Search Documents

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By Suresh K. Bhatt, Dennis R. Dolinar

The roof bolt system of a mine, if properly selected and installed, can allow for better roof control and reduce the potential for roof falls. Because of this potential to reduce roof falls and improve ground control conditions, the National Institute for Occupational Safety and Health (NIOSH) has an interest in the types of roof bolts that are used by the coal industry. Further, NIOSH has conducted research into how various support parameters can affect the number of roof falls that occur, including support type. Today, the five main types of roof bolts installed in U.S. coal mines are mechanical anchor bolts, point-anchor or resin-assisted mechanical anchor bolts, torque-tension bolts, combination bolts, and fully grouted resin rebar. This paper describes each support in detail. Because of the importance of resin in the functioning of the majority of bolts installed, resin grouts are also discussed. Further, trends in the types of roof bolts used are reviewed. Over the last 10 years, the significant trend has been the large reduction in the relative number of mechanical anchor bolts that are installed. These bolts have been replaced mainly by the resin-grouted rebar system. Data are also presented to show the impact of these changes in bolting on the number of roof falls.

Jan 10, 2000

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1984

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1984

By Rose L. Ballard

This chapter summarizes data on crude non fuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal non fuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production, The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1986

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may he measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing. the stage of measurement used in this chapter is what is normally termed ?mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Jan 1, 2009

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Feb 1, 2009

By Arthur M. Hartstein

The Bureau of Mines through contract with Ultrasystems, Inc., obtained gram per gram data of products formed on thermal oxidative degradation of selected compositions, both under dynamic and static conditions. Four broad classes of materials were studied! Polyvinyl chloride compositions, neoprene compositions, rigid urethane foams, and variously treated woods. Whenever possible, comparisons between pure components and composites were attempted. Thermogravimetric and differential thermal analyses were performed to gain understanding of the processes occurring and to explore the feasibility of using these analyses as a method of material identification. The toxic products detected and quantitated included HC1, H2S, CO, S02, CS2,COS, HCOOH, CH3COOH, formaldehyde, acrolein, C 6H6, chloroprene, chloroethanol, benzyl chloride, aniline, and furfural.

Jan 1, 1974

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of selected ingredients employed in the formulation and manufacture of conveyor belts. This work was done to supplement similar studies of samples from finished conveyor belts and thus provide basic data for correlation of the potential toxic behavior of a finished belt with that of the individual ingredients. This report covers the study of (1) basic polymers (styrene-butadiene, neoprene), (2) reinforcing fibers (Nylon 6,6, Dacron, viscose rayon), (3) flame-retardant plasticizers (tritolyl phosphate-isomeric mixture, tri-p-tolyl phosphate, tributyl phosphate, tris (dichloropropyl) phosphate), (4) plasticizers (diphenylphtha1ate, di-(2-ethylhexyl) sebacate), and (5) a vulcanization accelerator (2-mercaptobenzothiazole).

Jan 1, 1977

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

Strategies for monitoring methane levels during roof bolting in an extended cut entry were evaluated. Testing was conducted at the Pittsburgh Research Laboratory’s methane test gallery. Operating conditions were varied and methane releases at the face and drill holes were simulated. Methane readings were taken at the face, and at locations outby the face. Results show that, when the major source of methane was at the drill holes, the highest methane readings were at locations on or 6.1 m (20ft) inby the bolting machine. Methods for selecting better outby sampling locations, when the majority of the methane is released at the face, are examined. During roof bolting it is easier to sample at these outby locations rather than at the face. Further testing is needed to determine what relationship exists between methane concentrations at the outby locations and at the source of the methane release.

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

Eliminate accidental tramming of a cleanup tractor. Approach A switch was installed in the operator's seat cushion to pre-vent the cleanup tractor from tramming without an operator in the driver's seat. How It Works The operator must be seated, and the Forward/Reverse Switch (that controls tramming direction) must pass through the NEUTRAL position before the vehicle will tram. See Figure 1. A pressure-sensitive seat cushion switch, a solid-state relay, and a double-contact relay were added to the control circuitry of an S & S BMUAT -88 cleanup tractor to create this tramming interlock. The weight of the operator on the cushion closes the seat cushion switch (Figure 2, A). This activates the solid-state relay (B), which completes the initial circuitry. Moving the For- ward/Reverse Switch (C) to NEUTRAL energizes the coil in the double-contact relay (D) and closes both contacts. One contact completes a sustaining circuit which keeps the double-contact relay energized. The second contact transfers power to the remaining contacts within the Forward/ Reverse Switch. These circuits are shown in greater de- tail in Figure 2.

Jan 1, 1978

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936