Search Documents

By Homer J. Ballinger

The Rex mine is one of several zinc deposits in Ozark and Howell Counties, Mo. It is the second of these deposits investigated by the Bureau of Mines in an effort to demonstrate reserves of sulfide ore underlying the shallow carbonate ores from which the district's major production has come. The initial investigation was made during 1945-46 on the Alice mine, Ozark County, Mo.21 The investigation reported herein was conducted during 1947. The Rex open pit is about 250 feet long, 100 feet wide, and about 25 feet deep (average). Three caved shafts are evident in the bottom of the pit, but the extent of the workings from these shafts is not known. The Bureau of Mines drilled five churn-drill holes in and around the Rex pit to test the grade and the vertical and lateral extent of the deposit. Two of the holes indicate notable zinc mineralization ranging from less than 1 to more than 10 percent metallic zinc, but largely in the oxidized condition.

Jan 1, 1948

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By D. Harrington

The fiscal year which ended June 30, 1932, although one of acute financial de ression was, nevertheless, one of distinct encouragement to those who have long struggled against the much too prevalent occurrence of accidents in coal mines, especially of coal mine fire and explosion dis- asters, both of which are now known to be readily preventable. Table 1 summarizes some important information about explosions in the United States coalies for the fiscal year which ended June 30, 1932, insofar as such information is available to the safety division of the United States Bureau of Mines, the personnel of which are under instruction to get in touch with and report on all mine explosions in their respective districts, including not only those occurrences with loss of life but also those in which for- tunately no lives, are affected. Table 1 gives data on 33 ignitions in 10 States with a total of 87 deaths for the year; the number of ignitions (33) is considerably groater than the number (26) for the previous fiscal year, and is exactly the aver- age number for the past four fiscal years; the mumber killed in the 33 ignitions (57) is materially lower than that (217) for the preceding fiscal year or the average (150) for the past four fiscal years. The States with the greatest number of deaths from explosions in the fiscal year ending June 30, 1932, were Virginia; 54; West Virginia, 11; Pennsylvania, 7 (6 being in anthracite mines); Alabama and Colorado, 4 each; Illinois and Kentucky, 3 each; and Maryland, 1. The greatest number of ignitions listod wes that for West Virginia, 7; then came Pennsylvania with 6 (2 being in anthracite mines); Alabama with 5; Colorado, Illinois, Tennessee and Virginia, 3 each; and California, Kentucky, and Maryland, 1 each. The 1931-32 record as given in Table 1 includes several States which were not listed in the previous year: Colorado, Kentucky, Maryland, Tennessee,

Jan 1, 1933

By J. W. Town

The Bureau of Mines conducted petrographic classification and flotation studies to determine if acid-grade concentrates could be obtained from individual and composite samples from the Meade Peak member of the Phosphoria Formation, Idaho. The petrographic studies were made to determine the effect of compositional features on concentration of phosphates. The ore grade, ovule size, and clay content were the main features affecting grade and recovery of phosphate. Flotation results on roasted ore with a tall oil emulsion scheme showed that beds containing over 10 percent P2O5 could be beneficiated and composited with the two high-grade beds to produce a composite concentrate containing 31.9 percent 05 at 84.3 percent recovery. Treatment of these intermediate-grade phosphate beds by flotation increased ore reserves over 200 percent and increased the ore-to-waste ratio in the ore zone from 1:5.7 to 1:0.27.

Jan 1, 1966

By Eliot J. White

The Bureau of Mines tested cores from 35 wells from 14 oil-producing zones in southern Illinois, southern Indiana, and western Kentucky to determine why rates of water injection were apparently low in some zones. Since these zones contain only minor amounts of clay minerals, it is concluded that permeability reduction results from movement of dislodged silica particles and other material, including the clays, that lines the pores. Both single-phase and two-phase permeability measurements, however, indicated that most samples had only low to moderate water sensitivity, so that permeability reduction due to such particle movement should usually not be of practical significance. The effective permeability to water was considerably lower than the effective permeability to oil during two-phase flow measurements, as is typical of most reservoir rocks. It can be concluded, therefore, that relatively high injection pressures will be required in waterflooding thin zones or zones having low permeabilities.

Jan 1, 1966

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It bas already been established that reducing time delays is the most important factor in saving lives. Consequently every event during afire is measured in terms d its duration, and the effectiveness d any action taken to improve survival is measured in terms d the time it saves. By ranking actions according to time saved these authors found that a comhination d actions was most effective. This combination was: • installing lifelines. • moderately decreasing air leakage and • decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study bad shown that, with the exception d delays, single factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

By James D. Noll, Jon A. Hummer, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health conducted a study to determine the effects of selected, state-of-the-art emission control technologies on the ambient concentrations of particulate matter and gases emitted by underground diesel-powered mining equipment. Tests were conducted in an isolated zone of an underground mine to evaluate the effectiveness of alternative fuel formulations, namely, water-fuel emulsions, blended biodiesel fuels, ultralow sulfur diesel fuel, and #1 diesel; and selected exhaust after treatment devices, namely, diesel oxidation catalysts (DOCs), diesel particulate filter (DPF) systems, and filtration systems designed around high-temperature disposable filter elements. The results showed that using a cold-weather and warm-weather water-fuel emulsion formulation reduced mass concentrations of elemental carbon (EC) by about 70% and 85%, respectively. The 20% and 50% soy biodiesel blends reduced EC by 49% and 66%, respectively. The reductions were slightly less pronounced for the 20% and 50% yellow grease biodiesel blends—33% and 56%, respectively. EC concentrations were unaffected by using ultralow sulfur diesel in place of #1 diesel. Use of the reformulated fuels did not substantially alter the concentrations of nitric oxide and carbon monoxide. However, a measurable increase in the nitrogen dioxide (NO2) peak concentration was observed during the biodiesel tests. The ArvinMeritor (AM) fuel-burner DPF system with a palladium-catalyzed DOC reduced EC concentrations by 92%. The diesel filter elements from Donaldson Co., Inc., and Filter Service & Testing Corp. reduced the EC concentration of the mine air by 92% and 70%, respectively. When the palladium-based DOC was used with the AM DPF, it raised the average and peak downstream NO2 concentrations by a factor of three. Tests of the AM DPF system with a platinum-catalyzed DOC and CAP/ETG catalytic particulate oxidizer system had to be terminated because the elevated NO2 concentrations threatened to overexpose the operator. The tests with only a selected DOC also resulted in increased NO2 concentrations in mine air.

Jan 8, 2006

By John L. Reuss

A laboratory study was conducted by the Bureau of Mines to investigate the technical feasibility of decomposing hydrous magnesium chlorides by using a steam pyrohydrolysis technique. This procedure consisted of injecting steam into the atmosphere of a decomposition furnace containing samples of hydrous magnesium chloride and determining the rate of hydrolysis by measuring the rate of chloride evolution. The variables investigated were temperature, amount of water vapor in the decomposition atmosphere, and hydration stage of magnesium chloride. The application of steam was shown to accelerate both the rate and completeness of magnesium chloride decomposition reactions. For example, when magnesium chloride hexahydrate is exposed to a furnace temperature of 600' C in an air atmosphere for 20 minutes, the decomposition is 37 percent. Under identical conditions in a steam atmosphere, the decomposition is in excess of 70 percent. The magnesium oxide produced by the steam pyrohydrolysis of magnesium chloride dihydrate at 800° C contained 98 percent magnesium oxide. Based on magnesium oxide composition, this is equivalent to that of burned magnesite produced at temperatures in excess of 1,300° C. To demonstrate the quality of the product on a practical basis, metal reduction tests have shown it to be equivalent to reagent-grade magnesium oxide as a carbothermic reduction feed material.

Jan 1, 1974

By E. J. Kloos

This publication lists devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, as of May 24, 1972, under provisions of Section 11.2, Part 11, Subchapter B of Chapter 1, Title 30, Code of Federal Regulations (37 F.R. 6244, March 25, 1972), for use in mines as respiratory protection in oxygen-deficient atmospheres, and in gases, vapors, dusts, fumes, and mists. Included are self-contained breathing apparatus, gas masks, and supplied-air, dust, fume, mist, and chemical-cartridge respirators. Names and addresses of manufacturers appear in the appendix.

Jan 1, 1972

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Among the hazards that may attend the use of Diesel engines in mines, tunnels, or other underground operations the presence of harmful or objectionable constituents in the exhaust gas must receive due consideration to prevent the formation of unsafe or unhealthful working environments in these places. Previous reports of this series have presented discussions of the composition of exhaust gas from engines in proper mechanical condition, 6/ the effect of adding some of the exhaust gas to the intake air of the engine, 7/ the effect of operation in atmospheres containing natural gas, 8/ and the effect on exhaust-gas composition of conditions that influence the characteristics of fuel injection in Diesel engines. In all these studies the properties of the fuels used were in general conformity with specifications usually recommended by the manufacturers of Diesel engines. In evaluating the physiological significance of the various components of the exhaust in these experiments, the toxic or objectionable gases determined were carbon monoxide, carbon dioxide, oxides of nitrogen, and aldehydes. Because of the low sulfur content of' these fuels, compounds such as sulfur dioxide and sulfur trioxide were not determined, although in discussion of the test results attention was directed to the fact that if fuels of higher sulfur content were used, the concentration of such compounds in the exhaust would become a significant factor in establishing the quantity of ventilating air required to furnish satisfactory dilut1on of the exhaust gas in underground working places."

Jun 1, 1943

By J. R. Ross

The extraction and recovery of nitrate from waste solutions generated in the production of titanium were investigated using solvent extraction techniques. Laboratory studies and continuous tests in a small solvent-extraction system showed that up to 98 percent of the nitrate can be selectively extracted by a solution of tributyl phosphate in kerosine. The extracted nitrate can be recovered as nitric acid, at concentrations suitable for reuse, by stripping the loaded organic with water.

Jan 1, 1973

By J. R. Ruark

This report presents results of the research and development work and operations performed during stage II of the gas combustion retorting research program conducted by the Colorado School of Mines Research Foundation and six major oil companies at the Bureau of Mines Anvil Points Research Facilities. The experimental program, including retort modification and air-gas distributor development, effects of shale quality and particle-size distribution, and other variables on the process, is discussed. Although operating problems are not fully resolved, it appears that the gas combustion retorting process can be successfully applied to achieve oil yields in excess of 85 percent of Fischer assay at mass shale feed rates of 500 pounds per hour per square foot of cross-sectional bed area, approximately twice the rate previously demonstrated to be reasonably practicable.

Jan 1, 1971

Synthetic dawsonite [NaAl(OH)2C03] has been prepared with crystallinity similar to that of dawsonite found in oil shale deposits of the Piceance Creek area of Colorado. Optimum experimental conditions were as follows: Na/Al atomic ratio, 43; temperature, 175° to 200° C; pCO2, 15 psig; and reaction time 5 hr. Chemical and spectrographic analysis revealed that the synthetic dawsonite was of high purity and Has essentially stoichwmetric. Similarity of the synthetic to natural dawsonite, demonstrated by X-ray diffraction, infrared spectrophotometry, and electron microscopy, suggests its suitability as a standard.

Jan 1, 1972

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981

By A. L. Engel

This report is a compilation of preliminary and, in some cases, more extensive concentration experiments by the Federal Bureau of Mines on low-and medium-grade fluorspar ores from three localities in Nevada and one in California. The work was done on samples obtained from Shoshone mine, Nye County, Valery mine, Pershing County, and the Broken Hills mine, Mineral County, all in Nevada, and Dirty Weather mine, Inyo County, Calif. These investigations were made to aid in the development of domestic fluorspar resources, in line with the Bureau's long-established program of conservation of mineral resources. The treatment methods employed in the experimental work described included simulated or "heavy-liquid" gravity concentration of coarse minerals and comparatively fine-grained minerals, and flotation concentration of finely-ground minerals. These methods were attempted in order to beneficiate the ores and produce concentrates which could be marketed readily, with as high a recovery rate as possible, while using simple treatment methods suitable for small-scale operation.

Jan 1, 1961

By E. K. Kleespies

The rate of the heterogeneous reaction between titanium-oxygen solid solutions and titanium trichloride in molten sodium chloride was determined at high temperatures. In the alpha phase, the reaction rate decreases uniformly with the increasing concentration of oxygen. The gamma crystalline form of titanium (above 33 atomic percent oxygen) was much less reactive than the alpha phase, and the reaction rate approached zero at 50 atomic percent oxygen. The activation energy for the reaction of titanium-oxygen solution containing 22.8 percent oxygen was 11.7 kcal/mole of TiCl3 as compared with 8.3 kcal/mole of TiCl3 for pure titanium.

Jan 1, 1967

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By Herbert M. Wilson

The act (36 Stat., 369) that established the Bureau of Mines in the Department of the Interior defined as part of the bureau's province and duty the making of "diligent investigation of the methods of mining, especially in relation to safety of miners and the appliances best adapted to prevent accidents," and it authorized the bureau from time to time to make such public reports of its work and investiga- tions as the Secretary of the Department of the Interior may direct, with the recommendations of the bureau. The national mine-rescue and first-aid conference was projected in the hope that it would be a factor in increasing safety in the mining industry through the recommendation of better and safer methods of conducting mine-rescue operations, more efficient methods of extend- ing and giving training in the use of artificial-breathing apparatus, and approved and more effective methods of administering first aid to injured miners and of training miners in first-aid work. The bureau feels warranted in publishing the resolutions adopted by the conference as a guide to mine workers and others concerned in obtaining greater safety in mining, and in presenting such extracts from the discussion as indicate the reason for the adoption of any particular method. In issuing this bulletin, however, the bureau does not indorse these resolutions in whole or in part as a final ex- pression of its views regarding the best method or procedure in any case. It does believe, however, that the resolutions furnish an excel- lent starting point from which to develop a standard code of pro- cedure in mine-rescue and first-aid work. It will be noted that in some important cases further information is necessary before any standard procedure can be recommended, par- ticularly as regards types of bandages, methods of resuscitation, the use of stimulants, the cumulative effect of poisonous gases, the diet of men engaged in rescue work, the physiologic effect of the pressure

Jan 1, 1913