Search Documents

By Stephen R. Wilson

This paper is one of a series published by the Bureau of Mines on the mineral resources of the Nation. It describes briefly the occurrence of sodium sulfate in Salt Lake and Tooele Counties, Utah, presents data on sampling, and describes ex-traction and refining raw material and a mining research project that has been conducted on the deposits. ACKNOWLEDGEMENTS Acknowledgments are given to the Tintic Standard Mining Co., Salt Lake City, Utah, and Bartlett Chemicals, Inc., New Orleans, La., for permission to use data obtained by the companies. The authors also acknowledge the courtesy of J. A. Marsh and H. K. Thurber, geologists and mining engineers, for permission to use information in reports prepared by them.

Jan 1, 1957

By John J. Sammarco

The U.S. Bureau of Labor Statistics reports that the mining industry has the highest average annual fatality rate (31.9 per 100,000 workers) among all major American industry. To address this, a major research program to reduce hazard exposure of miners with computer-assisted mining equipment was initiated by the U.S. Bureau of Mines.1 One application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the haulage equipment so that it follows the machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors that can survive the hostile mine environment of dust, methane gas, and water, play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations were conducted to establish operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a sensing system. Various technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications but were found unacceptable. However, a near infrared (IR) sensor employing active targets met the requirements. The sensor has a nominal 75° conical field-of-view and a range from 0.1 to 18.0 m. For the single target mode, nominal range accuracy was 4.3% at a distance of 3.56 m. Correction algorithms were generated reducing the error to 0.6%. Airborne dust testing showed less than 0.8% accuracy (worst case) degradation at levels exceeding (by a factor of 7.5) concentrations permitted by Federal law. The sensor can track multiple active targets providing five degrees-of-freedom (DOF) measurements. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. A guidance system for the haulage system to follow the mining machine does not exist commer¬cially. Such a system can reduce fatalities and injuries by current haulage mining equipment, and is a viable alternative to current haulage control.

By Thomas C. Denton

The fluorite, deposit discussed herein occurs on a property known as the Snowball and comprises five contiguous mining claims in Maricopa County, Ariz. Attention of the Bureau was first directed to this property early in 1944 through .a request by D. B. Powell, original locator; to investigate his property as a possible source of fluorite and one that might 'Warrant exploration by the Bureau. The property was examined by two Bureau engineers, Thomas C. Denton and Geo. W. Huseman. It was decided to investigate the occurrence further by trenching, sampling, and diamond drilling. Work began on May 15, 194. Preparatory work, trenching and surface sampling, was supervised by Geo. W. Huseman. Drilling was in charge of R. M. Grantham. The project was completed August 8, 1944.

Jan 1, 1949

By W. L. Heidenreich

This report describes the methods and results of field investigations conducted by the Bureau of Mines between December 1956 and December 1957 on seven deposits of nickel-cobalt-iron-bearing laterite and weathered serpentine near the west coast of Puerto Rico east and south of Mayaguez. These deposits were named, for purposes of identification, Guanajibo, Punta Guanajibo, Las Mesas, north and south deposits of the Rosario Southeast group, and the west and east deposits of the Maricao Southwest group. In addition, the lower 17 miles of the Guanajibo River Valley was tested at widely spaced intervals for possible concentrations of magnetite and chromite in the alluvial sands. The objective of the investigations was to appraise, by drilling and sampling, the two largest deposits--the Guanajibo and Las Mesas. Testing of the smaller deposits was much more restricted. Field investigations consisted of mapping, drilling with power auger, sampling drill-hole sections, and pre-paring samples for chemical analyses, mineralogical studies, and metallurgical tests. The work was financed jointly under a cooperative agreement by the Bureau of Mines and the Economic Development Administration, an agency of the Puerto Rican Commonwealth.

Jan 1, 1959

By S. F. Ravitz, T. M. Romslo

During 1940 and 1941, the Bureau of Mines examined a large number of silver mines in Arizona for their potential as producers of manganese ores. Although very little manganese ore had been produced from these mines, it was generally known that manganese oxides in appreciable amounts were associated with the silver ore. Following the examinations, the Bureau further investigated some of the ore deposits by diamond drilling and other types of sampling. The results of these investigations, from the viewpoint of manganese, were discouraging. However, the investigations did indicate that appreciable tonnages of manganese-silver ores had been left in some of the mines by earlier operators. Most of these ores were too low-grade for direct shipping as ores of manganese or silver, and their beneficiation by ordinary processes was not economic. Exploitation of the ores appeared to be dependent upon the development of a low-cost milling method, which would yield a marketable manganese product and recover a high percentage of the silver. Later, the Bureau of Mines constructed an experimental mill at Salt Lake City, Utah, for the treatment of manganiferous ores by the dithionate process, designed to recover manganese as a high-grade product. The dithionate residues can be treated by other processes for the recovery of additional values that may be present in the ore. This development focused attention on the manganese-silver ores of Arizona and led to setting up Bureau project No. 370, which is the subject of this report.

Jun 1, 1947

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By Charles E. Whieldon

The importance of recovering more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. A previously published report4/ described the highly successful results of waterflooding in the Weir sand in eastern Kentucky. A more recent report5/ evaluated the results of waterflooding in Roane County, W. Va. (See fig. 1.) Two waterflooding projects have been operated in Pleasants County, W. Va. (fig. 2), one by the Dearborn Oil & Gas Corp. in the Cow Run sand near Calcutta, McKim and Washington districts, and the other by George C. Schoonmaker in the Maxton sand at Bens Run, Union district. This report report describes the waterflood operation near Calcutta, W. Va.

Jan 1, 1960

By GEORGE S. POPE

The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form but the same in principle, has been gradually adopted by other departments until at present of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publications listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples represent- ing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the speci- fication method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly repre- sentative of the commercial product delivered in wagons, railroad

Jan 1, 1913

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By G. E. McElroy

[During the period July, 1923, to April, 1924, we made a large number of careful determinations of the resistance to the passage of air in selected sections of airways in the metal mines of Butte, Mont. The experiments were conducted with the cooperation of the Anaconda Copper Mining Co., Frank D. Cannon, mining engineer of that company, and Fred P. Gaethke, mining engineer of the bureau, assisted in carrying out this work. This paper summarizes the, main group of data obtained in the form of a table, of friction factors, or coefficients of friction that is, values of K in the generally accented formula or air flow of [P = KSV or H = KSV2 ] where, in units customary to mining practice;]

Jan 1, 1925

By T. A. Henrie

A technique was devised for measuring the rate of chemical reactions between reactive metals and molten-salt mixtures at high temperatures. The rate of the heterogeneous reaction between high-purity titanium metal and titanium trichloride in molten sodium chloride was determined. The reaction is surface-controlled, and the heat of activation is 8.29 kilocalories per mole TiC13. An active site or reaction nuclei is created by adsorbing a TiC13 molecule at the metal surface. Reaction of the second TiC13 species forms an activated complex that decomposes into three TiC12 molecules.

Jan 1, 1963

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

By H. H. Schrenk, F. E. Griffith

"The increase in tunneling operations that requires working under pressures greater than that of ordinary atmosphere has raised the question of the use and possible limitations of respiratory protective devices under such unusual conditions. As little, if any, information is available, there is need for a comprehensive study of this subject before specific recommendations can be made. In the absence of such data it seems desirable to make a few preliminary observations regarding the problems associated with wearing respiratory protective devices under increased air pressures.Two distinct problems must be considered--the mechanics of the apparatus used under such conditions and the physiological effects of increased pressures on wearers of respiratory apparatus. This report is confined to the use of oxygen breathing-apparatus and gas masks under pressure.ACKNOWLEDGMENTSThe data presented were obtained at the Queens Midtown Tunnel under construction at the east end of 42d Street, New York City, during a study of compressed-air illness conducted by the Bureau of Mines in cooperation with the United States Public Health. Service and the New York City Tunnel Authority.Grateful acknowledgment for cooperation and the use of facilities is made to Dr. R. R. Sayers and his associates, particularly Dr. J. W. Crosson (who acted as observer during the oxygen breathing apparatus tests), of the Division of Industrial Hyiene, National Institute of Health; to the Port of New York Authority, through Dr. Edward Levy; end to the contractors, through Doctor Emery."

Jan 1, 1940

In July 1982 the Committee on Underground Coal Mine Safety completed its study of safety in U.S. underground coal mines; the results of the study were published in the National Research Council report entitled Toward Safer Underground Coal Mines. One of the findings of this study was: THERE IS A STRONG CORRELATION BETWEEN MINE SIZE AND FATAL INJURIES. THE FATALITY RATE IN MINES WITH 50 OR FEWER EMPLOYEES IS NEARLY THREE TIMES THAT OF LARGE MINES (WITH OVER 250 EMPLOYEES), AND ABOUT TWICE THAT OF INTERMEDIATE-SIZED MINES (WITH 51-250 EMPLOYEES). Although the Committee explored possible reasons for the higher fatality rate in the smaller mines, it was not able to explain this phenomenon fully. Therefore the Bureau of mines requested that the Committee undertake a supplementary study of fatalities in small underground coal mines. The Committee met in the fall of 1982, discussed the problem, developed an approach to it, approved a program of statistical analyses, and authorized a panel of four committee members to explore the problem in greater depth. The panel, in turn, reviewed the results of the statistical analyses and met with the president of the National Independent Coal Operators Association and with several owners of small underground coal mines for a detailed discussion of the unique problems of small mines. Panel members examined 66 individual fatality reports prepared by Mine Safety and Health Administration (MSHA) inspectors who investigated fatal accidents that occurred in small underground coal mines in 1979 and 1980. This report is the result of those studies, analyses, and deliberations. The first draft was prepared by the panel, but the report has been reviewed and approved by the entire Committee.

Jan 1, 2011

In This Chapter [Ventilation: dilution and displacement Water sprays: wetting and airborne capture Water additives: foam and wetting agents Dust collectors: filtration efficiency and inlet capture efficiency Reducing the generation of dust for cutting, drilling, blasting, crushing, and conveying] [This chapter will give you a general perspective on what works or doesn’t work. The chapter will also help if your dust control problem doesn’t fit any of the circumstances described in later chapters. ] This chapter describes the three major control methods used to reduce airborne dust in tunnels and underground mines: ventilation, water, and dust collectors. It also describes methods to reduce the generation of dust, so less has to be removed from the mine air. The ventilation methods provide the best use of air in the vicinity of workers and in the vicinity of dust sources. In this sense, the methods described are local ventilation methods. Most of the emphasis is on so-called displacement ventilation because it is the most effective dust control technique available. The section on water sprays outlines the dual role of sprays—wetting and airborne capture—and describes why wetting is more important. It also corrects some of the misconceptions about spray effectiveness and describes circumstances where sprays can actually increase the dust exposure of workers. The section on dust collectors outlines the circumstances under which dust collectors can be expected to function effectively. It also describes some common design and maintenance problems. The final section describes how to reduce the amount of dust that gets into the air in the first place, since once the dust is airborne it is always harder to control.

Jan 6, 2003

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1983 identified no mineral resources in the Beaver Meadows, Blind Horse Creek, Chute Mountain, Deep Creek/Battle Creek, and North Fork of Sun River Wilderness Study Areas (WSA's). A prospect east of the Beaver Meadows WSA has low potential for lead resources. Sand, gravel, and limestone occurrences are numerous in the WSA's; however, similar or better quality materials outside the areas are abundant and more accessible to potential markets. Impure coal and titaniferous-magnetite occurrences are near the WSA's, but are not known to occur within these areas. In 1983, there were 7,025 acres leased for oil and gas within the five WSA's; no current mining claims were in or near any of the WSA's. Evidence of mining activity was found at only one prospect in the WSA's. It is inside the Deep Creek/Battle Creek WSA; no resources or resource potential were identified at this prospect.

Jan 1, 1984

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

As the use of deep -rut mining increases, there - expected to be a greater demand for methane (CH,) measurement devices capable of scanning working faces al depths in excess of 10 m to alert mine personnel of hazardous concentrations of CH and to satisfy regulatory requirements. Remote optical devices offer the most promise to satisfy these objectives while the operator remains safely under supported roof. A second¬-generation remote Optical methanomeor (ROM) bas been designed and Is undergoing laboratory evaluation at the National Institute for Occupational Safety and Health. It operates on the principle of differential absorption of the "u;' fundamental absorption band of CH, centered at 3.31 um in the infrared region of the spectrum. The new instrument differs from the previous prototypes by the replacement of the two hand pass differential absorption technique of measurement with a single filter gas correlation technique and a refinement of the amplifier and gating circuitry used within the unit. This results in a more accurate isolation of the CH, spectral absorption band centered at 3.31 um. A specially designed 0.4m-diam variable-length gas mixing tunnel was constructed and instrumented with CH4 sampling capability to calibrate the ROM. Experiments have demonstrated the ability of the detector to respond to various conditions of CH, (pn•m) at distances as great as 12 m. Thermal radiation generated within the instrument is the controlling factor in the drift of the output signal nod, therefore the reliability of the instrument. Several approaches to reduce this extraneous radiation interfering moth the infrared detector, described, such as the installation of a fan in the instrument and thermoelectric coolers on the detector's beat sink. Implementation of this technology will significantly improve the safely of miners.

Jan 5, 1997

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for two longwall mining operations in the Northern Appalachian Coal Region. Vertical displacements and relative face positions are tabulated for 104 subsidence monuments. Brief physiographic and geological descriptions of the mining sites are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By A. D. Mah

Thermodynamic data on compounds of arsenic and sulfur were critically evaluated by the Bureau of Mines. Changes of standard enthalpy and Gibbs energy, and logarithms of the equilibrium constants were tabulated as a function of temperature for reactions involving these compounds.

Jan 1, 1982