Search Documents

By S. M. Runke

An earlier Bureau of Mines report4/ reviewed and summarized all reports of investigations dealing with the coarse grained pegmatites of the Black Hills of South Dakota to dune 1951. It was proposed, and the hope was expressed in this report, that future progress in the development of the technology of the mining and beneficiation of the pegmatite deposits would be rapid enough to make it possible to issue annual progress reports. Although notable progress has been made in the treatment of pegmatite material, it has not been rapid enough to justify annual reports

Jan 1, 1954

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By Linda L. Chasko, Ronald S. Conti, John D. Cool

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion, roof fall or water innundation. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted, and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety and several mining companies. The exercises were conducted at NIOSH’s Lake Lynn Laboratory and operating mines during 1995 to 1999 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included various chemical light shapes and laser pointers to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escapeways and marking crosscuts, and thermal imaging systems to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. Anew team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 400-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” administered first aid, mapped the passageways, built temporary stoppings, and ventilated the smoke-filled entries. Advanced training included the extinguishment of a conveyor belt fire in a surface fire gallery. Two teams, each carrying charged waterlines, were escorted into the fire gallery through both doors. These teams controlled the rollback smoke and extinguished 7 to 9-m of burning conveyor belt. Team members indicated that the exercises were extremely beneficial due to the realism of thetraining simulations.

By P. D. Bergman

To assess the efficacy and economics of producing power from coal, four open-cycle magnetohydrodynamic (MHD) processing schemes were selected for study. Each involved a different mode of coal combustion and level of gas cleanliness. The options considered were: (1) coal burned in a slagging combustor; (2) suspension gasification with slag removal prior to combustion; (3) parallel cyclone combustors, one operating fuel rich and the other operating with excess air; and (4) suspension gasification by the hot exhaust gases from the MHO duct with ash removed prior to combustion. Option 1 has the highest ash content in the combustion plasma and as a result would have the greatest operational difficulties associated with it. Options 2 and 4 have the cleanest MHD combustion plasma. For coal priced at $4/ton, the power generating cost of option 4,11.78 mills/Kw-hr, is the highest, with Option 1, at 9.04 mills/kW-hr the lowest. These costs may be compared with a conventional power cost of 9.92 mills/kW-hr for the late seventies. Capital costs of three of the four options were competitive with those of conventional thermal power plants employing stack gas S02 cleanup systems. Option 2 has the most favorable combination of operating characteristics and power cost. It was concluded that a clean, high-temperature working fluid can probably be produced from coal without leading to depressed system efficiencies and exorbitant capital costs.

Jan 1, 1973

By R. R. Sayers

"An important, function of the U.S. Bureau of Mines is to instruct miners in first aid, and as a means of promoting interest in it first-aid contests are held under the auspices of the Bureau, usually in coop; ration with other interested organizations, especially the American Red Cross, the National Safety Council and various operators' and Miners' associations. It was early found that the method of judging first-aid meets is one of the most vital factors in determining the degree of success of the meet.It may be safely stated that there is no method for the judging of first-aid contests that has proved ideal. A method that would give the most uniform judging would necessitate the rating of each team by the same judge or committee of judges and, in order that a judge may rate a team satisfactorily, he should see that team perform several events and average the ratings. Such a procedure is not practicable where there are many terms entered in the contest, as it would prolong the meet indefinitely. To overcome this objection the method has been tried of assigning separate judges to each team but this brings in a new factor the individuality of the various judges, some of whom rate closely, others loosely. The next development was to average the judging by having the judges rate different teams for each event. This would seem to solve the problem out it has been found, after using the method over a wide area for a considerable period of time, that the differences in the judging are too marked to be at all satisfactory. The next development was to appoint a committee of chief judges three to five in number especially trained and experienced, to aid the individual judges in rating the teams. This method has proved satisfactory at small meets but, as committee must review the work of each judge on each event, it has not been deemed feasible for a large meet."

Nov 1, 1920

By L. B. Pankratzt

The heat content above 298.15° K of ferroelectric lithium columbate (LiCbO3) was measured to 1,770° K. The Curie temperature was determined to be 1,450° K, the melting point 1,540° K, and the heat of fusion 16.94 kcal/mole. Heat content and entropy increments have been tabulated for the temperature range from i98.15° to 1,800° K. Heat contents are also given in equation form.

Jan 1, 1966

By B. M. Bench

This Bureau of Mines report describes photo lineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W -N 15° E, and N 57° W -N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W -N 20° E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W -N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977

By Jean M. Kenney

Frequencies of haulage-related accidents in metal and nonmetal surface mines for the years 1988 through 1990 were investigated and compared with those of non-haulage-related accidents. This study was part of the U.S. Bureau of Mines program to improve mining haulage safety. Data were obtained through the U.S. Bureau of Mines Accident Data Analysis (ADA) program. The chi-square test was used to compare frequencies of haulage-related and non-haulage-related accidents for each of the following variables: degree of injury, age, total number of years of mining experience, and shift time. Significance was determined for degree of injury between haulage-related and non-haulage-related accidents. Age of injured did not vary significantly between haulage-related and non-haulage-related accidents, but total number of years of mining experience was found to be significant. Shift time for the accident proved to vary significantly between haulage-and non-haulage-related accidents. Events causing injury for haulage-related accidents were tabulated, and the most frequent determinants of haulage-related accidents were identified. Accident descriptions for both fatalities and permanent disabilities were studied, and the primary causes of these accidents were identified. These findings suggest that haulage-related jobs are among the most dangerous when considering accidents experienced by all workers in the metal and nonmetal surface mining work force.

Jan 1, 1993

By Samuel P. Harteis

Many mining operations rely on retention bulkheads to provide a barrier between impounded water and active mine workings. However, bulkhead failures can cause catastrophic flooding that puts the underground workforce at risk. Underground observations and evaluations of existing bulkheads indicate that a systems approach is required when building an underground water or slurry retention system. In addition to engineering the bulkhead, the designer must ensure the quality control of materials and workmanship of the bulkhead, the reaction of the mine strata when exposed to water under pressure, and methods to monitor the performance of the retention system. Researchers from the National Institute for Occupational Safety and Health (NIOSH), with the assistance of the Mine Safety and Health Administration (MSHA), conducted an extensive review of bulkhead permits submitted to the MSHA Technical Support office in Bruceton, PA. In addition, the researchers visited accessible bulkhead installations at undeground mining operations to gather information related to construction practices, maintenance issues, and monitoring and emergency response procedures. Several key items were identified that must be considered when permitting the installation of an underground fluid retention system.

Jan 1, 2008

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

Provide respiratory protection for escape in a toxic or oxygen-deficient atmosphere with a device small and light enough to be belt-worn. Approach Combine a 10-minute, belt-worn respirator with a stored, larger, long-duration (60-minute) attachment that can be plugged into the 10-minute unit without removing the mouthpiece. How It Works The 10-minute device will be carried by the miner at all times, and the 60-minute canister or attachment will be stored near the miner. In the event of a disaster, the 10-minute device would be donned immediately. The miner would then proceed to the stored 60-minute unit and plug it into the 10-minute unit. For the 10-minute unit, a breathing circuit was developed in which air is passed through the KO2 bed twice per respiration. The 60-minute canister differs from the 10-minute unit in that air is drawn only once through the chemical bed per respira-

Jan 1, 1981

By Ronald T. Mayerle

In 1989, the U.S. Bureau of Mines conducted a mineral investigation of the Mallard study area near Elk City, Idaho. The study area comprises most of the original Mallard RARE II area (1-847) plus some additional lands. The investigation is part of an ongoing, multi-year study of north-central Idaho that is being conducted in cooperation with the Idaho Geological Survey and the U.S. Geological Survey (USGS). The only identified resources are rock suitable for road metal. Five lode prospects and a pyrite-bearing rock quarry, which is operated by the Forest Service for aggregate, were examined for metals. One of the prospects warrants additional exploration for silver in quartz veins, but the chance of finding an economically minable deposit is limited. Several rock and stream sediment samples were anomalous in various metals. Two of the more promising localities for gold and/or other metals are adjacent to a unit of the Frank Church-River of No Return Wilderness that the USGS classified as having a moderate potential for gold deposits related to fossil hot springs.

Jan 1, 1991

Lower the respirable dust exposure of longwall shearer operators with improved water spray systems on the shearer. Approach Orient sprays (rather than relocate them) so that dust is held against the face. How It Works Research by the Bureau has indicated that shearer operator dust levels depend largely on how fast dust from the upwind drum spreads into the walkway. Water sprays on the shearer body can greatly affect the spreading of this dust because each spray moves air like a small fan, generating strong cross-currents of air around the shearer. Poorly designed spray systems, especially those with nozzles pointing upwind, will stir up much more dust than they sup-press. On the other hand, Improved systems may be designed to hold the dust cloud against the face while also suppressing It. In such arrangements the water is sprayed downwind and used with screens made from conveyor belting.

Jan 1, 1981

By Stephen C. Tadolini, Raymond A. Mazzoni

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these “simple” devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors’ opinions of course).

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By R. V. Ramani

This report is volume 10 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Ventilation subsystem of the Master Design Simulator. The Ventilation subsystem has the capabilities to handle: (1) branches in parallel or series, (2) fans in parallel or series, (3) multiple fans, (4) methane, compressed air, or other injections into the system, (5) leakages and fixed quantities, and (6) calculations of absolute pressure at nodes. The program uses the Kirchoff's Junction and mesh laws, and the Hardy-Cross iterative technique to converge to the desired accuracy in solving fox the head quantity. A case study is included in the report illustrating the use of the model. The appendices of the report constitute a user's manual for the Ventilation subsystem, and include a program listing.

Jan 1, 1975

By E. S. Leaver

The mineral value in the ores from the Mother Lode mining districts of California is almost entirely gold, Although many mines have produced extremely high-grade ore the usual mill grade averages approximately $7.00 gold per ton. Fully 80 per cent of the gold has been and is now being recovered by amalgamation. Various methods have been introduced to recover the gold that was not obtained by the amalgamation processes. They include vari¬ous kinds of gravity concentration which in some cases were followed by chlorination or cyanidation. The usual practice includes only stamp battery, plate-amalgamation, and vanner concentration. In the very early practice the tails were run to waste through the main drainage streams of the different mining districts. During later years very large storage dumps have been impounded. These old tails, together with those being saved from present mills, furnish the problem discussed in this article. The clean sand portion of these mill tails is amenable to the usual cyanidation. The slime portion contains the major amount of the gold lost, but it also contains 1-1/2 to 3 per cent carbon, which precludes direct cyanidation of this part of these low-grade waste tails. The black carbonaceous slime portion is the particular problem considered in this report.

Jan 1, 1930

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940