Search Documents

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By J. A. Eisele

The Bureau of Mines is investigating the recovery of alumina from domestic nonbauxitic resources, including anorthosite. The United States has large reserves of anorthosite, but its aluminum content is less than 50 pct soluble in acid, unless a source of fluoride is added to the acid. A flowsheet that includes leaching with HCl and fluoride followed by crystallization of AlC13.6H20 from the pregnant liquor by HCl gas injection was designed. Approximately 90 pct of the aluminum values were recovered from the anorthosite when a ratio of 0.14 mole of fluorine per mole of aluminum was used. Sodium chloride is cocrystallized with the A1C13.6H20 but is removed by water washing of the Al203 product. A material balance is given based on results of laboratory studies of the unit operations.

Jan 1, 1983

By E. Morrice

High-purity lanthanum metal was prepared by electrolysis of La003 in a LaF3-LiF-BaF2 bath at 950° C. The requisite bath temperature for the deposition of molten metal was maintained by supplying the heat as current directly to the electrodes. A current efficiency of about 60 percent was obtained. The lanthanum nodules contained carbon and oxygen as major impurities. The total impurity content was from about 0.1 to 0.2 percent.

Jan 1, 1962

By H. J. Seim

An ion-exchange-instrumental analysis technique is described for analyzing impurities at 1 to 1,000 parts per million level in rare-earth metals. A cation-exchange flame photometric method is used for the alkali and alkaline earth groups of metals, and an anion-exchange procedure is used in conjunction with polarographic and X-ray fluorescence techniques for selected transition elements. The standard deviation is about 6 percent, and the average error, about 5 percent.

Jan 1, 1962

By A. S. Griffiths, J. E. Evans

Noise processing experiments with ELF (3 to 300 Hz) atmospheric noise and signals in the 40 to 80 Hz range are described. The primary purpose of the experiments was to record and analyze wideband ELF noise in order to design the noise processing portion of a receiver which minimizes the required transmitter power. The application of appropriate theory and extensive simulations led to a noise processor which consists of the following functions: (1) a compensating (or whitening) filter, (2) a prenotch filter clipper, (3) notch filters at frequencies of manmade interference (e. g., power lines), (4) a post-notch filter clipper, and (5) a phase-coherent linear matched filter. The nonlinear processing provides considerable gain relative to a linear receiver (i. e. , a receiver consisting only of a matched filter and appropriate whitening filters). It is convenient to measure sys tem performance in terms of an "effective noise level" which is equal to twice the received signal energy divided by the signal to noise ratio at the matched filter output. For example, the highest effective noise levels observed at 45 Hz with the nonlinear processor were about -134, -131 and -137 dB wrt 1 amp/m [Hz] using Saipan, Malta and Norway data, respectively, compared to 1 percent exceedance levels of effective noise for the linear receiver of about -115, 115 and -130 dB wrt 1 amp/m [Hz] respectively.

Jan 1, 1973

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow,VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

By Nicholas T. Zilka

Mineral resource studies by the Bureau of Mines indicate three areas within the Selway Bitterroot Wilderness have mineral resource potential. Regional studies suggest that a granitic stock on the south side of the Wilderness has high potential for a Climax-type stockwork molybdenum deposit (pl. 1, no. 8); but detailed surface investigations failed to recognize a deposit. The Elk Summit area on the north side of the Wilderness contains subeconomic resources of columbium (niobium)-bearing ilmenite in placers (p1. 1, no. 19). Subeconomic silver-copper-lead resources occur in a vein on the northeast side of the Wilderness at the Clift Mine (pl. 1, no. 2-5). The study area has no known deposits of oil and Haas, coal, geothermal resources, or other energy-related commodities.

Jan 1, 1982

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

By M. K. Larson, J. P. Dunford, E. G. Zahl, T. M. Brady

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an on going effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for implementing a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. However, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

By R. C. Corey

Anticipating the need for convenient, economical, and safe means for disposing of combustible wastes contaminated with low-level activity, in connection with private and institutional uses of radioisotopes, the Atomic Energy Commission (AEC) has provided the Bureau of Mines with funds to develop an incinerator for this purpose. A prototype incinerator, designated hereafter as BOMAEC-30, was designed, constructed, and tested, based on fundamental and applied research investigations of the combustion characteristics of rubbish and sawdust, which will comprise the bulk of contaminated wastes. No radioisotopes were used in the tests; the objective was to remove as much particulate matter from the products of combustion as possible. The prototype unit was designed to burn 30 pounds per hour, using 100 percent over fire air admitted tangentially in an all-metal, cylindrical combustion chamber. The gas-cleaning system consisted of special fabric bags and absolute filters.

Jan 1, 1962

By D. Harrington

In general, mining is carried on underground, that is, in confined places where it is difficult to obtain adequate lighting and frequently in rock strata requiring much care to prevent caving. Moreover, explosives must be used in mining with the numerous hazards associated with them, and some mines give off explosive or irrespirable gases; also, ma- chinery must be used, usually under conditions much more hazardous than on the surface. These and many other considerations cause mining to be probably the most hazardous occupation in which large numbers of our fellow countrymen are employed. Prevention of accidents in the mining industry is far more complicated than in surface industrial work, even of the more hazardous types, because the different elements that enter into possible accident occurrence are ascertained more readily above ground and suitable action can be taken against them; moreover, errors in connection with prevention of accidents in surface industrial work usually affect only one or, possibly, a few persons, while in zines one human error may readily cause an explosion or other untoward occurrence resulting in the death of scores or even hundreds of persons. This difficulty in the prevention of accidents in and around mines is well-known, and most countries and States have regulations to guard the safety and, to a much smaller extent, the health of workers in mining and allied industries. In general, the State laws and regu- lations regarding the welfare of mine workers are merely a skeletonized outline of some more or less fundamental minimum requirements and are far too general to do much more than suggest some procedure which may or may not be safe or healthful. Most of them are grotesquely out-of-date as applied to present-day conditions, and none of them is adequate to protect life, limb, health, or property. Unquestionably, there is great need for a closer correlation of the laws and regulations of the various States with regard to safety in the mining and allied industries, and while mining conditions vary far too much for a standardized mine safety law applicable to all of the States, on the other hand there are numerous standard and fairly fundamental safety pro- visions which apply to all mines and which should be embodied in the mining codes of all States. Undoubtedly, these standardized safety requirements would be opposed by a consider- able part of the industry, but the ultimate effect would be beneficial to the owners, work- ers, and the general public. For many years progressive mining companies in the United States have not been satisfied to operate only within the meager safety requirements of the State laws or regulations and have adopted additional and far more effective safety procedure of their own, although com- plying also with the State laws and regulations. As a result of this forward-locking policy, zany of these companies have made astonishing progress in the reduction of accidents.

Dec 1, 1935

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By Donald W. Mitchell

The fire hazard of neoprene, polyvinyl chloride, and rubber conveyor belts was studied at the Federal Bureau of Mines Experimental Coal Mine. The effects of intensity of ignition source, velocity of the ventilating air, and type of belt were investigated at three levels in small-scale gallery experiments. Studies were made in the mine on the effects on ignition and flame propagation of belt-entry dimensions, belt widths, and belt configuration. Methods for extinguishing belt fires were also investigated under simulated mining conditions, and during these trials coal dust and grease were placed on the belt. The research showed that conveyor belts will burn. Neoprene, polyvinyl chloride, and rubber belts, with and without carcass, ignited and propagated flame. The highest rate of flame propagation was obtained on rubber belt. The fire hazard increased with increase in intensity of ignition source and air velocity. Flame propagated only when air was forced through the test zone; propagation was not obtained when forced ventilation was not used, as would exist in a neutral entry in a mine. Automatic water sprays and high-expansion foam effectively arrested flame propagation; direct application of water and bicarbonate dusts was ineffective.

Jan 1, 1967

Predict the spontaneous combustion potential of a coal, using an expert system computer program. Background Approximately 15% of underground coal mint fires in the United States are attributed to spontaneous combustion. These spontaneous combustion fires frequently occur in worked-out or abandoned areas of a coal mine, This makes the control and extinguishment of the fire difficult and often requires large sections of the mine or even the entire mine to be scaled for long periods of time. A prior knowledge of the self-heating potential of the coal can be useful in preventing spontaneous combustion fires through the use of aggressive monitoring and control measures at existing coal mining operations, and in the planning oh new mines. Many factors can affect the spontaneous combustion process in a mine, including the self-heating potential of the coal, ventilation, geologic factors, and mining conditions and practices. Various test methods have been used to evaluate the relative self-healing potential of coals, including crossing point temperature and adiabatic heating methods, and oxygen adsorption techniques. However, these tests arc usually time-consuming and difficult to conduct, limiting their use to laboratories.

Jan 1, 1992

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By J. R. Long

The Federal Bureau of Mines has pioneered the work of preparing ductile titanium on a large scale and has also determined the basic properties of this new and most interesting metal. A number of reports (1, 2, 3: 4, 5) have al-ready been published, and considerable interest has been aroused in a number of industrial and research laboratories. Some of these laboratories have also published results of their work on the pure metal. Although the properties of titanium itself are quite promising, it is apparent that considerable improvement may be expected by alloying titanium with other metals. That is, pure metals in general have shown relatively large improvements in properties when alloyed with other metals and titanium is not considered to be an exception to the rule. Therefore, the emphasis of the investigations now under way in the Federal Bureau of Mines Laboratories has been placed on the study of the alloys of titanium, particularly the titanium-rich alloys. While the main interest is in the properties of such alloys, proper direction and evaluation of the work require at least a rough outline of the phase boundaries of the alloy systems involved.

Jan 1, 1949

By George S. Rice, L. C. IlsLey

"A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details:""The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all appearances, passed down the shaft caus¬ing disruptive discharges at certain points between the guides and the winding rope, rending the latter at two places situated respectively .228 .feet and 278 feet from the surface, The distance between the winding rope and the side of the shaft was 5 feet 4 inches, indicating a spark gap ;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft.""The Compressed Air Magazine, January 1920 issue, which contained the above extract also goes on to state;""In 1915, M, Ferey described in a paper read before the Societe de l'Industrie Minerale phenomena of a similar character to the above. In a pit liable to sudden outbursts of gas, for the sake of safety, shot firing was carried out from the surface. During a storm, in the year 1905, shots went off in two places after the detonators had been connected to the conductors) we read in the Colliery Guardian, London. These shots were situated respectively 1,400 and 1,410 metres from the firing station, Realizing the possible danger from this cause, the precaution was taken to cut the conductors at the bottom of the shaft and to connect there just before firing, Even under these conditions a shot went off spontaneously, -.owing, it is believed, to lightning."""

Feb 1, 1920

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982