Search Documents

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity. On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can not be designed to be 100 per cent efficient and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the computed figures of heat requirement per carrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, 'the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil.

Jan 1, 1931

By N. Malakondaiah

Several growth chamber and laboratory experiments were conducted to study the germination behavior of plant species on mine spoils and plant growth responses to nutrients on spoils and topsoils. Experiments were conducted to study the germination potential of some native and introduced species under various conditions. The seeds of green needlegrass, side oats grama, thickspike wheatgrass, crested wheatgrass, birdsfoot trefoil and emerald crownvetch were less tolerant, whereas those of alkali sacaton. durar hard fescue, slender wheatgrass, yellow sweetclover and alfalfa were most tolerant to the sodic mine spoil conditions. Addition of leonardite improved the germination potential of some of the poor genninators. Slender wheatgrass and yellow sweetclover were used as test plants to study the fertility status and productivity potential of stockpiled topsoils and spoils collected from Center. Glenharold and South Beulah of North Dakota. The topsoils were neither saline nor sodic but low in N and P. The spoils were neutral to alkaline with SAIL of 12-32, EC of 1.8-5.5 mmhos/cm, Olsen&apos;s P< µ4g/g, and total N <0.07%. Application of N and P together to the topsoils increased the yield of wheatgrass and sweetclover by 88% and 70% of their respective maximum yields, whereas near maximum yields were obtained for both the species by the same treatments to the spoils. The average yields on topsoils were higher than the yields on spoils. The concentrations of major nutrients were higher in plants grown on topsoil, whereas the opposite was true with the concentrations of Mn, Zn, and Cu. Growth chamber experiments were also conducted to study the growth responses of alfalfa, oats and slender wheat grass by the application of Mn and Zn to a sodic coal mine spoil which was previously used for pot culture experiments. Significant growth responses to Mn and Zn were observed in alfalfa but not in oats or slender wheatgrass. Fertilizing the spoil with Mn along with NPK increased the yield of alfalfa to 85% and with Mn + Zn to 99%. Growth responses and plant composition results of this study confirm that the application of major nutrients to spoils can accentuate Zn and Mn deficiencies in some plants.

Jan 1, 1982

By Robert W. Ageton

Optimal planning for mining the deep, lead-zinc-silver deposits of the Coeur d&apos;Alene mining district, Shoshone County, Idaho, could be facilitated by a knowledge of the magnitude and direction of the pressure acting in the virgin rock. The distribution of primary stresses should be considered in order to prevent possibly destructive mining-induced stress concentrations. This particular investigation was concerned with determining stress in a zone 4,000 feet below the surface and known to be ender stress concentrations due to mining operations. Disking of the stress-relief cores obtained in a vertical down hole permitted qualitative evaluation from visual observations; the results indicate that a high lateral stress existed at the time the measurements were made. Stress-ellipsoid determinations gave a compressive principal stress of -13,000 psi oriented about N 45° W and nearly horizontal, a compressive principal stress of -11,000 psi oriented about S 45° W and abut 60° off the vertical pointing away from the vein, and a compressive principal stress -5 -7,000 psi oriented N 45° E and about 60° off the vertical, pointing toward the vein. Subsequent to the overcoring stress-relief drilling, a rock burst occurred about 100 feet northwest of the test site.

Jan 1, 1967

By Michael P. Moore, Christopher J. Rise

"Over the past twenty years, there have been numerous studies which have attempted to correlate the prevalence of Coal Workers' Pneumoconiosis (CWP) with different characteristics of the coal seam. Some investigators have tried to find a relationship, or the lack of a relationship, between the rank of coal seams and the incidence of CWP. Others have attempted to show that there is a positive correlation between the mean mass of respirable dust in the mine atmosphere and the prevalence of CWP. Still others have tried to determine the influence of the quartz content of respirable dust on the incidence of CWP. Unfortunately, many of these different investigations have conflicting conclusions.One area of research with conflicting conclusions deals with the relationship between the rank of the coal and the incidence of CWP. For example, an inves¬tigation conducted in Pennsylvania and West Virginia coal mines concluded that the prevalence of CWP increases with an increase in coal rank (1). A study in Great Britain also observed a close relationship between the rank of coal and the prevalence of CWP (2). However, another study involving 312 Appalachian coal miners concluded that the association between coal rank and CWP might be fortuitous and that other factors may be more important (3). In addition, an investigation involving 2,600 miners during a period of twenty years in Great Britain established that there is only a weak correlation between the prevalence of CWP and the rank of the coal (4). Consequently, it appears that there is still uncertainty as to whether or not the rank of the coal seam has an influence on the development of CWP.Another area of investigation concerns the relationship between the mean mass of respirable dust present in the mine atmosphere and the prevalence of CWP. A study involving 4,122 miners over a period of ten years in Great Britain noted a high correlation between the mean mass of respirable dust and the incidence of CWP (5). Another investigation involving 3,154 British face workers con¬cluded that the overall mass of respirable dust is the factor most closely related to the ten-year attack rate of CWP (6). However, a study conducted in thirty-one mines in the United States concluded that it is doubtful that the quantity of respirable dust alone is responsible for the difference in the prevalence of CWP (7). Even though there are conflicting conclusions, there are many more investigators who confirm, rather than deny, the relationship between the mean mass of respirable dust and the development of CWP.The third subject of investigation is the role of quartz in the incidence of CWP. For example, two studies in Great Britain concluded that the quartz content in coal mine dust has no relationship to the prevalence of CWP (8,9). But a study involving 312 Appalachian coal miners revealed that the level of exposure to free silica plays an important role in the development of CWP (10). Once again, the conclusions reached by different researchers are conflicting.Probably the most important factor in the discrepancy among the studies is the variability among different coal mines. A mine operating in an inherently ""dusty"" seam may have a low concentration of respirable dust while a mine operating in a less dusty seam may have a high concentration of respirable dust. This discrepancy is a result of variables such as the effectiveness of ventilation or the efficiency of the water sprays. Consequently, it is very difficult to compare the dustiness of different coal seams by in-mine measurements of the respirable dust concentration. A laboratory test would more accurately characterize a coal seam according to its respirable dust production."

Jan 1, 1988

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961

By D. F. Reed

As a part of a comprehensive survey of the Adirondack region, the Bureau of Mines, 1944 and 1945, conducted investigation of magnetic deposits at Dennemora, Russia Station, Redford-Clayburg, Standish, and the Ausable river region. Later in 1945, the Federal Geological Survey, started an aeromagnetic survey of the area and completed it in .1946. The Bureau of Mines extended its magnetic surveys in 1946 in the Redford-Clayburg area. In 1947 the Bureau of Mines .diamond-drilled throe holes in the Redford-Clayburg district. Clinton County has one active magnetite mine at Lyon Mountain and inactive mines at Palmer Hill and Arnold Hill, as well as along the Saranac River.

Jan 1, 1949

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

By Jon C. Volkwein

The canopy-air curtain was originally developed by the Bureau of Mines to surround the operator of a continuous mining machine with a zone of clean air. This report describes the application and testing of a canopy-air curtain on a gathering-arm loader, as well as some of the problems associated with providing a zone of clean air to a standing, semimobile operator. The area of air-curtain coverage and effects of air velocity are discussed. In its present form, the canopy-air curtain provides a 50 percent reduction in respirable dust to the operator.

Jan 1, 1981

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By David R. Peterson

This user&apos;s manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user&apos;s manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By W. W. Weller

This report provides low-temperature heat-capacity data and entropies at 298.15° K. for magnesium metavanadate (MgV206) and magnesium pyrovanadate (Mg2V207). The work completes low-temperature measurements planned for alkaline-earth vanadates; an earlier report dealt with calcium vanadates.4 No similar data for these compounds have been published previously. Free energy of formation values at 298.15° K. were derived by combination of the present entropy values with heat of formation data. MATERIALS The materials used in the measurements were portions of the samples described in a previous Bureau of Mines publication by King, Koehler and Adami.5 Methods of preparation, chemical analyses, and X-ray examinations are covered in this paper. The indicated purity of the samples was 99.9 pct.

Jan 1, 1962

To improve a miner&apos;s chance of survival during an emergency by providing immediately avail-able breathable air and protection from toxic gases until a longer-duration breathing apparatus, stored nearby, can be reached. Approach: A belt-carried apparatus which can provide a closed-circuit atmosphere for ten minutes breathing has been developed under a Bureau of Mines contract. How It Works: Water vapor and carbon dioxide in the user&apos;s exhaled breath are removed, and oxygen is supplied, by chemical reactions. When the user exhales into the mouthpiece, water vapor in his breath reacts with potassium superoxide (KO2) stored In the canister to produce oxygen. The other product of this reaction (KOH) reacts with carbon dioxide and removes it from the air. The oxygen-enriched air then flows from the canister into two breathing bags. When user inhales through the mouth, that air is drawn out of the bags, makes a second pass through the chemical-containing canister, and flows into the mouthpiece tube. A nose clip is worn to seal off the nasal passages.

Jan 1, 1975

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation&apos;s mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By John R. Bartels

This Bureau of Mines report describes the development of a preliminary design for a novel, protected, cab-shuttle car for use in working seam heights down to 40 in. Because of the severe restrictions imposed by low-coal operation, Mine Safety and Health Administration (MSHA) regulations only require canopy protection on shuttle cars operating in seam heights of 42 in or greater. MSHA routinely grants variances for canopy use in seams 48 in high or less. The design was generated by giving the operator needs equal priority as related to machine performance parameters. Cab-shuttle car concepts that led to the recommended design are described, along with criteria and testing used to evaluate their potential effectiveness.

Jan 1, 1988

By Donna L. Anderson

This U.S. Bureau of Mines report describes a system to determine the position and heading of a continuous mining machine during the maneuvers required at the face area of a mine. The system consists of commercially available angular position sensors and a computer interface developed and tested at the Bureau. The sensors employed are laser-based scanning devices that report the angular location of retroreflective targets within their 90° field-of-view. The targets are mounted on the continuous mining machine; the laser scanners are mounted on an external reference structure. The computer interface consists of a single-board computer-controller programmed to gather and process the angular position information, and to calculate the machine&apos;s position and heading relative to the reference structure. A sensor fusion algorithm will be incorporated into the computer interface programming to increase the accuracy and reliability of the system.

Jan 1, 1989

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983