Search Documents

Provide a means of evaluating the in place structural properties of coal seams and coal measure rocks in advance of mining. Approach Develop a sonic logging probe for use in dry wells, a condition common to shallow wells and semi-arid coal regions. How It Works The Bureaus' sonic probe differs from conventional sonic probes because it does not require fluid in the well to couple sonic vibrations to the drill hole wall. A self-contained hydraulic system forces pistons containing the measurement transducers against the wall and clamps them in position until the sonic waveform information has been recorded. The pistons are then retracted and the probe is raised or lowered in the well as required. In the clamped position, the piezoceramic transmitter emits a sonic pulse which travels along the drill hole wall and is detected at the receivers in the form of compressional (P) and shear (S) wave motion. The receivers are designed to be sensitive to either the (P) wave or (S) wave motion as determined by the operator so that discrimination between the two wave types is improved by comparison of the respective output channels, and the travel time between transmitter and detectors can be accurately determined. Use of two receiver stations eliminates errors in timing of pulse travel because of electronic delays inherent in the probe.

Jan 1, 1981

By Linneas Laage, Thomas Weber, William Pomroy

"Underground mine fires can significantly influence mine ventilation airstreams, in some cases throttling or even reversing airflows. As a result, the performance of a metal and nonmetal mine stench fire warning system, which depends on the ventilation to carry the vital warning signal, under fire conditions is different from performance under nonfire conditions. The safety of underground miners can be jeopardized if the warning signal is delayed. This Bureau of Mines report describes research to investigate fire and stench warning system interactions. A computer model is presented that permits quantitative analysis of stench warning signal delays as a function of fire location and intensity. The results of a case study involving computer simulations of stench distribution in a hypothetical mine network subject to various fire exposures are also discussed. This case study illustrates a technique for identifying the areas within a mine that are subject to unacceptable warning signal delays, thereby enabling preemptive action by mine personnel, such as redeployment of stench injectors. INTRODUCTIONFires are an ever-present threat to the safety of underground miners. Since the smoke and toxic gas produced by a mine fire can be spread rapidly by the mine's ventilation system, mine evacuation must be accomplished as quickly as possible in the event of fire. In metal and nonmetal mines, the most common means of passing the fire warning signal to each miner is the stench system. The typical stench system utilizes ethyl mercaptan, a highly odoriferous organic compound, injected on the surface into the compressed and/or ventilation airstreams. Upon smelling the stench, workers evacuate the mine according to an emergency preplan.Although the stench system has been used successfully for over 60 yr, it has several serious shortcomings, owing to certain chemical properties of ethyl mercaptan and to certain performance characteristics and limitations of present injection systems.Recent Bureau research succeeded in upgrading the overall safety and effectiveness of the stench system through the use of a superior stench odorant and the development of improved stench injection equipment (1).4 This research has also investigated a specialized computer simulation model capable of calculating the precise concentration of stench in any mine ventilation network branch at any time after stench release (2). An adaptation of the computer model now enables the analysis of stench system and ventilation system interactions under the influence of a mine fire."

Jan 1, 1987

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962

By D. N. Nilsen

A mathematical modeling method was developed by the Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of copper. The use of models for predicting the amount of metal extracted can reduce the amount of experimental work required to characterize a system for purposes such as optimization studies. Models were developed for the extraction of copper from ammoniacal sulfate and carbonate solutions with commercially available extract ants commonly used by industry. Results from laboratory shakeout tests compared well with predictions of the equilibrium concentrations of copper and pH values. For example, the loading of copper onto the solvent was predicted for most cases within ±S pct of the measured values, and the pH to with-in ±O.l pH unit in sulfate systems and ±O.2 pH unit in carbonate systems. Both mechanistic and empirical extraction equations were developed from laboratory data for copper and ammonia. The empirical-based models were slightly more accurate than were the mechanistic-based mod-els. Industrial level concentrations of the aqueous and organic constituents were used in this work. Independent variables included copper concentration, ionic strength, and initial pH of the aqueous phase; extractants, diluents, and their concentration in the organic phase; and temperature.

Jan 1, 1988

By T. M. Barczak, S. C. Tadolini

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of “topping off” the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

By Patricia R. Devine

This report expands an earlier study by Jack Faucett Associates (OFR #40-88) of the same title. Both reports are based upon an interindustry analysis from 1963 through 1982, during which time U.S. metals consumption and production did not keep pace with economic growth. The report discusses three sources of change: technological change, economic growth, and composition of final demand, as well as the relative importance of the individual components of final demand for metals. The results show investment and personal consumption to be the most metal-intensive components of final demand, and technological change to be the major cause of decline in consumption growth during the study period. Technology change is defined as alterations in production processes resulting in more or less consumption of metal per unit of output, often because of material substitutions and design changes. A trade analysis shows the significance of import growth, particularly indirect imports (metal contained in imported goods) as a factor contributing to the reduced growth rate of domestic metal production. The effect of import growth is partially offset by indirect export growth, suggesting that continued increase of all U.S. exports can have a strong effect in reducing the negative trade balance in metals.

Jan 1, 1988

"The major thrust of this research is directed towards a better undstanding of the behavior of airborne dust particles in underground mine airways. Figure 61 shows a schematic of dust flow in mine airway. The work included development of a mathematical model of dust behavior in mine airways, experimental study of the behavior of dust clouds and comparison of computer model output and experimental results. Re-entraiment is a secondary source of dust in mine airways and factors affecting re-entrainment are being identified.Investigations have encompassed both experimental and theoretical research into the behavior of dust in mine airways. Experiments were performed in mine airways under both controlled and normal operating conditions (Figure 62). The controlled experiments included the documentation of the concentration and desposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using real-time aerosol monitors (RAM-1) (Figure 63).On the theoretical front, a convection-diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion. Comparative analyses of results of the controlled experiments with the predictions of the mathematical model were carried out. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion were examined in light of the experimental observations."

Nov 1, 1988

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

By Edward A. Mihok

This paper presents plant design and cost estimates for limestone treatment of acid mine water covering a wide range of quality and quantity conditions. The treatment process consists of limestone neutralization, aeration, solids settling, and concentration. The design criteria for the various operation functions are based on pilot plant performance, laboratory data, and established mine water treatment standards. Unit costs have been assumed and are related to general market prices and conditions. These estimates serve as preliminary indicators of what it would cost to construct and operate a mine water treatment plant.

Jan 1, 1970

By Joseph J. Wallace

1. The investigation shows that there are 2 coal beds of major importance in Letcher County from the standpoint of present production - Upper Elkhorn No, 3 and Fire Clay - and 5 beds of minor importance - Whitesburg, Flag, Haddix, Elkhorn Leader, and Amburgy, The Upper Elkhorn No. 3 and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,600 tons per acre-foot of coal in place, are estimated at 1,353 million short tons as of January 1, 1952. Of this total, 1,056 million short tons ere in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bad characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By F. W. Wood

The method described may be used to delineate irregularities, inclusions, porosity, or shrink holes in ingots up to 43 inches in length. Rou¬tine testing does not require technical personnel, and the equipment is easily maintained. INTRODUCTION For a number of years, the Northwest Electrodevelopment Laboratory of the Bureau of Mines, Albany, Oreg., under contract with the Atomic Energy Commission and the Naval Reactors Division of the Bureau of Ships, has studied the production of zirconium and has adopted the Kroll magnesium-reduction process3/ as the, most economical means of producing high-purity zirconium sponge in quantities commensurate with demand. Consumable-electrode arc melting4/ provides a practical means of melting the sponge without increasing the impurity content. The ultimate application for which the metal is intended requires that strict specifications be met to insure workability and maintain the nuclear properties and corrosion resistance. The control measures employed to satisfy these specifications include chemical, spectrographic, and metallographic analyses, mechanical and corrosion tests, and ultrasonic inspection of the finished ingot. The primary purpose of ultrasonic inspection is to augment the other control measures by checking the soundness of each ingot leaving the laboratory. An incidental but important function has been the revelation of information leading to better understanding of the arc-melting process. For example, information obtained through ultrasonic inspection relative to the occurrence and distribution of porosity in ingots has resulted in a. modification of melting practices that minimizes the occurrence.

Jan 1, 1955

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

By N. S. Dalal, B. Jafarl, M. M. Suryan, V. Vallyathan

"The biologic events leading to coal workers' pneumoconiosis (C'WP) are not yet fully understood. There is no good correlation between toxicity studies or animal models with human epidemiologic and pathologic data. Several studies have shown that the severity and prevalence of the CWP in miners correlate strongly with the rank and type of the coal mined. However this has not been found to be the case with laboratory animal models or in vitro studies. In 1980 Russian scientists Artemov and Resnik suggested that the discrepancy may be related to the excessive amount of short-lived free radicals present in freshly generated coal mine dust. Because of their short life, such free radicals would be absent in the ""stale"" coal dust used in most animal experiments. To test this hypothesis we have undertaken a systematic study of the generation, reactivity with oxygen and biological significance of free radicals in coal dust.Electron spin resonance (ESR) was used as a technique for the direct detection of radical production and kinetics of decay. ESR signals from the newly generated radicals decreased with time on exposure to oxygen or when stored in biological buffers at a rapid rate. In vitro biological tests were carried out which suggest that the reaction between the newly generated radicals and oxygen plays a significant role in the sample's cytotoxicity.Materials and MethodsESR measurements were made at X-band (~9.7 GHz) using a computer-controlled Bruker ER200D ESR spectrometer. 11te two coals studied in detail were obtained from the Pennsylvania State University Coal Depository. These were, a bituminous sample, PSOC-1172 (72% carbon) and an anthracite sample, PSOC 867 (95% carbon). Coal particles of several millimeter (mm) dimensions were evacuated to a pressure of ~10-3 mm Hg typically overnight. Without exposure to air, these particles were ground in an agate mortar with an agate pestle for about 30 minutes and then sieved through a 20 \1111 mesh filter before ESR measurements or cytotoxicity studies. As an index of cytotoxicity, hemolysis was measured according to the method of Harrington, with minor modifications. Sheep erythrocytes (2%) were incubated with test samples at 37°C for one hour, and the hemoglobin released was quantitatively estimated photometrically. Additionally, release of alveolar macrophage enzyme lactate dehydrogenase (LOH) was estimated after incubation of the macrophages with the coal particles at different time intervals after the grinding. Enzyme activity was assayed according to the method of Wrobleski and LaDue and expressed as percent of enzyme released in 2 hours per million cells with 1 mg of coal."

Jan 1, 1989

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

Research by the National Institute for Occupational Safety and Health (NIOSH) on multiple-seam mining has resulted in two new ground control products. Information Circular (IC) 9495 In some U.S. coalfields, particularly in central Appalachia and the West, most mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously threaten the safety of miners and disrupt mining operations. Information Circular (IC) 9495 is a proceedings document containing a variety of papers that summarize recent knowledge about multiple-seam mining. A NIOSH study that analyzed case histories collected from 44 U.S. coal mines is described in detail. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. The study's results were the basis for the Analysis of Multiple-Seam Stability (AMSS) software package. The proceedings also contain two papers describing the LaModel family of software. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D implements a simplified, two-dimensional model suitable for quick approximations of the multiple-seam stresses and strains. Three papers in the proceedings focus on case histories. One describes the extensive multiple-seam experience at the Harris No. 1 Mine in West Virginia, a second contains examples of "extreme" multiple-seam mining from the central Appalachian coalfields, and a third describes interactions with regard to longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining. [ ] AMSS Software Package NIOSH has developed a simple, user-friendly computer program called Analysis of Multiple-Seam Stability (AMSS). AMSS can help mine planners to evaluate each potential multiple-seam interaction and take steps to reduce the risk of ground control failure. AMSS begins by evaluating the pillar design. It first calculates the single-seam pillar stability factor (SF)

Jan 11, 2007

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By John J. Mulligan

The Bureau of Mines sampled a gold-bearing schist series 50 miles east of Nome near Bluff, a dormant mining camp on the southern shore of the Seward Peninsula, Alaska. Gold is unevenly distributed through a section of a schist series that extends from the coast northward 4,500 feet. In this section the schists dip westward 20 to 38 degrees and have an outcrop width of about 1,000 feet and a normal width of about 500 feet. An intensely fractured zone within the schists averages 0.015 to 0.017 ounce of gold and 0.03 to 0.05 ounce of silver per ton for outcrop widths of 200 to almost 500 feet. The grade of the remainder of the schist series ranges downward to scant traces. Gold eroded from these schists collected in solution channels in metalimestones to form the Daniels Creek placers, which also extend from the beach southward under the sea for an unknown distance. The lode sources of the gold placers elsewhere in the southern Seward Peninsula may be similar schists that occupy a similar position in the metasedimentary series.

Jan 1, 1971

By L. D. Patts, J. D. Noll, S. E. Mischler, G. H. Schnakenberg

In this study, we evaluated the ambient diesel particulate matter (DPM) concentrations (at the intakes and exhausts of the mine) as the entire vehicle fleet of a stone mine switched from using 35% biodiesel to using a water emulsified fuel (PuriNOx). Elemental carbon (EC) was reduced by 45% when a PuriNOx blend containing 10% water replaced 35% biodiesel and by 57% when a PuriNOx blend containing 20% water was used. Other factors such as engine duty cycle and production changes could potentially cause some day-to-day EC fluctuations, and no direct comparison to commonly used dieselfuels (No. 1 or No. 2) was achieved. Therefore, a second study was performed in a controlled “isolatedzone” environment to fametal mine, comparing PuriNOxto No.1 diesel fuel in a load haul dump vehicle. The EC fraction of the DPM was reduced by about 71% when the PuriNOx blend containing 10% water was used and by about 85% when the PuriNOx blend containing 20% water was employed. This study did not determine how the water emulsified fuel would affect the engine or power.