Search Documents

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

Tailings embankments can develop a high phreatic surface if the original design for the embankment does not include drainage facilities or if existing drainage facilities become ineffective. Subsequent raises can develop a seepage surface due to a high phreatic surface that can lead to stability problems. The U. S. Bureau of Mines amended contract J0100013 to initiate this study of horizontal drains in tailings embankments. This study developed a technique for determining the length of and spacing between parallel drains through the use of the finite element model UNSAT2. The analysis is based on the combined output of a vertical planar mesh and a horizontal planar mesh. The slot opening in the drain pipe and the length of the perforated section are determined from an analogy to water well design. The pipe diameter and gradient can be determined from Manning&apos;s equation. To the authors&apos; knowledge, this is the first attempt at horizontal drain design using a finite element model. Additional research is recommended in this area.

Jan 1, 1982

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,857 samples, representing the products of 103 companies. The samples were collected during June, July, and August 1955. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1956

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nonmetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By C. R. Nisewanger, F. W. Brown

"The velocity of detonation of an explosive is one of its most important properties, because its performance depends markedly on the rate at which it releases its energy. Fortunately, the velocity of detonation is one of the few properties of an explosive that can be measured precisely. However, the velocity of detonation of an explosive may depend on several factors other than its chemical composition, such as density, physical state, degree of confinement, nature of confinement, and magnitude of initiating impulse. Presumably for an explosive of fixed chemical and physical properties there are certain limiting conditions of confinement and initiation under which the explosive will detonate at a maximum constant and uniform velocity. This velocity is its ""ideal"" velocity of detonation. It is obvious, however, that in order to evaluate performance properties of an explosive in all of its applications it may be necessary to measure its velocity of detonation under a number of conditions in which the velocity of detonation is far from the maximum ""ideal"" velocity.. Under certain-conditions the velocity of detonation may even,be,different at different points in the explosive.It is .relatively simple to determine the velocity of detonation of an explosive under a. standard set of conditions if one is free to use large quantities of the explosive and to form it into a convenient shape. Under these circumstances; one can use a thin column of explosive a meter or more in length. The time required for an explosion to travel the length of the column will not be less,of the order a few ten-thousandths of a second and can be readily and accurately measured .by means of the standard spark chronograph or by photographing the explosion with a rotating-drum camera. However in many applications the explosive charge may be of relatively small dimensions arid may not be in a form convenient for making velocity measurements and often may be enclosed in a case or other confining medium. It may be necessary to determine the velocity of detonation over distances of the order of a few centimeters, in which case the time intervals to be measured will be extremely small. For example, the time required for an explosion to traverse 1 centimeter of tetryl is of the order of 1.5 microseconds.Since no satisfactory method of determining time intervals of the order of magnitude of a few microseconds within an explosive charge was available,, at least not for all conditions that might be encountered in practice, it was necessary to develop a special electronic chronoscope which is capable of measuring time intervals as small as a microsecond with a fair degree of accuracy. This report describes the chronoscope and its application to measurements of velocities of detonation in explosives."

Mar 1, 1946

By H. H. Schrenk, L. B. Berger, W. P. Yant, F. A. Patty

"The use of small such as canaries and white mice, for detecting carbon monoxide depends primarily on the fact that the volume of respiration of these animals in proportion to their volume of blood is much higher than for man. Accordingly, when animals and men are simultaneously exposed to a given concentration of carbon monoxide the animals will absorb it more rapidly and attain serious poisoning in less time than men. Prom a practical viewpoint the use of the animals depends on the margin of time between observable symptoms in them and serious poisoning in man, during which man can return to fresh air or use respiratory protection. It should be remembered, however, that during the time the animal is incurring a detectable degree of poisoning, man is also absorbing some carbon monoxide, and the margin of time is not very wide. Experience with canaries has shown that an occasional specimen may have a tolerance above the average of the species and fail to exhibit symptoms before man incurs a very discomforting and possibly a serious degree of poisoning.It is also well known that physical activity increases the demand for oxygen by the body, and the respiratory exchange and circulation of the blood are increased to meet the demand. This sets up a vicious condition if carbon monoxide is present in the air because the rate of absorption of carbon monoxide is not only increased by the increase in respiration and circulation, but the absorption of carbon monoxide decreases the capacity of the blood for carrying oxygen at a time when the demand is high. These facts, together with the increase in respiration and circulation which attend excitement, underlie the caution to be calm and to walk slowly and to reduce physical exertion to a minimum when exposed to carbon monoxide. For these same reasons, when using animals for detecting carbon monoxide it is endeavored to keep them active, thereby tending to increase the response of the birds and widen the time between observable effects in the birds and effects in the man. As rule canaries are kept fairly active through fright at the unnatural surroundings and in their endeavor to remain on the perch of the cage when carried into the atmosphere to be examined. They also experience an excitement stage with oncoming carbon monoxide poisoning. Sometimes, however, especially if the air is cold, they tend to be inactive and quiet. Ordinary mice and white mice become inactive with use and also with oncoming poisoning. They huddle in the corner or the cage, and thereby not only reduce their sensitivity but make it difficult to observe signs of poisoning."

Oct 1, 1930

By Sean Gallagher, Rhys Llewellyn, Jay Mattos

This paper contains the results of an examination of accident, injury, employment, and production information reported to the U.S. Department of Labor&apos;s Mine Safety and Health Administration (MSHA) and provides information on some of the measures longwall mine operators are using to prevent accidents In all industries, technological advances play a key role in determining those who will survive as competitive participants in an increasingly global marketplace. While mining is among the most basic of industries, technological change is neither unfamiliar nor unwelcome to miners. Historically, technological advances in mining, particularly coal mining, have tracked closely with fluctuations in demand. In the early 1900&apos;s, coal accounted for more than three quarters of all the fuel consumed in the U.S. To meet this tremendous demand, underground cuffing machines were introduced, resulting in faster, more efficient coal extraction. Transporting coal to the surface, however, remained labor intensive. In the 1920&apos;s, nearly all underground coal was still being hand loaded. Demand for coal then declined as the price of oil, natural gas, and electricity became competitive. In the late 1930&apos;s and throughout the duration of World War II, coal demand and production was high. By 1940, more than half the coal mined was being mechanically conveyed to the surface. In 1948, the continuous mining method was introduced in the U.S., further accelerating the extraction process. By the 1950&apos;s and 1960&apos;s, however, coal production again declined as railroads converted to diesel fuel and gas and oil provided a larger share of the home heating market. Underground coal mines required even more mechanization to remain competitive as an energy source. The first longwall system was introduced in 1960. By 1995, longwalls were producing more than 189 million tons of clean coal annually, surpassing continuous mining production for the second straight year. The mining of coal and other materials has not come without a huge loss of life and considerable human suffering. More than 103,000 workers died from injuries in U.S. mines in the last 85 years. Between two and three thousand miners died each year from the turn of the century until 1931, many from underground fires and explosions. The U.S. has witnessed a tremendous drop in fatalities in underground coal mines. Credit for that is due to safety inspections and enforcement activities, better safety awareness and practices among management and labor, improved ventilation, the use of safer equipment, and increased mechanization which removed many miners from the hazards at the face and also reduced the size of the mining work force. There is little doubt that longwall mining has greatly increased underground coal mine productivity. The degree to which longwall mining has contributed to a safer work environment for underground miners is more difficult to ascertain.

By R. O. Dannenberg

This Bureau of Mines report describes the results of research to develop a process for recovering additional beryllium from a commercial mill waste product, fluoferrate leach residue. Forty-five percent of the total beryllium in the leach residue was recovered in a beryllia product assaying over 98 pct Be0 by a process comprising (1) leaching with 1 N sulfuric acid, (2) adjusting the acidity of the leach liquor to pH 2, (3) extracting the beryllium with di-2-ethylhexyl phosphoric acid (EHPA), (4) stripping the loaded extract with sodium hydroxide solution, (5) boiling the sodium beryllate strip solution to precipitate beryllium hydroxide, and (6) calcining the beryllium hydroxide. Calculated reagent requirements per pound of Be° recovered by a proposed flowsheet were 28.1 lb sulfuric acid, 0.04 lb flocculent, 0.15 lb EHPA, 0.06 lb isodecanol (IDA), 0.22 gal kerosine, and 6.3 lb sodium hydroxide.

Jan 1, 1966

By J. E. Rourke, O&apos

A wide variety of techniques and equipment are available for coring soft or poorly consolidated geological material. This report presents a comprehensive literature review and evaluation of these techniques and equipment. A potential user will find guidelines in this report to assist him in selecting sampling equipment. A bar chart shows what samplers have been used under what geological conditions, and gives the specific literature references. Two matrices rate the present techniques and equipment with respect to reported success for sampling specific materials, and with respect to several performance characteristics including complexity of use and core quality. These matrices are supplemented with tables of typical sampling equipment. and program costs. Near-term future developments are seen primarily in improved training of drillers, and in instrumenting the drilling operation to provide objective data on drilling characteristics. An extensive annotated bibliography, a catalogue of equipment suppliers including specifications and cost ranges, and a list of manufacturers and distributors are appended to the report.

Jan 1, 1978

By J. Douglas Causey

In 1986 and 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 73,010 acres of the 76,480-acre Lower Owyhee Canyon Wilderness Study Area (OR-003-110) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 8 miles north of Rome. There are approximately 7.7 million tons of subeconomic zeolite (heulandite and/or clinoptilolite) resources with ammonia ion exchange capacities as high as 1.75 milliequivalents per gram in the Chalk Basin-Lambert Rocks area. The bed is 25 ft thick with less than 100 feet of overburden. This resource probably will not be mined in the foreseeable future.

Jan 1, 1989

By H. H. Fields

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot-deep vertical borehole¬. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmos¬phere, the total gas and water flows and the in situ pressure dropped, respec¬tively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the correspond¬ing values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By E. Concha

The concept of an Automated Continuous Explosive Excavation system (ACEE) for the underground mining applications of development drifting and room and pillar mining has been evaluated in comparison with conventional drill, blast and muck operations. The role and possible extent of application as this method was identified. The evaluation examined each element of existing and of proposed ACEE design concepts in a defined mine environment. Step by step procedures were developed to quantify the evaluation process where this appeared feasible. One conclusion drawn was that a system approach to ACEE design is not only feasible but attainable within the state of the art. Several preliminary design concepts were formulated and examined in order to determine what further research or development might be needed to realize them.

Jan 1, 1982

By Robert G. Lundquist

The Bureau of Mines compared longitudinal strain energy output of a percussive drill to energy determined by measuring maximum piston velocity. Strain gages were used to determine the strain-time waveform and its amplitude at seven levels of operating pressure and eight levels of thrust. The longitudinal strain energy was found to be approximately 14 ft lb less than the maximum piston energy at comparable operating conditions.

Jan 1, 1969

By K. J. Miller

A laboratory electrophoresis column was designed to separate pyrite from fine coal by utilizing an observed difference in the electrophoretic mobilities of the two materials in water. The apparatus worked well when tested with synthetic mixtures of coal and pyrite, but some modifications in design and procedure were necessary to provide a sharper separation. After these changes were made, the column was tested with a high-pyritic-sulfur raw coal sample. The column successfully fractionated the sample, removing not only the pyritic refuse, but a siliceous refuse as well. The invest ion demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis.

Jan 1, 1970

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

By R. S. Dean

In general, the Division conducts investigations relating to the treatment of ores and metallurgical products from the condition to which they are mined to the refined metal. At the object of conserving natural resources and eliminating waste by furnishing information on current methods of metallurgical practice making fig fundamental studies of metallurgical processes and developing new processes and alloys to the point of demonstrating their or value. Office of the Chief Engineer The functions of the technical units of the Office of the Chief Engineer are indicates

Jan 1, 1941