improvement in the naphtha was obtained at a temperature of 900° F and pressure of 200 psig. The reformed naphtha had a clear research octane number of 89, a liquid yield of 80 vol pct, and a yield-octane number of 71.1. The data indicate that a higher temperature could have produced a higher yield-octane number.

Jan 1, 1973

By Richard F. Hewlett

The purpose of this Bureau of Mines paper is to provide the mineral industry with current information on high-speed data processing and to illustrate how some of these techniques can be applied to the industry. The need for applying these techniques is generally recognized, but not much information is readily available on specific applications. This paper briefly describes high-speed data processing and reduction equipment in an effort to familiarize the reader with the functions of the equipment. A list and explanation of some of the possible applications of high-speed data processing for the mineral industry are included. A few of these applications are illustrated by the use of specific examples of existing computer programs or processing methods, including their calculation times and costs. Some of the programs cited herein were developed by the author at the University of Arizona for a Masters thesis in mining engineering. When a reference is made to a specific computer, the reference is given to make the information that is being presented as factual as possible; most of the manufacturer's equipment that is mentioned in the references was available at the University of Arizona, and no specific endorsement of that manufacturer is intended.

Jan 1, 1962

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By X. Shi, N. S. Dala, V. Vallaythan

"Cellular damage induced by silica dust is known to be associated with increased fragility and destabilization or destruction of the cell membranes. The mechanism by which silica dust effects biological membranes is still unknown. Using the ESR spin-trap methodology, we find that hydroxyl radicals are generated in aqueous suspensions of freshly ground silica. The amount of the radicals generated depends on the extent of grinding and ""freshness"" of the dust. Using linoleic acid as a model lipid, we show that the silica dust causes lipid peroxidation via ·OH, 02-, or linoleic acid related radicals as intermediates. Catalase and superoxide dismutase inhibit the formation of these radicals. The results suggest that free radicals associated with freshly ground silica and the related lipid peroxidation of the memberanes may be the starting point of the silicotic processes.INTRODUCTIONDespite considerable-effort over the years, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrosis are still not fully understood (1,2). It is generally thought, nevertheless, that the interaction of the quartz particles with the cell membranes is the starting point of the silicotic process (3). We felt that the mechanism of the membrane damage by quartz might involve oxygenated free radicals because (a) a suspension of quartz particles in contact with alveolar macrophages has been reported.(4,5) to initiate an enhancement of lipid peroxidation, defined broadly as the ;oxidative deterioration of polyunsaturated components of lipids, and (b) hydroxyl (·OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (6) and initiating lipid peroxidation in lysosomal membranes (7). Moreover it is known that exposure of cell membranes, fatty acids and unsaturated food oils to ionizing radiation, which generates ·OH. radicals, causes rapid peroxidation (6). Earlier studies o~ the aqueous chemistry of quartz suspensions have reported detection of HzOz (8), implicating the formation of ·OH radicals as transient species, but, we are not aware of any report of the detection of ·OH radicals in quartz suspensions and this provided the motivation for the present undertaking. Since it is known that, because of their high reactivity (hence short life time) in aqueous media, the ·OH radicals cannot be detected via electron spin resonance (ESR) directly (9,10), we have used ESR combined with the spin-trap methodology (9) for studying the •OH formation."

Jan 1, 1988

By A. J. Miscoe, W. M. McKewan, J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two 2 in-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine. These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope Lo determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 1992

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

Bitumninous and semianthracite coal reserves underlie about 1,400 square miles of Arkansas, less than 2.7 percent of the state's total area. These deposits, located near the western border, contain an estimated 2.2 billion tons, of which about half are recoverable. This represents less than one-tenth of one percent of the national reserves. Most of the commercial coal is mined from thin beds that are at least 14 inches thick. In some locations, however, the coal beds can be as much as eight feet thick. Lignite was mined in southern Arkansas before the Civil War. Current estimates indicate that the reserves may be as high as 9 billion tons, which could be used in the state's coal-fired electric generating plants; however, these deposits are not being mined at present. Because many coal operations in Arkansas are small and the demand for coal is unsteady, the industry employs fewer than 25 miners on a daily basis. Arkansas gained primacy when its regulatory program was conditionally approved November 21,1980, subject to the correction of four minor program deficiencies. The regulatory program was fully approved January 22, 1982. Authority of the state to administer its Abandoned Mine Land Reclamation Program was granted upon approval of the Arkansas Reclamation Plan on May 2, 1983. Arkansas was the first state to assume responsibility for abandoned mine land emergency projects when its Reclamation Plan was approved.

Jan 1, 1992

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By J. J. Lukasko

The U.S. Bureau of Mines developed an alternative electrochemical process for the production of calcium metal. The current industrial practice is costly, complex, and inefficient. The Bureau method involved electrowinning of a calcium-tin alloy followed by electrorefining to produce calcium metal. In the electrowinning cell, CaCI2 was fed to a KCI2-CaCI2 electrolyte. The calcium was electrowon at 6500 C into the pure molten tin cathode until the cathode contained 7.5 wt pct Ca. Current efficiency for electrowinning averaged over 90 pct. The resulting calcium-tin alloy served as the anode for the electrorefming cell, which employed a [CaC~-CaF2] fused salt as the electrolyte. Calcium metal was electrorefmed at 8500 C with a current efficiency of 85 pct based on calcium metal recovered. The calcium metal analyzed 99.2 pct, which is purer than commercially produced calcium.

Jan 1, 1990

By H. Dale Nichols

[The growing importance of the Sundence (Jurassic) formation an a source of oil, in the Rocky Mountain area has prompted the making of a series of porosity determinations of core samples collected. from the reservoir sands of the Lance Creek oil field, Niobrara. County, Wyo. These analyses are preliminary to a stud of fluid and energy relations in the Basal Sundance reservoir of that field, and the determinations of porosity will be used in subsequent studies requiring, calculations of the volumetric capacity of the reservoir and estimation of the reserves of oil and gas. However, the porosity characteristics an of the Sundance sands in the Lance Creek field are factory that affect the solution of many current practical problems of development and operation. Primarily for that reason but also because it is recognized that porosity values of different oil-production sands are of widespread interest throughout the industry, the results of the initial work have been presented in tabular and graphic form with no attempt to evaluate their significance as they relate to the production history of the field.]

Jan 1, 1938

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By J. B. Janus

This report, the 25th in a series, lists analytical data of coal samples collected by the Bureau of Mines in connection with the purchase of several million tons of coal for various Government agencies during fiscal year 1975. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for these coalbeds only. The delivered coal was sampled at destination in accordance with instructions furnished by the Bureau of Mines, and all samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1976

By A. Sainato, S. J. Kravits, G. L. Finfinger

This report describes a project conducted by the Bureau of Mines in which the accurate directional drilling of a borehole was demonstrated with the objective of intercepting a designated target. The project was conducted at Navajo Dam in northern New Mexico at the request of the Bureau of Reclamation. Borehole survey and drill logs are provided in an appendix. The trajectory of the demonstration borehole was designed to intercept a 5-ft-radius target at the final or "punchout" distance of 885 ft. The elevation of the borehole at this distance was within the target; the borehole punchout coordinates were 8.81 ft southwest of the target. As a result of the demonstrated accuracy, the Bureau of Reclamation has contracted the accurate drilling of boreholes as long as 600 ft from the inside of a short tunnel, to control water seepage in the right abut- ment. This resulted in a substantial cost savings compared to the orig- inal plan of constructing a longer tunnel and drilling 150-ft boreholes.

Jan 1, 1987

The Tenth International Conference of Directors of Safety in Mines Research was held in the United States from September 28 through October 2, 1959, at Hotel Webster Hall, Pittsburgh, Pa. The Conference was organized by the Federal Bureau of Mines. In accord with the program outlined at the Ninth Conference (1956, Heerlen, Holland), the papers submitted dealt with the following three subjects: 1. Safety of coal mine explosives 2. Explosion hazards in mines 3. Ignition and fires in mines Seventy papers were presented. There were eight technical sessions followed by an extended tour of the Bruceton facility of the Bureau of Mines on October 2. Simultaneous translation was provided in the three official languages of the Conference--English, French, and German.

Jan 1, 1962

By R. D. Leitch, J. G. Calverley

"INTRODUCTION Although many investigators have provided information on the strength and other properties of concrete the published literature cites few data on the effect of mixing cement with acid mine waters or on acid resistance of concrete in contact with mine waters. Most of the reported work on the effect of impure waters has dealt with the resistance of cement specimens to ""sulfate waters,"" that is, waters or soils with a relatively high sodium sulfate content. The ""Merriman test"" is used commonly to determine the corrosion resistance of cements for 28 days, but it does not seem certain that a cement having a high sulfate resistance in the Merriman or similar tests necessarily will show correspondingly great resistance to the sulfates of iron and, particularly, to sulfuric acid, which usually are present in acid mine waters. Extensive use of cement mortar for laying up masonry stoppings in coal and other mines and for constructing concrete mine haulageways and shaft linings, coal-storage and other retaining walls, highway bridges, culverts, and many other types of construction where it is difficult to obtain fresh water for mixing or where the structures are later exposed to contact with acid waters makes it important to know the effect of these conditions on cement and whether there is a cement better suited for such work than ordinary portland cement.CONDUCT OF THE INVESTIGATIONFor a short time early in 1935 the opportunity to obtain at least some additional information on the effect of acid mine water on cements was presented by the Relief Works Division, which provided money for irregular and indefinite employment for several months. Purchase of apparatus or material was not permitted under this arrangement, and indefinite duration of the work, intermittent employment, and finally complete cessation of the work prevented planning for extensive investigation of this particular problem."

Jan 1, 1940