Search Documents

By I. W. ROBERTSON, G. G. Oberfell, G. A. Burrell

The Bureau of Mines, in pursuing investigations looking to greater safety in mining, has analyzed samples of the air in many different coal mines in the United States, and has studied the analyses. This report presents the results of one phase of this study and shows how atmospheric air, after entering a coal mine, loses oxygen and gains carbon dioxide with resulting formation of so-called black damp. Also the report discusses the effects of the constituents of black damp on men, on the burning of oil and acetylene lamps, and on the ex- plosibility of methane. The term "black damp" was and still is widely used to designate accumulations of carbon dioxide, but a more exact definition of black damp, as Haldane, the English physiologist, has pointed out, is an accumulation of carbon dioxide and nitrogen in proportions larger than those found in atmospheric air. The reasons for preferring Hal- dane's definition are given on succeeding pages.

Jan 1, 1916

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By Larry A. Haas

Carbonyl sulfide (COS) was decomposed to sulfur and CO in a silent electrical discharge. A threshold of about 4 kv at 60 Hz was required to dissociate the gas in a laboratory ozonizer at 790 torr with electrode gaps between 1 and 5.5 mm. Above the threshold value, the reaction rate increased with increasing voltage with helium or nitrogen diluent. With the latter diluent, higher voltages had to be applied to obtain the same yield in the 4-to 12-kv range. The COS decomposition rate increased with COS concentration, but a saturation value was reached at about 10 pct COS. The reaction rate decreased at low linear gas velocities as obtained at lower gas flows, larger electrode gaps, or larger reactor volumes. Increasing gas temperature also decreased the decomposition rate. The presence of solid adsorbents such as quartz wool, bauxite, or charcoal had no significant effect on the reaction rate. The addition of S02 did not affect the COS decomposition rate, but small amounts of water decreased the reaction rate. Over 50 pct of the COS was decomposed at room temperature and atmospheric pressure in a l7-kv ozonizer using a gas containing 0.9 pct COS in helium flowing at a rate of 0.3 liter/min. The average current was less than 5 ma. This method has possible application in eliminating the toxic air pollutant, COS, which is generated in petroleum refineries and in processes involving reactions between sulfurous and carbonaceous materials. Carbon monoxide that is formed can be further oxidized to CO2 after the collection of elemental sulfur.

Jan 1, 1972

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

By William H. Pailes, Vincent Castronova, Daniel Lewis, Norman L. Lapp, George Goodman

"INTRODCJCTIONAlveolar macrophages are free lung cells located on the surface of small airways and alveoli. These phagocytes play an important role in the protection of the lung against airborne bacteria and particles.1 However, hyperactivation of pulmonary phagocytes can lead to excessive secretion of enzymes and reactive oxygen species which could result in lung injury, emphysema, or fibrosis.2,3 Analysis of bronchoalveolar lavage effluents for cell types and cellular activity has yielded information concerning the etiology of various pneumoconioses. For example, emphysema associated with inhalation of coal dust or cigarette smoke has been related to enhanced secretion of reactive oxygen species from alveolar macrophages.4-7 In contrast, hypoactivation of alveolar macrophages has been associated with inhalation of diesel particulates"" and has been related to increased susceptibility to pulmonary infection. s Inhalation of cotton dust has been associated with dramatic increases in lavagable polymorphonuclear leukocytes9 while pulmonary sarcoidosis and silicosis have been related with high numbers of lymphocytes in lavage effluentsl0,11The objective of the present study was to obtain lavage effluents from 8 control subjects, 8 healthy power plant workers exposed to fly ash, 1 healthy coal miner, and 1 rock driller with acute silicosis. These effluents were analyzed for total numbers of alveolar macrophages, lymphocytes and neutrophils and for secretory activity of alveolar macrophages. Data were then analyzed to determine what response patterns were characteristic for given dust exposures.METHODSSelection of SubjectsThe 8 control subjectS were all adult males from the area of Morgantown, WV. Two subjects among the controls had smoked cigarettes for approximately three pack-years and had stopped more than ten years ago. The 8 power plant :workers were all healthy adult male employees of a power facility in Hatfield, PA, approximately thirty miles from Morgantown. One of the power plant personnel was a comparable ex-smoker. The remaining subjects were all lifelong non-smokers. The coal miner was a healthy non-smoking male from Morgantown, WV. The rock driller was a patient under treatment with corticosteroids for acute silicosis. He had shown considerable clinical improvement with this treatment but still manifested significant radiologic and pulmonary functional abnonnalities at the time of lavage. The mean age of the 8 control subjects was 36 years (range: 31 to 49 years); the mean age of the remaining subjects studied was 38 years (range: 29 to 53 years)."

Jan 1, 1990

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti', in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By A. L. Johnson

In this Bureau of Mines report, time-resolved infrared emission spectra and corresponding pressure and temperature histories are reported for large-scale propagations of CH4-air, CH4-air-N2, and CH4-air-CF3Br ignitions in a 12-ft-diam sphere. Absolute spectral radiances were obtained throughout combustion over the 1.6- to 4.8-gym range, and the radiance growth patterns for the H20 (2.5-µm) bands are presented as a function of methane stoichiometry and diluent concentration. Flame temperatures were determined from the C02-band emissions, which approximated unit emissivity shortly after ignition. Burning velocities are also given for some of the test-mixture compositions. Measured flame temperatures were in excellent to fair agreement with theoretical adiabatic values for the CH.-air and CH4-air-N2 mixtures; the best agreement was for the stoichiometric CH4-air mixture. The CH4-air-CF3Br mixtures with =2 pct CF3Br gave poor agreement with theory. The measured temperatures were significantly lower during the early stage of combustion; furthermore, the later stage of combustion was uninhibited and yielded unexpectedly high pressures. Supplemental data from a 2-ft-diam sphere at various initial pressures confirmed that the CF3Br inhibition effectiveness decreases with increased pressure. The possible effects of buoyancy, turbulence, and changing kinetics are discussed.

Jan 1, 1977

By Fredrick L. Johnson

In 1984, at the request of the U.S. Forest Service, the U.5, Bureau of Mines began a study of the 94,370-acre Arc Dome study area (4-667) in order to appraise its mineral resources, The Bureau of Mines mapped and sampled mines, prospects, and mineralized sites in and near the area, The study area is located in the Toiyabe National Forest, about 54 mi north of Tonopah, Nye County, NV, It is estimated that over 500 claims have been staked in the study area since the mid-1800?s. In January 1986, there were 108 active mining claims completely inside and 59 on the boundary. Another 283 active claims were outside the study area but within 1 mi of the boundary, In addition to the large number of claims staked, exploration activity is also reflected by the almost 700 inactive workings that were found during field investigation.

Jan 1, 1989

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By Albert E. Long

This paper presents a description of the operational mechanics involved in block-caving a granodiorite-capped, limestone deposit. This method was used for 24 years at the Crestmore mine, near Riverside, Calif., which was operated by the Riverside Cement Co. as a source of raw material used to manufacture a portland cement. The Crestmore mine is the only place where a block-cave method has been used to mine a limestone deposit. Structurally, limestone is relatively strong, and it is not usually considered to be a substance amenable to mining by block caving. It is therefore a credit to the engineering department of the Crestmore mine that it developed a satisfactory, relatively efficient method of block-caving a structurally stable rock. In the discussion, covering the methods applied to produce about 7.9 million tons of limestone and granitic rock materials by block caving, particular emphasis has been placed on an assessment of (1) physical properties of the deposit, (2) ground pressure and support, (3) methods used to induce fragmentation and maintain cave action, (4) surface and subsurface subsidence, (5) secondary blasting of oversize, (6) production rate, (7) safety, and (8) the advantages and disadvantages of the cave method as applied to this specific limestone deposit.

Jan 1, 1958

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By A. Wahab Khair, N. P. Reddy

"Abstract. This paper attempts to characterize coal breakage due to the action of a continuous miner. Coal blocks with an approximate dimension of 45.7 cm x 38.1 cm x 15.2 cm (18 in. x 15 in. x 6 in.) were first subjected to confining pressures equivalent to in-situ conditions. Then the blocks were cut along the face/butt cleat direction by the cutting head of a specially designed unique automated rotary coal cutting simulator (ARCCS), simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-sit and operating parameters a number of other para¬meters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis.INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969 was enacted to emphasize to coal operators that the airborne respirable dust should not exceed 2 mg/m3, thus reducing the incidence of coal workers pneumoconiosis.Dust control techniques such as conventional water sprays and dust collectors are only partially effective and require additional equipment expenditures. A more authentic approach would be to reduce respirable dust at the source the continuous mining machine cutting head, where the fragmentation process occurs. Improving the fragmentation process by characterizing the coal breakage will not only reduce respirable dust at the face, but it will also decrease the amount of respirable dust that is liberated during the secondary handling.Fragmentation of coal can be expressed as a function of three major groups of parameters; namely, 1) coal properties, 2) in-situ conditions and 3) operating parameters. This paper deals with the characterization of coal breakage along both face/butt cleat direction as a function of machine operating parameters such as rate of advance, angle of attack, bit configuration, bit lacing (spacing and pattern) and bit speed at various equivalent in-situ pressures."

Mar 1, 1989

By M. J. Ackerman, C. R. Waine, W. M. Merritts, L. P. Mokwa

Tests were conducted in the Pocahontas No. 4 coalbed in southern West Virginia to determine if successful degasification techniques, developed during an earlier study in the Pittsburgh coalbed, would be effective in removing methane from those usually more gaseous coals. Specially designed long-hole drilling equipment and Bureau of Mines continuous recording devices were used to measure the quantity and methane content of the ventilating air during the investigation. Infusions were made with water at normal waterline pressures ranging from 200 to 220 psi or at pump pressures ranging from 400 to 650 psi. Results of the tests showed that methane emissions from free-flow bleeder holes were as much as 131 cfm. Infusions of some of the holes increased the methane emission from other holes and from the exposed coal surfaces near the working areas as much as 1,540 cfm. The methane content in the main return-air currents after infusion was reduced more than 86 percent of the amount recorded before tests were made.

Jan 1, 1963

By Young W. A.

The Eagle Silver mine is in the Rush Valley mining district, Tooele County, Utah, and is now operated by the Hampton Mining Co. The property, originally referred to as the Argent, is reported to have been one of the first discoveries in the district. The early operators mined ore to a depth of 850 feet, at which point the property was abandoned because of excessive water. During 1905 the Honerine tunnel was driven into the area approximately 1,800 feet below the collar of the Argent shaft. This tunnel served to drain the levels above and operations were resumed. Ore deposits in the Eagle Silver mine occur in the Galena King lime-stone, a 20-to 60-foot member of interbedded quartzite and limestone in the Oquirrh formation of Pennsylvanian age. This member has been faulted along the bedding, forming the Galena King gouge. Mineralization commonly occurs in or near this gouge area in a brecciated, highly altered, pipelike zone. The known ore shoots occur in association with the breccia pipe, commonly adjacent to cross faulting and porphyry intrusions. In general, two ore shoots have been mined on the upper levels of the mine, one lying to the east and the other to the west of the breccia zone. The Bureau of Mines diamond-drilling program was begun during the latter part of 1948 and completed early in 1949. Nine holes were drilled, aggregating 852.8 feet. Sludge and core samples from mineralized sections were analyzed in the Salt Lake City laboratories. A total of 87 sludge, 71 core, and 11 chip samples was submitted for analysis.

Jan 1, 1950

By Jack C. White

As part of an investigation of the production of alumina by the nitric acid leaching of kaolinitic clay, the Bureau of Mines designed, built, and tested a fluidized-bed system for the calcination of aluminum nitrate nonahydrate to alumina, while recovering nitric acid. The calciner consisted of an 8-in-square by 36-in-tall vessel containing 18 in of fluidized solids. Molten aluminum nitrate, sprayed directly into the fluidized solids, formed sandy, granular alumina by growth of successive layers on fluidized particles. Solids were fluidized in a dense bed at temperatures of 250° to 500° C with steam, air, or mixtures thereof. Decomposition of nitrate ranged from 4 to 10 pet during single-pass steam or air fluidization, respectively. Alumina dust losses and low throughput are significant unsolved problem areas.

Jan 1, 1982

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989