Search Documents

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facilitate research on the fundamentals of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, but Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing adit has an advantage over an active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin in September 1936, with a crew of four laborers under a resident engineer. The laborers were recruited from nearby farms, and although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By R. V. Ramani

Procedures have been developed which permit determining in either existing or new mines the optimum diesel equipment deployment schemes and the effect of. diesel exhaust on mine-air quality. Specifically, the following areas are covered in the report: 1. Description of diesel deployment schemes in four underground coal mines that were visited is provided. 2. Description of the analysis procedure to determine the number of shuttle cars required to maintain maximum theoretical continuous miner (or loader) production rates in typical room-and-pillar mining systems and of exhaust contamination resulting from the deployment of diesel powered shuttle cars are provided. Sensitivity analyses to determine the effect of changes in input variables on production and contaminant concentrations are also discussed. 3. Description of the analysis procedure to develop the locomotive operating parameters is provided. Assessment of both production performance as well as estimates of the magnitude of diesel exhaust contamination of the mine air are also made. 4. Recommendations for extensions of this research are outlined and include developing and testing procedures for 1) determining equipment duty cycles for the diesel equipment, and 2) studying the exhuast contamination of mine air on the basis of these duty cycles.

Jan 1, 1978

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and, flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series con tains a linear hydrocarbon chain containing nine carbon atoms (CH3 ( CH2 )8-C6H4- ( OC2H4 ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight' carbon atoms ( ( CH3 ) 3CCH2C ( CH3) 2-C6H4- ( OC2H4 ) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determine& This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 ] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By J. H. Soulé

"The Copper King copper-gold-silver deposit was discovered about 1880. Various individuals and companies have been interested in the deposit and considerable work has been done, although production, if any, has been small. The deposit is located in the western part of Laramie County Wyo., and is favorably nituated with respect to rail and truck transportation and high-tension power facilities.Mild summers and cold winters characterize the climate. Precipitation averages between 16 and 17 inches annually, with considerable snowfall in the winter. Permanent streams are small and most available water in being stored for use by Cheyenne, Wyo. Range grasses comprise the bulk of the vegetation, with small treed and shrubs common in the most rugged areas.The deposits lie upon land owned by Wyoming, now leased by a group of Wyoming and Colorado businessman constituting the Copper King Mining Co.Primary copper-gold mineralization seems largely confined to an equigranular, relatively fine grained gneiss that is part of a pre-Cambrian complex of metamorphic rocks ranging from schists to pegmatites. The copper minerals are oxidized to a depth of from 100 to 150 feet, with the occasional occurrence of secondary minerals at greater depths. The copper minerals chalcopyrite, malachite, chalcocite, bornite, cuprite(?), and some native copper were observed in Le deposit.In addition to the 4,030 feet of diamond-core drilling in 11 holes done on the deposit by private companies, the Bureau of Mines drilled 3 holes for a total of 2,630 feet. The sample results of this drilling plus available data from previous drilling and sampling are appended to this report."

Jun 1, 1955

By J. Ankrum, T. Xia1, D. Wilder, K. Spratt

The human lumbar spine is inherently an unstable structure and requires sophisticated neuromuscular control to maintain its stability and for performing physical tasks. As a consequence, it is important to understand the potential health effects on human operators of mechanical stimuli such as shock and vibration.1 Impact applied to a vehicle operator combines the risk of sudden, unexpected load with the mechanical stress of the seated posture.2 Because many work environments contain the potential for multiple, unexpected impacts, it is important to understand how the trunk muscles respond to complex conditions. We believe the results have implications for isolation design and standards development. Methods Muscle activity was recorded during simple and complex impacts, applied randomly and without warning, while subjects sat on an air-suspension truck seat located on a man-rated 6-DOF motion platform (Rexroth-Hydraudyne). Simple (single) impacts consisted of 100 ms quarter-sine jolts in the side-to-side (L and R) and vertical upward (V) directions with peak amplitude at 0.4 g. Complex impacts consisted of combinations of two simple (single) impacts in sequence (LV, RV, VL, VR), separated by 100 ms. Twelve right-handed males (23.7 ± 7.8 years old) were tested without a blindfold under 2 posture conditions (supported while leaning back and unsupported, sitting upright) and 2 seat suspension conditions (present or absent). Each type of impact was repeated three times under each posture and suspension condition, resulting in 84 impacts in total. Surface EMG signals from the left and right erector spinae (ES), rectus abdominis (AR), external obliques (EO) and internal obliques (IO) were recorded and transformed to 25ms RMS values. The response time, defined as the time the muscle activity exceeded the mean + 2 STD of the pre-impact resting period, peak response amplitude, and time were then derived. A mixed-model repeated measures analysis of variance was used to evaluate statistical significance, where type I error rate was set at .05. Results One question we asked of these data was whether there were differences in responses related to simple single strike impacts (L, R, or V) and complex, double-strike impacts (LV, RV, VL, VR). There are 21 possible combinations of comparisons of simple and complex impacts to each other. The differences found are listed in Table 1.

Jan 6, 2006

By M. D. Aldridge

The results of a two-year research effort aimed at improving communication systems in coal mines is reported. A review of communication methods presently used in coal mines is presented. Theoretical and-experimental results of a four pronged effort in the areas of (1) through-the-earth propagation, (2) paging system design, (3) improvement of wired telephone systems, and (4) carrier current systems are described. Auxiliary systems not included in the above are considered briefly. Various conclusions are drawn in light of practical constraints and the needs of the mining industry. The study clearly demonstrated the need for nine communications to be designed on system basis. The viability of new technology for providing reliable mine communication for improving mine safety and operating efficiency is shown.

Jan 1, 1973

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment: including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that arc recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel al the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By S. P. Kinney

Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. An example of the result of inefficient gas-solid contact in the shaft of a blast furnace is shown by the curves in Figure 1.

Jan 1, 1930

By O. T. Barrett, R. F. Aberethy, H. N. Cooper, Thomas Fraer, William L. Crentz

"INTRODUCTION The object of the techniques described in this report is to determine the possibilities of separating the components of a raw coal into such grades as may be necessary to recover some exceptionally clean functions for special purposes.To do this commercial gravity methods would require separation at very low specific gravities, entirely outside the range of conventional practice. Hence, a technique has been developed for breaking down cool ample, into very close fractions within the gravity range of the (-lean coal matter as well as for separating it from the refuse and particles.Such data on the fundamental specific-gravity consist of the clean-coal matter will serve to appraise the difficulty of the problem and to chow be accomplished if and when effective methods of making such separations commercially are developed."

May 1, 1945

By Carlton E. Brown

The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted in South Africa about 19164/ and more recently in England5/, 6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting,

Jan 1, 1938

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By Gregory Molinda

NIOSH has recently completed a study of the interaction between polyurethane (PUR) and coal mine roof in order to determine the mechanism of reinforcement, in both highly fractured rock and unfractured rock. Four case studies of PUR rein­forcement are presented. At a West Virginia site, a borehole camera revealed the location of roof voids and guided the PUR injection. By injecting polyure­thane into a zone from 0.6 to 1.8 m (2?6 ft.) high in the roof, a roof beam was created and ongoing intersection falls were halted. In another highly fractured roof in a western Pennsylvania mine, a total of 5.8 cm (2.3 in.) of rubbleized rock was found in a zone up to 3 m (10 ft.) into the roof. Untargeted PUR injection filled approximately 1/2 of the fractures. These two case studies showed that it is not necessary to fill up 100% of the void space to create stability. In the other two field sites, polyurethane was injected into weak, but unfractured roof. Post-injec­tion video monitoring showed that weak bedding planes were hydraulically wedged open and polyure­thane injected along bedding. The reinforcement value of this injection method is limited because of the wafer-thin layer of PUR introduced along bedding, and the lack of a PUR ??webbing?? which would serve as a structural framework to provide strength. It was determined that video inspection prior to PUR injection can aid in identifying the fracture zones to target, and minimize ??blind?? pumping and loss of PUR.

Jan 1, 2008

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection and operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection Paid operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By L. B. Berger

From time to time the Bureau of Mines receives requests for information and advice regarding the safety of using internal-combustion engines operated on butane fuel as prime movers for haulage and other purposes in mining and tunneling. The purpose of this, circular is to discuss the properties of butane and to present data in regard to the possible use of this fuel in underground operations. Published information on the use of commercial butane as a fuel for internal-combustion engines indicates that, insofar as performance is concerned, butane may be utilized satisfactorily and efficiently for this purpose. However, the introduction of a volatile, inflammable material such as butane into confined spares such as mines or tunnels would create potential fire and explosion hazards that should be given due consideration by those concerned with the promotion of safe practices.

Jan 1, 1944

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By A. A. Cochran

The purpose of this Bureau of Mines research was to investigate the theoretical and practical aspects of using ionizing radiation to promote chemical reactions that are of interest to metallurgists, and to carry out a radiation study of a suitable reaction. The effect of 44,000 roentgens per hour of 120,000-volt X-rays on the chlorination of highly pure mixtures of rutile, carbon, and various catalysts at temperatures up to 540° C. is described. At these low temperatures, recoveries were very low; however, in the eight different systems studied, an increase in yield due to X-rays was statistically significant in two instances and was of borderline significance in a third instance. In the other five systems, the differences in yield were not significant. Impurities and added catalysts caused relatively large variations in the yield of TiC14 from the reaction. Although the catalysts employed were reported in the literature as positive catalysts for the reaction, most of them were negative catalysts for the highly pure system studied. With only one exception, each increase in the purity of the charge resulted in a decreased yield of TiCl4. The experimental results indicate that many substances catalyze the reaction studied and suggest that the differences in reactivity of the charge stocks may be due to their various contents of positive and negative catalysts.

Jan 1, 1962

By O. H. Metzger

This is the first of two papers dealing with construction and use of aerial tramways in the metal-mining industry. It describes practices and equipment used in tramway construction and discusses the design of tramways. The second paper will describe the construction and operation of tramways and give operating costs. ACKNOWLEDGMENTS The author acknowledges the cooperation of a number of cable and tramway manufacturers Who supplied practical manufacturing data and other valuable information. Full credit for formulas used in the design of aerial tramways it given' to Edward B. Durham3/ and F. C. Carstarphen.4/

Jan 1, 1937